iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13374:2013/prA1:2017

(Amendment)

Temporary edge protection systems - Product specification - Test methods

Temporary edge protection systems - Product specification - Test methods

This European Standard specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This standard applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this standard specifies requirements for energy absorption.
This standard includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This standard does not provide requirements for edge protection systems intended for:
- protection against impact from vehicles or from other mobile equipment,
- protection from sliding down of bulk loose materials, snow etc,
- protection of areas accessible to the public.
This standard does not apply to side protection on scaffolds according to EN 12811-1 and EN 1004.
NOTE   This does not prevent these systems to be used on temporary structures, or enhance the protection provided on scaffolds defined under EN 12811-1 or EN 1004. If this is intended, additional testing will be carried out.

Temporäre Seitenschutzsysteme - Produktfestlegungen - Prüfverfahren

Garde-corps périphériques temporaires - Spécification du produit - Méthodes d'essai

Začasne ograje - Specifikacija proizvoda - Metode preskušanja

General Information

Status
Not Published
ICS
13.340.99 - Other protective equipment
91.220 - Construction equipment
Technical Committee
CEN/TC 53 - Temporary works equipment
Drafting Committee
CEN/TC 53/WG 10 - Guardrails for temporary works
Current Stage
Ref Project
SIST EN 13374:2013/oprA1:2017 - Temporary edge protection systems - Product specification - Test methods

Relations

Merged Into
EN 13374:2013+A1:2018 - Temporary edge protection systems - Product specification - Test methods
Effective Date
18-Jan-2023
Amends
EN 13374:2013 - Temporary edge protection systems - Product specification - Test methods
Effective Date
10-Aug-2016

Buy Standard

EN 13374:2013/oprA1:2017EN 13374:2013/oprA1:2017
PreviousNext
Draft
EN 13374:2013/oprA1:2017
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2017
=DþDVQHRJUDMH6SHFLILNDFLMDSURL]YRGD0HWRGHSUHVNXãDQMD
Temporary edge protection systems - Product specification - Test methods
Temporäre Seitenschutzsysteme - Produktfestlegungen - Prüfverfahren
Garde-corps périphériques temporaires - Spécification du produit - Méthodes d'essai
Ta slovenski standard je istoveten z: EN 13374:2013/prA1
ICS:
13.340.99 Druga varovalna oprema Other protective equipment
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 13374:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2017
ICS 13.340.99; 91.220
English Version
Temporary edge protection systems - Product
specification - Test methods
Garde-corps périphériques temporaires - Spécification Temporäre Seitenschutzsysteme -
du produit - Méthodes d'éssai Produktfestlegungen - Prüfverfahren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 53.

This draft amendment A1, if approved, will modify the European Standard EN 13374:2013. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13374:2013/prA1:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Modification to 5.2.1, Edge protection system class A . 4
2 Modification to 5.2.2, Edge protection system class B .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13374:2013+A1:2018(Main)
Temporary edge protection systems - Product specification - Test methods
SIST EN 13374:2013+A1:2019

This document specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This document applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this standard specifies requirements for energy absorption.
This standard includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This standard does not provide requirements for edge protection systems intended for:
- protection against impact from vehicles or from other mobile equipment,
- protection from sliding down of bulk loose materials, snow etc,
- protection of areas accessible to the public.
This standard does not apply to side protection on scaffolds according to EN 12811-1 and EN 1004.
NOTE This does not prevent these systems to be used on temporary structures.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 13374:2024(Main)
Temporary edge protection systems - Product specification - Test methods
kSIST FprEN 13374:2024

This document specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This document applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this document specifies requirements for energy absorption.
This document includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This document does not provide requirements for edge protection systems intended for:
—   protection against impact from vehicles or from other mobile equipment,
—   protection from sliding down of bulk loose materials, snow etc,
—   protection of areas accessible to the public.
This document does not apply to side protection on scaffolds according to EN 12811 1 and EN 1004 1.
NOTE   This does not prevent these systems to be used on temporary structures.

  • Draft
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13374:2013+A1:2018(Main)
Temporary edge protection systems - Product specification - Test methods
SIST EN 13374:2013+A1:2019

This document specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This document applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this standard specifies requirements for energy absorption.
This standard includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This standard does not provide requirements for edge protection systems intended for:
- protection against impact from vehicles or from other mobile equipment,
- protection from sliding down of bulk loose materials, snow etc,
- protection of areas accessible to the public.
This standard does not apply to side protection on scaffolds according to EN 12811-1 and EN 1004.
NOTE This does not prevent these systems to be used on temporary structures.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 13374:2024(Main)
Temporary edge protection systems - Product specification - Test methods
kSIST FprEN 13374:2024

This document specifies the requirements and test methods for temporary edge protection systems for use during construction or maintenance of buildings and other structures.
This document applies to edge protection systems for flat and inclined surfaces and specifies the requirements for three classes of temporary edge protection.
For edge protection systems with an arrest function (e.g. falling or sliding down a sloping roof) this document specifies requirements for energy absorption.
This document includes edge protection systems, some of which are fixed to the structure and others, which rely on gravity and friction on flat surfaces.
This document does not provide requirements for edge protection systems intended for:
—   protection against impact from vehicles or from other mobile equipment,
—   protection from sliding down of bulk loose materials, snow etc,
—   protection of areas accessible to the public.
This document does not apply to side protection on scaffolds according to EN 12811 1 and EN 1004 1.
NOTE   This does not prevent these systems to be used on temporary structures.

  • Draft
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17339:2024(Main)
Transportable gas cylinders – Hoop wrapped and fully wrapped carbon composite cylinders and tubes for hydrogen
kSIST FprEN 17339:2024

This document specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of composite gas cylinders and tubes for compressed hydrogen.
NOTE 1 Unless specified in the text, for the purposes of this document, the word “cylinder” includes tubes.
This document applies to
-   fully wrapped composite cylinders (Type 3 and Type 4)
-   hoop wrapped cylinders (Type 2)
with carbon fibres intended to be permanently mounted in a frame (e.g. bundle or trailer) with a test pressure of not less than 300 bar, with:
— non-metallic liners (for Type 4) or seamless metallic liners (for Type 2 and Type 3),
— a maximum water capacity of 3 000 l
— a maximum working pressure of 1 000 bar.
— the product of working pressure times water capacity (p x V) not exceeding 1 000 000 bar.l.
NOTE 2 A glass fibre protective layer is sometimes applied to the external surface of the cylinder

  • Draft
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 7552-2:2024(Main)
Molecular in vitro diagnostic examinations - Specifications for pre-examination processes for circulating tumour cells (CTCs) in venous whole blood - Part 2: Isolated DNA (ISO/TS 7552-2:2024)
kSIST-TS FprCEN ISO/TS 7552-2:2024

This document specifies requirements and gives recommendations on the handling, storage, CTC enrichment and isolation, DNA isolation and storage, and documentation of venous whole blood specimens intended for the examination of DNA isolated from circulating tumour cells (CTCs) during the pre-examination phase before a molecular examination is performed.
This document is applicable to molecular in vitro diagnostic examinations including laboratory developed tests performed by medical laboratories. It is also intended to be used by laboratory customers, in vitro diagnostics developers and manufacturers, biobanks, institutions, and commercial organizations performing biomedical research, and regulatory authorities.
This document does not cover the isolation of genomic DNA directly from venous whole blood containing CTCs. This is covered in ISO 20186-2.
This document does not cover the isolation of specific white blood cells and subsequent isolation of genomic DNA therefrom or the pre-analytical workflow requirements for viable CTC cryopreservation and culturing.
NOTE 1        The requirements given in this document can also be applied to other circulating rare cells (e.g. foetal cells).
NOTE 2        International, national, or regional regulations or requirements can also apply to specific topics covered in this document.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12520:2024(Main)
Furniture - Safety, strength and durability - Requirements for domestic seating
kSIST FprEN 12520:2024

This document specifies the minimum requirements for the safety, strength and durability of all types of domestic seating for adults. It also specifies additional test methods for seat side-to-side durability as well as finger entrapment and shear and compression.
It does not apply to ranked seating, seating for non-domestic use, office work chairs, chairs for educational institutions, outdoor seating and to links for linked seating for which European Standards exist.
It does not include requirements for the durability of upholstery materials, castors, reclining and tilting mechanisms and seat height adjustment mechanisms.
It does not include requirements for electrical safety.
It does not include requirements for the resistance to ageing, degradation, flammability and ergonomics.
The requirements are based on use by persons weighing up to 110 kg.
Annex A (normative) specifies the seat side-to-side durability test in D-G points.
Annex B (informative) gives rationales for some of the tests referred to in Table 1.
Annex C (normative) specifies the test methods for finger entrapment and shear and compression.
Annex D (normative) specifies the seat loading point for seating with suspended flexible material.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 7552-3:2024(Main)
Molecular in vitro diagnostic examinations - Specifications for pre-examination processes for circulating tumour cells (CTCs) in venous whole blood - Part 3: Preparations for analytical CTC staining (ISO/TS 7552-3:2024)
KSIST-TS FprCEN ISO/TS 7552-3:2024

This document specifies requirements and gives recommendations on the handling, storage, CTC enrichment, preparation for CTC staining, and documentation of venous whole blood specimens intended for staining of CTCs during the pre-examination phase before an examination is performed.
This document is applicable to molecular in vitro diagnostic examinations including laboratory developed tests performed by medical laboratories. It is also intended to be used by laboratory customers, in vitro diagnostics developers, and manufacturers, biobanks, institutions, and commercial organizations performing biomedical research, and regulatory authorities.
This document does not cover pre-analytical workflow requirements for viable CTC cryopreservation and culturing.
Different dedicated measures are taken for stabilizing CTCs genomic DNA and RNA that are not described in this document; they are covered in ISO 7552-1 and ISO 7552-2.
NOTE 1        The requirements given in this document can also be applied to other circulating rare cells (e.g. foetal cells).
NOTE 2        International, national or regional regulations or requirements can also apply to specific topics covered in this document.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 81-31:2024(Main)
Safety rules for the construction and installation of lifts - Lifts for the transport of goods only - Part 31: Accessible goods only lifts
oSIST prEN 81-31:2022

1.1   This document specifies the safety rules for new accessible goods only lifts with traction, positive or hydraulic drive, permanently installed and only used by users (see 3.57), serving fixed and permanent landing levels, having a carrier made of a single load carrying area, designed for the transportation of goods only, moving along a fixed path by rigid guide rails and inclined not more than 15° to the vertical, with rated speed not exceeding 1 m/s.
This document covers accessible goods only lifts with rated load exceeding 300 kg and not intended to transport persons.
1.2   For the purpose of this document, a goods only lift carrier is regarded as accessible where one of the following conditions is satisfied:
a)   floor area of the carrier is greater than 1,0 m2;
b)   depth of the carrier is greater than 1,0 m;
c)   clear height of the carrier is greater than 1,20 m.
In case the carrier is without a roof, it is considered accessible when the clear height of the landing doors is greater than 1,20 m.
1.3   Two types of accessible goods only lifts are addressed:
a)   Type A, where the intended use is bound to the maximum rated speed of 0,30 m/s;
b)   Type B, where the intended use is bound to the maximum rated speed of 1,0 m/s.
1.4   In addition to the requirements of this document, supplementary requirements are to be considered in special cases (operation subject to ATEX rules, operational in ambiental condition not addressed by this standard, seismic conditions, transporting dangerous goods, etc.).
1.5   This document does not cover:
a)   accessible goods only lifts:
1)   with more than one lift machine;
i)   where loading and unloading is automated, or the carrier floor is fitted with mobile devices (e.g. rollers) for loading and unloading purposes;
ii)   intended to carry bulk loads (such as loose sand, gravel, etc.);
iii)   with drive systems other than those stated in 4.8;
b)   lifting tables according to EN 1570-1 and EN 1570-2;
c)   lifting appliances, such as appliances with more than one carrier, skips, goods only lifts for construction sites, for underground applications, mine winding gear, goods only lifts on seagoing vessels and mobile offshore units, construction and maintenance appliances in wind turbines, goods only lifts specially designed and constructed for research purposes for temporary use in laboratories, goods only lifts specially designed and constructed for military or police purposes;
d)   safety during operation of transport, erection, repairs and dismantling of accessible goods only lifts;
e)   the use of translucent material for the walls of the well and machinery spaces, for the carrier with the exception of the landing doors vision panels;
f)   the use of programmable electronic systems in safety related applications for lifts (PESSRAL);
g)   hydraulic lifts where the setting of the pressure relief valve exceeds 50 MPa;
h)   any form of radiation except EMC;
i)   fire propagation;
j)   energy dissipation type buffers;
k)   the possibility of two simultaneous acts of imprudence and/or the abuse of instructions for use.
l)   ambient temperature in the well and machinery spaces lower than +5 °C and higher than +40 °C;
m)   health and safety of animals.
However, this document can usefully be taken as a basis.
Noise and vibrations are not dealt with in this document as they are not considered a significant nor relevant hazard for the actual type of the accessible goods only lifts.
1.6   The requirements of this document are such that the possibility of a failure of an electric safety device or a safety component complying with all the requirements of this document needs not to be taken into consideration.
1.7   This document is not applicable to accessible goods only lifts which were manufactured before the date of its publication as EN.

  • Draft
    189 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1426:2024(Main)
Bitumens and bituminous binders - Determination of needle penetration
kSIST FprEN 1426:2024

This document specifies a method for the determination of the needle penetration of bitumens and bituminous binders.
The standard procedure for the determination of the needle penetration (consistency) is described for penetrations up to (330 × 0,1) mm at a temperature of 25 °C. The method also allows for penetrations up to (500 × 0,1) mm using a longer needle.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day