EN ISO 11298-2:2018
(Main)Plastics piping systems for renovation of underground water supply networks - Part 2: Lining with continuous pipes (ISO 11298-2:2018)
Plastics piping systems for renovation of underground water supply networks - Part 2: Lining with continuous pipes (ISO 11298-2:2018)
ISO 11298-2:2018, read in conjunction with ISO 11298-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"); see Annex A.
In addition, ISO 11298-2:2018 covers
- jointing of pipe lengths by means of butt fusion, and
- fabricated and injection-moulded fittings made of PE.
ISO 11298-2:2018 is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Wasserversorgungsnetzen - Teil 2: Rohrstrang-Lining (ISO 11298-2:2018)
Dieses Dokument legt in Verbindung mit ISO 11298 1 die Anforderungen und Prüfverfahren für Rohre und Formstücke, die Teil eines als Rohrstrang eingebauten Rohrleitungssystems für die Renovierung von erdverlegten Wasserversorgungsnetzen sind, fest. Es gilt für drei verschiedene Arten von PE Rohren:
- einschichtige PE Vollwandrohre (Nenn-Außendurchmesser, dn), einschließlich etwaiger Identifi-zierungsstreifen;
- PE Rohre mit koextrudierten Schichten auf der Außen- und/oder Innenseite des Rohres (Gesamt-Außendurchmesser, dn), wie in Anhang A angegeben, wobei alle Schichten über die gleiche erforderliche Mindestfestigkeit verfügen;
- PE beschichtete Rohre (Außendurchmesser, dn), die über eine abziehbare, aufliegende, thermoplastische Zusatzschicht auf der Außenseite des Rohres ("beschichtetes Rohr") verfügen, siehe Anhang A.
Es schließt außerdem Folgendes ein:
- Verbinden von Rohrstücken durch Stumpfschweißen; und
- gefertigte und Spritzguss-Formstücke aus PE.
Es gilt für PE Rohre, Formstücke und Bauteilkombinationen, die für die Verwendung bei einer Betriebstemperatur von 20 °C als Bezugstemperatur vorgesehen sind.
ANMERKUNG Für Anwendungen, die bei einer konstanten Temperatur von über 20 °C und bis zu 40 °C betrieben werden, siehe ISO 4427 1:2007, Anhang A.
Systémes de canalisation en plastiques pour la rénovation des réseaux enterrés d’alimentation en eau - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO 11298-2:2018)
ISO 11298-2:2018, lu conjointement avec l'ISO 11298‑1, spécifie les exigences et les méthodes d'essai pour des tuyaux et raccords intégrés aux systèmes de canalisations en plastique installés sous forme de tuyaux continus et utilisés pour la rénovation des réseaux des réseaux enterrés d'alimentation en eau. Il s'applique aux tuyaux en PE de trois types différents:
- tuyaux en PE monocouches à paroi compacte (diamètre extérieur nominal, dn), y compris les bandes d'identification éventuelles;
- tuyaux en PE avec des couches co-extrudées à l'extérieur et/ou à l'intérieur du tuyau (diamètre extérieur total, dn), tels que spécifiés dans l'Annexe A, toutes les couches ayant la même classification MRS;
- tuyaux revêtus de PE (diamètre extérieur, dn) comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau («tuyau revêtu»), voir l'Annexe A.
ISO 11298-2:2018 couvre également:
- l'assemblage des longueurs de tuyau par soudage bout à bout;
- les raccords en PE façonnés et moulés par injection.
ISO 11298-2:2018 s'applique aux tuyaux, raccords et montages en PE destinés à être utilisés à une température de fonctionnement de 20 °C, qui est la température de référence.
NOTE Pour les applications à des températures constantes comprises entre 20 °C et 40 °C, voir l'ISO 4427‑1:2007, Annexe A.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11298-2:2018)
Ta mednarodni standard, bran v povezavi s 1. delom, določa zahteve in preskusne metode za cevi in fitinge, ki so del plastičnih cevnih sistemov, nameščenih kot neprekinjene cevi pri obnovi podzemnih omrežij za oskrbo z vodo. Uporablja se za PE cevi treh različnih tipov: – PE trdne stenske cevi iz ene plasti (nazivni zunanji premer, DN) s kakršnimi koli identifikacijskimi črtami;
– PE cevi s koekstrudiranimi sloji na zunanji in/ali notranji strani cevi (celotni zunanji premer, DN), kot je opredeljeno v dodatku A, pri čemer imajo vsi sloji enako oceno MRS;
– PE prevlečene cevi (zunanji premer, DN) s termoplastičnim dodatnim slojem, ki ga je mogoče odluščiti, na zunanji strani cevi (»prevlečena cev«), glej dodatek A.
Poleg tega zajema: – spajanje dolžin cevi s soležnim taljenjem;
– oblikovane in brizgano lite fitinge iz PE.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2018
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z
vodo - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11298-2:2018)
Plastics piping systems for renovation of underground water supply networks - Part 2:
Lining with continuous pipes (ISO 11298-2:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Wasserversorgungsnetzen - Teil 2: Rohrstrang-Lining (ISO 11298-2:2018)
Systémes de canalisation en plastiques pour la rénovation des réseaux enterrés
d’alimentation en eau - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO
11298-2:2018)
Ta slovenski standard je istoveten z: EN ISO 11298-2:2018
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11298-2
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 93.025
English Version
Plastics piping systems for renovation of underground
water supply networks - Part 2: Lining with continuous
pipes (ISO 11298-2:2018)
Systémes de canalisation en plastiques pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux enterrés d'alimentation en eau von erdverlegten Wasserversorgungsnetzen - Teil 2:
- Partie 2: Tubage par tuyau continu avec espace Rohrstrang-Lining (ISO 11298-2:2018)
annulaire (ISO 11298-2:2018)
This European Standard was approved by CEN on 27 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11298-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11298-2:2018) has been prepared by Technical Committee ISO/TC 138
“Rehabilitation of pipeline systems” in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11298-2:2018 has been approved by CEN as EN ISO 11298-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11298-2
First edition
2018-02
Plastics piping systems for renovation
of underground water supply
networks —
Part 2:
Lining with continuous pipes
Systémes de canalisation en plastiques pour la rénovation des réseaux
enterrés d’alimentation en eau —
Partie 2: Tubage par tuyau continu avec espace annulaire
Reference number
ISO 11298-2:2018(E)
©
ISO 2018
ISO 11298-2:2018(E)
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2018 – All rights reserved
ISO 11298-2:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 2
4.1 Symbols . 2
4.2 Abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Material . 3
5.2 General characteristics . 3
5.3 Material characteristics . 3
5.4 Geometrical characteristics . 3
5.5 Mechanical characteristics. 3
5.6 Physical characteristics . 3
5.7 Jointing . 3
5.8 Marking . 3
5.9 Regional requirements for pipes . 4
6 Fittings at the “M” stage . 4
6.1 Requirements . 4
6.2 Marking . 4
6.3 Regional requirements for fittings . 4
7 Ancillary components . 4
8 Fitness for purpose of the system for pipes and fittings at the “I” stage .4
9 Installation practice . 4
9.1 Preparatory work . 4
9.2 Storage, handling and transport . 4
9.3 Equipment . 5
9.3.1 Butt fusion equipment and debeading equipment. 5
9.3.2 Pipe rollers . 5
9.3.3 Winching and rod-pulling equipment . 5
9.3.4 Pipe entry guides . 5
9.3.5 Electrofusion equipment . 6
9.3.6 Inspection equipment . 6
9.3.7 Lifting equipment . 6
9.4 Installation . 6
9.5 Process-related inspection and testing . 7
9.6 Lining termination . 7
9.7 Reconnection to the existing pipeline system . 7
9.8 Final inspection and testing . 7
9.9 Documentation . 7
Annex A (normative) Layered pipes . 8
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.