EN ISO 19879:2005
(Main)Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2005)
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2005)
Migrated from Progress Sheet (TC Comment) (2000-07-10): ISO/TC 131/SC4 Secretary (Ms. Boehme)informed us that the revision of ISO 8434- ++ 5:1995 is given a new number "ISO/CD 19879"(SJ/000406)
Metallische Rohrverschraubungen für Fluidtechnik und allgemeine Anwendung - Prüfverfahren für hydraulische Rohrverschraubungen in der Fluidtechnik (ISO 19879:2005)
Diese Internationale Norm legt einheitliche Verfahren für die Prüfung und die Bewertung von metallischen Rohrverbindungen, Einschraubzapfen und Flanschverbindungen für Hydraulikanwendungen fest. Diese Internationale Norm gilt nicht für die Prüfung von Hydraulik-Schnellkupplungen, die in ISO 7241-2 festgelegt ist.
Die in dieser Internationalen Norm festgelegten Prüfungen sind voneinander unabhängig und beschreiben das für die jeweilige Prüfung durchzuführende Verfahren; Prüfanforderungen und Leistungskriterien sind in der jeweiligen Internationalen Norm über das entsprechende Bauteil enthalten.
Für den Eignungsnachweis der Verbindungsteile muss die in dieser Internationalen Norm festgelegte Mindestanzahl an Proben einer Prüfung unterzogen werden, sofern in der entsprechenden Norm über die Verbindungsteile nichts anderes festgelegt ist oder zwischen Hersteller und Anwender vereinbart wurde.
Raccords de tubes métalliques pour transmissions hydrauliques et pneumatiques et applications générales - Méthodes d'essai pour raccords pour transmissions hydrauliques (ISO 19879:2005)
Kovinski cevni priključki za fluidno tehniko in splošno uporabo – Preskusne metode za hidravlične omrežne priključke (ISO 19879:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2005
.RYLQVNLFHYQLSULNOMXþNL]DIOXLGQRWHKQLNRLQVSORãQRXSRUDER±3UHVNXVQH
PHWRGH]DKLGUDYOLþQHRPUHåQHSULNOMXþNH,62
Metallic tube connections for fluid power and general use - Test methods for hydraulic
fluid power connections (ISO 19879:2005)
Metallische Rohrverschraubungen für Fluidtechnik und allgemeine Anwendung -
Prüfverfahren für hydraulische Rohrverschraubungen in der Fluidtechnik (ISO
19879:2005)
Raccords de tubes métalliques pour transmissions hydrauliques et pneumatiques et
applications générales - Méthodes d'essai pour raccords pour transmissions
hydrauliques (ISO 19879:2005)
Ta slovenski standard je istoveten z: EN ISO 19879:2005
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 19879
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2005
ICS 23.040.60; 23.100.40
English Version
Metallic tube connections for fluid power and general use - Test
methods for hydraulic fluid power connections (ISO 19879:2005)
Raccords de tubes métalliques pour transmissions Metallische Rohrverschraubungen für Fluidtechnik und
hydrauliques et pneumatiques et applications générales - allgemeine Anwendung - Prüfverfahren für hydraulische
Méthodes d'essai pour raccords pour transmissions Rohrverschraubungen in der Fluidtechnik (ISO 19879:2005)
hydrauliques (ISO 19879:2005)
This European Standard was approved by CEN on 31 July 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19879:2005: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 19879:2005) has been prepared by Technical Committee ISO/TC 131
"Fluid power systems" in collaboration with Technical Committee ECISS/TC 29 "Steel tubes and
fittings for steel tubes", the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2006, and conflicting national
standards shall be withdrawn at the latest by February 2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 19879:2005 has been approved by CEN as EN ISO 19879:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 19879
First edition
2005-08-01
Metallic tube connections for fluid power
and general use — Test methods for
hydraulic fluid power connections
Raccords de tubes métalliques pour transmissions hydrauliques et
pneumatiques et applications générales — Méthodes d'essai pour
raccords pour transmissions hydrauliques
Reference number
ISO 19879:2005(E)
©
ISO 2005
ISO 19879:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 19879:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 General requirements. 2
5 Repeated assembly test. 6
6 Leakage test. 6
7 Proof test. 7
8 Burst test. 8
9 Cyclic endurance test. 9
10 Vacuum test. 10
11 Overtightening test. 11
12 Vibration test. 11
13 Cyclic endurance (impulse) test with vibration.14
14 Identification statement (reference to this International Standard) . 15
Annex A (normative) Test data form . 16
Bibliography . 19
ISO 19879:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19879 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4,
Connectors and similar products and components.
This first edition of ISO 19879 cancels and replaces ISO 8434-5:1995, which has been technically revised.
iv © ISO 2005 – All rights reserved
ISO 19879:2005(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit. Components must be designed to meet these requirements under varying conditions. Testing
of components to meet performance requirements provides a basis of assurance for determining design
application and for checking component compliance with the stated requirements.
INTERNATIONAL STANDARD ISO 19879:2005(E)
Metallic tube connections for fluid power and general use —
Test methods for hydraulic fluid power connections
1 Scope
This International Standard specifies uniform methods for the testing and performance evaluation of metallic
tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. This
International Standard does not apply to the testing of hydraulic quick-action couplings, which is covered by
ISO 7241-2.
Tests outlined in this International Standard are independent of each other and document the method to follow
for each test. See the appropriate component International Standard for which tests to conduct and for
performance criteria.
For qualification of the connector, the minimum number of samples specified in this International Standard are
tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer
and the user.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and
100 IRHD)
ISO 3448, Industrial liquid lubricants — ISO viscosity classification
1)
ISO 3601-3, Fluid power systems — O-rings — Part 3: Quality acceptance criteria
1)
ISO 5598, Fluid power systems and components — Vocabulary
ISO 6508 (all parts), Metallic materials — Rockwell hardness test
ISO 6605, Hydraulic fluid power — Hoses and hose assemblies — Test methods
ISO 6743-4, Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H
(Hydraulic systems)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
1) Under revision.
ISO 19879:2005(E)
4 General requirements
WARNING — Some of the tests described in this International Standard are considered hazardous. It
is therefore essential that, in conducting these tests, all appropriate safety precautions be strictly
adhered to. Attention is drawn to the danger of burst, fine jets (which can penetrate the skin) and
energy release of expanding gases. To reduce the hazard of energy release, bleed air out of test
specimens prior to pressure testing. Tests shall be set up and performed by properly trained
personnel.
4.1 Test assemblies
All components tested shall be in the final form, including annealed nuts, as required for brazed components.
Unless otherwise specified in the respective connector standard, Type 1 test assemblies shall be as shown in
Figure 1 for tube connections (for repeated assembly, leakage, proof, burst and cyclic endurance tests), and
Type 2 test assemblies shall be as shown in Figure 2 for male stud ends (for leakage, proof and, if specified,
burst and cyclic endurance tests). Alternatively, in order to test the connector to its full capability, use of the
metallic tube may be omitted for burst and cyclic endurance tests, and different configurations with similar
cap
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.