EN ISO 19225:2017/A1:2019

SLOVENSKI STANDARD
01-april-2020
Stroji za podzemne rudnike - Premični rudarski stroji na odkopu - Varnostne
zahteve za valjčne nakladalne stroje in sisteme s plugom - Dopolnilo A1 (ISO
19225:2017/Amd 1:2019)
Underground mining machines - Mobile extracting machines at the face - Safety
requirements for shearer loaders and plough systems - Amendment 1 (ISO
19225:2017/Amd 1:2019)
Underground mining machines - Mobile extracting machines at the face - Safety
requirements for shearer loaders and plough systems - Amendment 1 (ISO
19225:2017/Amd 1:2019)
Machines d'exploitation de mines et carrières souterraines - Machines mobiles
d'abattage de front de taille - Exigences de sécurité imposées aux haveuses à tambour
(s) et aux rabots - Amendement 1 (ISO 19225:2017/Amd 1:2019)
Ta slovenski standard je istoveten z: EN ISO 19225:2017/A1:2019
ICS:
73.100.30 Oprema za vrtanje in Equipment for drilling and
izkopavanje mine excavation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19225:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 73.100.30
English Version
Underground mining machines - Mobile extracting
machines at the face - Safety requirements for shearer
loaders and plough systems - Amendment 1 (ISO
19225:2017/Amd 1:2019)
Machines d'exploitation de mines et carrières Bergbaumaschinen unter Tage - Mobile
souterraines - Machines mobiles d'abattage de front de Abbaumaschinen im Streb - Sicherheitsanforderungen
taille - Exigences de sécurité imposées aux haveuses à für Walzenlader und Hobelanlagen - Änderung 1 (ISO
tambour(s) et aux rabots - Amendement 1 (ISO 19225:2017/Amd 1:2019)
19225:2017/Amd 1:2019)
This amendment A1 modifies the European Standard EN ISO 19225:2017; it was approved by CEN on 29 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19225:2017/A1:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 19225:2017/A1:2019) has been prepared by Technical Committee ISO/TC 82
"Mining" in collaboration with Technical Committee CEN/TC 196 “Mining machinery and equipment -
Safety” the secretariat of which is held by DIN.
This Amendment to the European Standard EN ISO 19225:2017 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by April 2020, and
conflicting national standards shall be withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19225:2017/Amd 1:2019 has been approved by CEN as EN ISO 19225:2017/A1:2019
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request M/396
(Machinery) to provide one voluntary means of conforming to essential requirements of Directive
2006/42/EC (MD).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC (MD)
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2006/42/EC (MD) this EN
1.1.2.  Principles of safety 5.4.1; 5.13; 6; 7.3.5
integration
1.1.3.  Materials and products 5.10.1
1.1.5.  Design of machinery to 5.12; 7.3.2
facilitate its handling
1.1.6.  Ergonomics 5.4.3.1; 5.4.5; 5.4.6
1.1.7.  Operating positions 5.4.5; 5.4.6
1.2.1.  Safety and reliability of 5.4.2; 5.4.3; 5.4.3.1; 5.4.3.5;
control systems 5.4.6; 5.4.8; 5.4.8.2; 5.4.8.3
1.2.2.  Control devices 5.4.1; 5.4.3; 5.4.3.1; 5.4.3.4;
5.4.3.5.3; 5.4.5; 5.4.6
1.2.3.  Starting 5.4.3; 5.4.3.3; 5.4.3.5.3; 5.4.7
1.2.4.1.  Normal stop 5.4.3; 5.4.3.5.1
1.2.4.2.  Operational stop 5.4.3.5.3
1.2.4.3.  Emergency stop 5.4.3.5.3; 5.4.5; 5.4.6; 5.4.7
1.2.4.4.  Assembly of 5.4.3.5.3
machinery
1.2.5.  Selection of control or 5.4.3; 5.4.3.1; 7.3.6
operating modes
1.2.6.  Failure of the power 5.4.3; 5.4.3.5; 5.4.4; 5.4.8.3; 5.5
supply
1.3.1.  Risk of loss of stability 5.3; 5.12; 7.3
1.3.2.  Risk of break-up during 5.9; 5.10; 7.3.6
operation
1.3.3.  Risks due to falling or 5.5
ejected objects
1.3.4.  Risks due to surfaces, 5.2.1; 5.9.1
edges
or angles
1.3.7.  Risks related to moving 5.9.1; 7.2
parts
1.3.8.1.  Moving transmission 5.9
parts
1.3.8.2.  Moving parts involved 5.9
in the process
1.3.9.  Risks of uncontrolled 5.4.8.2; 5.4.8.3
movements
1.4.1.  General requirements 5.9
1.4.2.1.  Fixed guards 5.9
1.5.1.  Electricity supply 5.4.3; 5.8
1.5.4.  Errors of fitting 5.8; 5.9; 5.10; 7
1.5.5.  Extreme temperatures 5.2.2; 5.9.3; 5.10.1
1.5.6.  Fire 5.11
1.5.8.  Noise 5.7.2; A
1.5.13.  Emissions of hazardous 5.6.2; 5.6.3
materials and
substances
1.6.1.  Machinery maintenance 5.10.1; 5.13; 73.6
1.6.2.  Access to operating 5.13
positions and servicing
points
1.6.3.  Isolation of energy 5.4.3.2; 5.4.8.5; 5.8.2
sources
1.6.4.  Operator intervention 5.4.3.1
1.7.1.  Information and 7.2
warnings on the
machinery
1.7.1.1.  Information and 5.4.3; 7.3.5
information devices
1.7.1.2.  Warning devices 5.4.3; 5.4.3.4;
1.7.2.  Warning of residual 7.2
risks
1.7.3.  Marking of machinery 5.12; 7.3.1; 7.3.5; 7.3.6; 7.4
1.7.4.  Instructions 7.3; 7.3.6
1.7.4.1.  General principles for 7.3
the drafting of
instructions
1.7.4.2.  Contents of the 7.3.1; 7.3.2; 7.3.3; 7.3.4; 7.3.5;
instructions 7.3.6; A1
3.3  Control systems 5.4.3; 5.4.5; 5.4.6
3.3.3.  Travelling function 5.4.5
3.3.4.  Movement of pedestrian 5.4; 5.4.6
controlled machinery
3.5.2.  Fire 5.11
3.6.1.  Signs, signals and 5.4.3.1; 5.4.3.4; 5.4.5; 7.2
warnings
3.6.2.  Marking 7.4
5.5.  Fire 5.4.8.2
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journ
...