EN ISO 11296-3:2018
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
This document, in conjunction with ISO 11296‑1, specifies requirements and test methods for close-fit lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U) as manufactured, as well to the installed lining system with its associated joints.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-3:2018)
Dieses Dokument legt in Verbindung mit ISO 11296-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme die zur Renovierung von erdverlegten Abwasserkanälen und –leitungen verwendet werden, fest.
Es gilt sowohl für Rohre und Formstücke aus Polyethylen (PE) oder weichmacherfreiem Polyvinylchlorid (PVC-U) wie hergestellt, als auch für das installierte Lining-System mit seinen zugehörigen Verbindungen.
Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11296-3:2018)
Le présent document, conjointement à l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubage par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression.
Il s'applique aux tuyaux et aux raccords en polyéthylène (PE) ou en poly(chlorure de vinyle) non plastifié (PVC-U) tels que fabriqués, aussi qu'au système de tubage installé avec ses assemblages associés.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2018)
Ta dokument skupaj s standardom ISO 11296-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme cevi, ki se uporabljajo za obnavljanje podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka. Uporablja se za cevi in fitinge, izdelane iz polietilena (PE) ali nemehčanega polivinilklorida (PVC‑U) kot so izdelani, pa tudi za nameščene tesno prilagodljive sisteme cevi z ustreznimi spoji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 11296-3:2011
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3.
del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2018)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-
3:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 3:
Tubage par tuyau continu sans espace annulaire (ISO 11296-3:2018)
Ta slovenski standard je istoveten z: EN ISO 11296-3:2018
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11296-3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN ISO 11296-3:2011
English Version
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 3:
Lining with close-fit pipes (ISO 11296-3:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux de branchements et de von erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO
Partie 3: Tubage par tuyau continu sans espace 11296-3:2018)
annulaire (ISO 11296-3:2018)
This European Standard was approved by CEN on 5 August 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-3:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11296-3:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11296-3:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11296-3:2018 has been approved by CEN as EN ISO 11296-3:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-3
Second edition
2018-08
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11296-3:2018(E)
©
ISO 2018
ISO 11296-3:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 11296-3:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General . 2
3.2 Techniques . 2
3.3 Characteristics . 2
3.4 Materials . 2
3.5 Product stages . 2
3.6 Service conditions . 2
3.7 Joints . 3
4 Symbols and abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.1.1 General. 3
5.1.2 Distinction between PVC-U types . 3
5.1.3 Virgin material . 3
5.1.4 Reprocessable material and recyclable material . 3
5.2 General characteristics . 4
5.2.1 Appearance . 4
5.2.2 Colour . 4
5.3 Material characteristics . 4
5.4 Geometric characteristics . 5
5.5 Mechanical characteristics. 5
5.6 Physical characteristics . 5
5.7 Jointing . 5
5.8 Marking . 6
6 Fittings at the “M” stage . 6
7 Ancillary components . 6
8 Fitness for purpose of the installed lining system at the “I” stage .6
8.1 Materials . 6
8.2 General characteristics . 6
8.3 Material characteristics . 6
8.4 Geometric characteristics . 6
8.5 Mechanical characteristics. 8
8.6 Physical characteristics . 9
8.7 Additional characteristics . 9
8.8 Sampling .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.