iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 11298-1:2018

(Main)

Plastics piping systems for renovation of underground water supply networks — Part 1: General

Plastics piping systems for renovation of underground water supply networks — Part 1: General

ISO 11298-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground water supply networks. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler. ISO 11298-1:2018 gives the general requirements common to all relevant renovation techniques.

Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau — Partie 1: Généralités

ISO 11298-1:2018 spécifie les exigences et les méthodes d'essai des systèmes de canalisations en plastique destinés à être utilisés pour la rénovation des réseaux enterrés d'alimentation en eau. Il s'applique aux tuyaux et raccords, tels que fabriqués, ainsi qu'au système de rénovation installé. Il ne s'applique pas à la canalisation existante, aux enduits projetés non structurels, ni à tout matériau de remplissage annulaire. ISO 11298-1:2018 donne les exigences générales communes à toutes les techniques de rénovation pertinentes.

General Information

Status
Published
Publication Date
25-Feb-2018
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
93.025 - External water conveyance systems
Technical Committee
ISO/TC 138/SC 8 - Rehabilitation of pipeline systems
Drafting Committee
ISO/TC 138/SC 8/WG 3 - Plastics piping systems for rehabilitation of underground water supply networks
Current Stage
9092 - International Standard to be revised
Completion Date
21-Mar-2024
Ref Project

Relations

Consolidates
ISO 8673:2012 - Hexagon regular nuts (style 1) with metric fine pitch thread — Product grades A and B
Effective Date
06-Jun-2022
Revises
ISO 11298-1:2010 - Plastics piping systems for renovation of underground water supply networks — Part 1: General
Effective Date
14-Nov-2015

Buy Standard

ISO 11298-1:2018 - Plastics piping systems for renovation of underground water supply networksISO 11298-1:2018 - Plastics piping systems for renovation of underground water supply networks
PreviousNext
Standard
ISO 11298-1:2018 - Plastics piping systems for renovation of underground water supply networks
English language
16 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 11298-1:2018 - Systemes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eauISO 11298-1:2018 - Systemes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau
PreviousNext
Standard
ISO 11298-1:2018 - Systemes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau
French language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11298-1
Second edition
2018-03
Plastics piping systems for renovation
of underground water supply
networks —
Part 1:
General
Systèmes de canalisations en plastique pour la rénovation des réseaux
enterrés d'alimentation en eau —
Partie 1: Généralités
Reference number
ISO 11298-1:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 11298-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11298-1:2018(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 8
4.1 Symbols . 8
4.2 Abbreviated terms . 8
5 Pipes at the “M” stage . 9
5.1 Materials . 9
5.2 General characteristics . 9
5.3 Material characteristics . 9
5.4 Geometric characteristics . 9
5.5 Mechanical characteristics. 9
5.6 Physical characteristics . 9
5.7 Jointing . 9
5.8 Marking . 9
6 Fittings at the “M” stage .10
6.1 M
...

NORME ISO
INTERNATIONALE 11298-1
Deuxième édition
2018-03
Systèmes de canalisations en plastique
pour la rénovation des réseaux
enterrés d'alimentation en eau —
Partie 1:
Généralités
Plastics piping systems for renovation of underground water supply
networks —
Part 1: General
Numéro de référence
ISO 11298-1:2018(F)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 11298-1:2018(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 11298-1:2018(F)

Sommaire Page
Avant-propos .v
Introduction .vi
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles et abréviations . 8
4.1 Symboles . 8
4.2 Abréviations . 9
5 Tuyaux au stade «M» . 9
5.1 Matières . 9
5.2 Caractéristiques générales. 9
5.3 Caractéristiques des matières . 9
5.4 Caractéristiques géométriques . 9
5.5 Caractéristiques mécaniques . 9
5.6 Caractéristiques physiques . 9
5.7 Assemblage .10
5.8 Marquage .10
6 Raccords au stade «M» .10
6.1 Matières .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 11298-4:2021(Main)
Plastics piping systems for renovation of underground water supply networks — Part 4: Lining with cured-in-place pipes

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1). It does not include requirements or test methods for resistance to cyclic loading or the pressure rating of CIPP liners where passing through bends, which are outside the scope of this document. It is applicable to cured-in-place pipe lining systems intended to be used at a service temperature of up to 25 °C. NOTE For applications operating at service temperatures greater than 25 °C, guidance on re-rating factors can be supplied by the system supplier.

  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off
  • Draft
    38 pages
    English language
    sale 15% off
  • Draft
    42 pages
    French language
    sale 15% off
ISO
ISO 11298-3:2018(Main)
Plastics piping systems for renovation of underground water supply networks — Part 3: Lining with close-fit pipes

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off
ISO
ISO 11298-2:2018(Main)
Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes

ISO 11298-2:2018, read in conjunction with ISO 11298-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types: - PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; - PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; - PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"); see Annex A. In addition, ISO 11298-2:2018 covers - jointing of pipe lengths by means of butt fusion, and - fabricated and injection-moulded fittings made of PE. ISO 11298-2:2018 is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
ISO
ISO 11298-4:2021(Main)
Plastics piping systems for renovation of underground water supply networks — Part 4: Lining with cured-in-place pipes

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1). It does not include requirements or test methods for resistance to cyclic loading or the pressure rating of CIPP liners where passing through bends, which are outside the scope of this document. It is applicable to cured-in-place pipe lining systems intended to be used at a service temperature of up to 25 °C. NOTE For applications operating at service temperatures greater than 25 °C, guidance on re-rating factors can be supplied by the system supplier.

  • Standard
    39 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off
  • Draft
    38 pages
    English language
    sale 15% off
  • Draft
    42 pages
    French language
    sale 15% off
ISO
ISO 21307:2017/Amd 1:2020(Amendment)
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems — Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
ISO
ISO 4427-5:2019(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 5: Fitness for purpose of the system

This document specifies the characteristics of the fitness for purpose of pipes and/or fittings assemblies made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges. NOTE 2 This document is intended to be only used by the product manufacturer to assess the performance of components according to ISO 4427‑2 and/or ISO 4427‑3 when joined together under normal and extreme conditions. It is not intended for on-site testing of pipe systems. This document also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, fittings, their joints and to joints with components of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1]; b) an operating temperature of 20 °C as the reference temperature. NOTE 3 For other operating temperatures, guidance is given in ISO 4427‑1: 2019, Annex A. The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    9 pages
    English language
    sale 15% off
ISO
ISO 4427-1:2019(Main)
Plastics piping systems for water supply and for drainage and sewerage under pressure — Polyethylene (PE) — Part 1: General

This document specifies the general aspects of polyethylene (PE) compounds for the manufacture of pressure pipes and fittings (mains and service pipes) for buried or above ground applications, intended for the conveyance of: — water for human consumption; — raw water prior to treatment; — drainage and sewerage under pressure; — vacuum sewer systems; — water for other purposes. This document also specifies the test parameters and requirements for the test methods referred to in this document. In conjunction with other parts of the ISO 4427 series, this document is applicable to PE pipes and fittings, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1]; b) an operating temperature of 20 °C as the reference temperature. NOTE 1 For other operating temperatures, guidance is given in Annex A. The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    17 pages
    English language
    sale 15% off
ISO
ISO 11298-3:2018(Main)
Plastics piping systems for renovation of underground water supply networks — Part 3: Lining with close-fit pipes

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off
ISO
ISO 11298-2:2018(Main)
Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes

ISO 11298-2:2018, read in conjunction with ISO 11298-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types: - PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; - PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; - PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"); see Annex A. In addition, ISO 11298-2:2018 covers - jointing of pipe lengths by means of butt fusion, and - fabricated and injection-moulded fittings made of PE. ISO 11298-2:2018 is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
ISO
ISO 21307:2017(Main)
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems

ISO 21307:2017 establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion jointing of polyethylene (PE) piping system components specified in accordance with relevant ISO standards. These components are installed in accordance with the relevant codes of practice, national regulations or industry guidance. Specifically, this document specifies three butt fusion jointing procedures for PE pipes and fittings. These are: - single low-pressure fusion jointing procedure; - dual low-pressure fusion jointing procedure; - single high-pressure fusion jointing procedure. ISO 21307:2017 takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards.

  • Standard
    16 pages
    English language
    sale 15% off