iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1710:2005+A1:2008/AC:2010

(Corrigendum)

Equipment and components intended for use in potentially explosive atmospheres in underground mines

Equipment and components intended for use in potentially explosive atmospheres in underground mines

TC - Correction to the English version only in Subclause 6.2.

Geräte und Komponenten für den Einsatz in schlagwettergefährdeten Bereichen von untertägigen Bergwerken

Appareils et composants destinés à être utilisés dans les mines souterraines grisouteuses

Oprema in komponente, namenjene za uporabo v potencialno eksplozivnih atmosferah v podzemnih rudnikih

Ta evropski standard določa zahteve za varovanje pred eksplozijami pri izgradnji in označevanju opreme, ki je lahko posamezni predmet ali konstrukcija.  To vključuje stroje in komponente, dane na trg s strani posameznega dobavitelja za uporabo v rudnikih, dovzetnih za eksplozivne atmosfere zaradi jamskega plina in/ali gorljivega prahu (pri atmosferskih pogojih, kot so opredeljeni v EN 1127-2).

General Information

Status
Withdrawn
Publication Date
17-Aug-2010
Withdrawal Date
20-Dec-2016
ICS
73.100.30 - Equipment for drilling and mine excavation
Technical Committee
CEN/TC 305 - Potentially explosive atmospheres - Explosion prevention and protection
Drafting Committee
CEN/TC 305/WG 5 - Equipment and protection systems for mining
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Dec-2016
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
2014/34/EU - Directive 2014/34/EU Of The European Parliament And Of The Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to equipment and protective systems intended for use in potentially explosive atmospheres (recast)
94/9/EC - Directive 94/9/EC of the European Parliament and the Council of 23 March 1994 on the approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres
98/37/EC - Machinery
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 1710:2006+A1:2008/AC:2010 - Equipment and components intended for use in potentially explosive atmospheres in underground mines

Relations

Replaced By
EN ISO/IEC 80079-38:2016 - Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38:2016)
Effective Date
28-Dec-2016
Corrects
EN 1710:2005+A1:2008 - Equipment and components intended for use in potentially explosive atmospheres in underground mines
Effective Date
08-Jun-2022

Buy Standard

EN 1710:2006+A1:2008/AC:2010EN 1710:2006+A1:2008/AC:2010
PreviousNext
Corrigendum
EN 1710:2006+A1:2008/AC:2010
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Oprema in komponente, namenjene za uporabo v potencialno eksplozivnih atmosferah v podzemnih rudnikihGeräte und Komponenten für den Einsatz in schlagwettergefährdeten Bereichen von untertägigen BergwerkenAppareils et composants destinés à être utilisés dans les mines souterraines grisouteusesEquipment and components intended for use in potentially explosive atmospheres in underground mines73.100.30Oprema za vrtanje in izkopavanjeEquipment for drilling and mine excavationICS:Ta slovenski standard je istoveten z:EN 1710:2005+A1:2008/AC:2010SIST EN 1710:2006+A1:2008/AC:2010en01-oktober-2010SIST EN 1710:2006+A1:2008/AC:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1710:2005+A1:2008/AC
August 2010
Août 2010
August 2010 ICS 73.100.30 English version Version Française Deutsche Fassung
Equipment and components intended for use in potentially explosive atmospheres in underground mines
Appareils et composants destinés à être utilisés dans les mines souterraines grisouteuses
Geräte und Komponent
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO/IEC 80079-38:2016(Main)
Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38:2016)
SIST EN ISO/IEC 80079-38:2017

ISO/IEC 80079-38:2016 is published as a dual logo standard and specifies the explosion protection requirements for the design, construction, assessment and information for use (maintenance, repair, marking) of equipment that may be an individual item or form an assembly. This includes machinery and components for use in mines susceptible to explosive atmospheres of firedamp and/or combustible
dust. The standard atmospheric conditions (relating to the explosion characteristics of the atmosphere) under which it may be assumed that equipment can be operated are:
- temperature -20 °C to 60 °C;
- pressure 80 kPa (0,8 bar) to 110 kPa (1,1 bar);
- and air with normal oxygen content, typically 21 % v/v. This part of ISO/IEC 80079 applies for equipment and components according to EPL Mb to be used in explosive atmospheres containing firedamp and/or combustible dust. For equipment and components according to EPL Ma, the requirements of this standard and of ISO 80079-36 and IEC 60079-0 apply. It is necessary to take account of external  
conditions to the equipment which may affect the hazard and the resultant protection measures. These measures may include ventilation, gas detection or gas drainage. This part of ISO/IEC 80079 also deals with the prevention of ignitions of explosive atmospheres caused by burning (or smouldering) of combustible material such as fabric fibres, plastic "O"-rings, rubber seals, lubricating oils or greases used in the construction of the equipment if such items could be an ignition source. For example, the mechanical failure of rotating shaft bearings can result in frictional heating that ignites its plastic cage, plastic seal or lubricating grease. Detailed requirements and test procedures for the fire protection of conveyer belts are not part of this part of ISO/IEC 80079.         Keywords: explosive atmospheres in underground mines, combustible dust

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19225:2017/A1:2019(Amendment)
Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems - Amendment 1 (ISO 19225:2017/Amd 1:2019)
SIST EN ISO 19225:2018/A1:2020

2019-09-17 JF: TC request for the editorial change in Annex ZA to adress the Consultant's comment
2019-03-19 The Enquiry draft of the standard had not been submitted for the assessment. In February, the TC provided a detailed Annex ZA  in line with the general EC request. CCMC requested the missing assessment on 2019-03-19. The indicative deadline to receive it is 2019-04-24.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19225:2017(Main)
Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems (ISO 19225:2017)
SIST EN ISO 19225:2018

ISO 19225:2017 specifies safety requirements to minimize the hazards listed in Clause 4 that can occur during the assembly, use, maintenance, repair, decommissioning, disassembly and disposal of shearer loaders and plough systems when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, in underground mining.
ISO 19225:2017 does not cover any hazards resulting from explosive atmospheres. Requirements for explosive atmospheres can be found in ISO/IEC 80079‑38.
ISO 19225:2017 is not applicable to machines that are manufactured before the date of its publication.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/IEC 80079-38:2016(Main)
Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38:2016)
SIST EN ISO/IEC 80079-38:2017

ISO/IEC 80079-38:2016 is published as a dual logo standard and specifies the explosion protection requirements for the design, construction, assessment and information for use (maintenance, repair, marking) of equipment that may be an individual item or form an assembly. This includes machinery and components for use in mines susceptible to explosive atmospheres of firedamp and/or combustible
dust. The standard atmospheric conditions (relating to the explosion characteristics of the atmosphere) under which it may be assumed that equipment can be operated are:
- temperature -20 °C to 60 °C;
- pressure 80 kPa (0,8 bar) to 110 kPa (1,1 bar);
- and air with normal oxygen content, typically 21 % v/v. This part of ISO/IEC 80079 applies for equipment and components according to EPL Mb to be used in explosive atmospheres containing firedamp and/or combustible dust. For equipment and components according to EPL Ma, the requirements of this standard and of ISO 80079-36 and IEC 60079-0 apply. It is necessary to take account of external  
conditions to the equipment which may affect the hazard and the resultant protection measures. These measures may include ventilation, gas detection or gas drainage. This part of ISO/IEC 80079 also deals with the prevention of ignitions of explosive atmospheres caused by burning (or smouldering) of combustible material such as fabric fibres, plastic "O"-rings, rubber seals, lubricating oils or greases used in the construction of the equipment if such items could be an ignition source. For example, the mechanical failure of rotating shaft bearings can result in frictional heating that ignites its plastic cage, plastic seal or lubricating grease. Detailed requirements and test procedures for the fire protection of conveyer belts are not part of this part of ISO/IEC 80079.         Keywords: explosive atmospheres in underground mines, combustible dust

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12299:2024(Main)
Railway applications - Ride comfort for passengers - Measurement and evaluation
SIST EN 12299:2024

The purpose of this document is to provide methods for quantifying the ride comfort of a passenger in a rail vehicle in response to the track sections it is operated over.
The methods aim to quantify the effects of vehicle body motions on ride comfort and to make the assessment of passenger comfort predictable, repeatable, objective and meaningful.
The methods and comfort scales are validated for people of good health.
This document applies to passengers in rail vehicles operating on heavy rail networks.
This document applies to measurements of motions. It also applies to simulated motions. Guidance is provided on:
-   which method described within the document should be used for different scenarios;
-   typical values for different comfort levels;
-   the application of simulation.
This document excludes health and safety issues, non-passenger carrying vehicles, vehicle homologation and safety, limit values, motion sickness, discomfort caused by accelerating and braking, design guidelines and measurement technology.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-4:2024(Main)
Paints and varnishes - Wettability - Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension (ISO 19403-4:2024)
kSIST FprEN ISO 19403-4:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids from an interfacial tension with optical methods. The method can be applied for the characterization of liquid coating materials, especially if drying effects occur during alternative measurement. If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17966:2024(Main)
Fire protection equipment - Carbon dioxide extinguishing systems for use on premises - Design and installation (ISO 6183:2022, modified)
SIST EN 17966:2024

This document specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of fixed carbon dioxide firefighting systems in buildings, plants or other structures. It is not applicable to extinguishing systems on ships, in aircraft, on vehicles or on mobile fire appliances, or to below ground systems in the mining industry; nor does it apply to carbon dioxide pre-inerting systems.
Design of systems where unclosable opening(s) of the protected volume exceed a specified area and where the opening(s) can be subject to the effect of wind is not specified, although general guidance on the procedure to be followed in such cases is given (see 7.4.3.2).

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TR 15235:2024(Main)
Preparation of steel substrates before application of paints and related products - Collected information on the effect of levels of water-soluble salt contamination (ISO/TR 15235:2001)
kSIST-TP FprCEN ISO/TR 15235:2024

This Technical Report provides information on the effect of water-soluble chloride and sulfate contamination levels on steel surfaces, before the application of paint or related products to surfaces prepared in accordance with standard mechanical or blast-cleaning surface preparation methods.
NOTE The tolerance for water-soluble salt contamination may be different for different paint types.
This information may be used when evaluating the adequacy of surface preparation prior to painting.
This document is concerned only with measured levels of salt contamination based upon either laboratory or field testing. The levels of soluble chloride and sulfate discussed in this document are to be compared using soluble surface densities of the species as determined after extraction in accordance with ISO 8502-6 (the Bresle method), or other methods giving equivalent results. Total soluble-salt contamination may be determined by conductometric testing, but such testing will not determine the nature and concentration of the specific salts present, e.g. whether chloride or sulfate is present, or its concentration.
This document does not define specific levels of cleanliness or methods of salt removal.

  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 509:2024(Main)
Decorative fuel-effect gas appliances
kSIST FprEN 509:2024

This document specifies the requirements and test methods for the construction, safety, and marking of decorative fuel effect gas appliances not exceeding a nominal heat input of 20 kW (based on the net calorific value), thereafter referred to as appliances.
This document is applicable to appliances that are designed to simulate a solid fuel fire and incorporate a natural draught burner with or without an ignition burner, that uses one or more combustible gases of the three gas families at the pressures stated in EN 437:2021. The appliances are for decorative purposes only and are not heating appliances.
This document is applicable to type BAS, as described in 4.2, decorative fuel effect gas appliances that are designed to be installed within a non-combustible builder's opening or a non-combustible fireplace recess.
NOTE 1   This document specifies special national conditions in Annex C for appliances of category I2E+, marketed in Belgium.
NOTE 2   This document specifies special A-deviations in Annex D for appliances in Switzerland which require additional requirements for subclauses 6.6 and 6.7.
This document includes additional requirements for Type BBS appliances which are specified in Annex F.
In addition, this document is applicable to decorative fuel-effect gas appliances that are designed to be installed under a non-combustible canopy which is independent or integral with a flue box, for which additional requirements are specified in Annex A.
The use of toxic gases is not covered.
This document is not applicable to:
-   catalytic combustion appliances;
-   appliances in which the supply of combustion air and/or the evacuation of products of combustion is achieved by mechanical means.
NOTE 3   Requirements concerning the rational use of energy have not been included in this document, because the appliances are for decorative purposes.

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day