iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN/TR 14819-2:2005

(Main)

Safety recommendations for cableway installations designed to carry persons - Prevention and fight against fire - Part 2: Other funicular railways and other installations

Safety recommendations for cableway installations designed to carry persons - Prevention and fight against fire - Part 2: Other funicular railways and other installations

This part of the technical report specifies safety recommendations applicable to the prevention and fighting of
fires in funicular railways not in tunnels, aerial ropeways and ski-tows that may endanger the health and safety
of persons.
With regard to funicular railways, these recommendations are applicable to those not running in a tunnel and
having a pathway alongside the track that does not allow passengers to exit the carrier in less than 5 min. For
funicular railways where evacuation of the carrier can be completed within 5 min, the same recommendations
may be applied in part according to the results of the safety analysis of the installation.
With regard to these problems of fire, it is essential to take organizational measures relating to operation, but
these are not covered in this report.
Requirements for aerial ropeways operating in a tunnel may also be based on CEN/TR 14819-1.

Sicherheitsempfehlungen für Seilbahnen für den Personenverkehr - Brandverhütung und -bekämpfung - Teil 2: Andere Standseil- und Seilbahnen

Recommandations de sécurité pour les installations à câbles transportant des personnes - Prévention et lutte contre les incendies - Partie 2 : Autres funiculaires et autres installations

La présente partie du rapport technique établit les recommandations de sécurité s'appliquant à la prévention et à la lutte contre l'incendie des funiculaires sans tunnel, des téléphériques et des téléskis pouvant mettre en danger la sécurité et la santé des personnes.
Concernant les funiculaires, ces recommandations sont applicables à ceux ne possédant pas de tunnel, et dont le cheminement le long de la voie ne permet pas une sortie des passagers du véhicule en moins de 5 minutes. Pour les funiculaires dont l'évacuation du véhicule se fait en moins de 5 minutes, les mêmes recommandations peuvent être appliquées en partie suivant les résultats de l'étude de sécurité de l'installation.
Vis à vis de ces problèmes d'incendie, il est nécessaire de prendre des mesures d'organisation qui relèvent de l'exploitation mais ceci n'est pas traité dans le présent rapport.
Les téléphériques fonctionnant en tunnel pourront aussi s'inspirer du CEN/TR 14819-1.

Varnostna priporočila za žičniške naprave za prevoz oseb – Preprečevanje in gašenje požara – 2. del: Ostale tirne vzpenjače in druge žičniške naprave

General Information

Status
Withdrawn
Publication Date
15-Nov-2005
Withdrawal Date
13-Nov-2018
ICS
13.220.20 - Fire protection
45.100 - Cableway equipment
Technical Committee
CEN/TC 242 - Safety requirements for passenger transportation by rope
Drafting Committee
CEN/TC 242 - Safety requirements for passenger transportation by rope
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
14-Nov-2018
Directive
00/9/EC - Cableway installations designed to carry persons
2000/9/EC - Directive 2000/9/EC of the European Parliament and of the Council of 20 March 2000 relating to cableway installations designed to carry persons
Mandate
M/300 - Mandate for standardisation addressed to CEN, CENELEC and ETSI in the field of Cableway installations designed to carry persons
Ref Project
SIST-TP CEN/TR 14819-2:2006 - Safety recommendations for cableway installations designed to carry persons - Prevention and fight against fire - Part 2: Other funicular railways and other installations

Relations

Replaced By
EN 17064:2018 - Safety requirements for cableway installations designed to carry persons - Prevention and fight against fire
Effective Date
08-Jun-2022

Buy Standard

TP CEN/TR 14819-2:2006TP CEN/TR 14819-2:2006
PreviousNext
Technical report
TP CEN/TR 14819-2:2006
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2006
9DUQRVWQDSULSRURþLOD]DåLþQLãNHQDSUDYH]DSUHYR]RVHE±3UHSUHþHYDQMHLQ
JDãHQMHSRåDUD±GHO2VWDOHWLUQHY]SHQMDþHLQGUXJHåLþQLãNHQDSUDYH
Safety recommendations for cableway installations designed to carry persons -
Prevention and fight against fire - Part 2: Other funicular railways and other installations
Sicherheitsempfehlungen für Seilbahnen für den Personenverkehr - Brandverhütung und
-bekämpfung - Teil 2: Andere Standseil- und Seilbahnen
Recommandations de sécurité pour les installations a câbles transportant des personnes
- Prévention et lutte contre les incendies - Partie 2 : Autres funiculaires et autres
installations
Ta slovenski standard je istoveten z: CEN/TR 14819-2:2005
ICS:
13.220.20 3RåDUQD]DãþLWD Fire protection
45.100 2SUHPD]DåLþQLFH Cableway equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL REPORT
CEN/TR 14819-2
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
November 2005
ICS 13.220.20; 45.100
English Version
Safety recommendations for cableway installations designed to
carry persons - Prevention and fight against fire - Part 2: Other
funicular railways and other installations
Recommandations de sécurité pour les installations à Sicherheitsempfehlungen für Seilbahnen für den
câbles transportant des personnes - Prévention et lutte Personenverkehr - Brandverhütung und -bekämpfung - Teil
contre les incendies - Partie 2 : Autres funiculaires et 2: Andere Standseil- und Seilbahnen
autres installations
This Technical Report was approved by CEN on 29 August 2005. It has been drawn up by the Technical Committee CEN/TC 242.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 14819-2:2005: E
worldwide for CEN national Members.

Contents Page
Foreword .4
Introduction.5
1 Scope.6
2 Normative references.6
3 Terms and definitions .7
4 General recommendations.8
4.1 Application of this technical report .8
4.2 Safety principles.8
4.2.1 General.8
4.2.2 Hazard scenarios.8
4.2.3 Safety measures.8
5 Basic recommendations .9
6 Recommendations concerning fire prevention and firefighting in carriers.10
6.1 Materials .10
6.2 Electrical cabinets.10
6.3 Cabling outside the electrical cabinets and lighting.11
6.4 Batteries.11
6.5 Battery chargers.11
6.6 Video equipment (camera, monitor) .11
6.7 Heating, air conditioning.11
6.8 Electrical components outside cabinets which are energized during travel (dynamos,
alternators, motors).11
6.9 Pantographs .12
6.10 Rail brake – Retarder.12
6.11 Hydraulic power plants and circuits – Pressure vessels – Refrigerants .12
6.12 Prohibition of smoking, open fires and the transportation of flammable materials.12
6.13 Extinguishers and other means of firefighting .12
6.14 Capacity of carriers.13
6.15 Recovery measures in the event of a fire on board a carrier .13
6.16 Emergency exits from carriers .13
7 Recommendations concerning fire prevention and firefighting in the area of the line.13
7.1 Rails and overhead catenaries supplying auxiliary electrical power to carriers.13
7.2 Transmission of electrical power along the track or supported by line support structures.14
7.3 Remote communication cable between carrier and control point .14
7.4 Transportation of flammable liquid along the funicular railway track .14
7.5 Track or route of line.14
8 Recommendations concerning fire prevention and firefighting in stations.15
8.1 General.15
8.2 Platform materials .15
8.3 Maintenance pit beneath carriers at the platform .16
8.4 Space adjacent to the platforms.16
8.5 Transmission of electrical power .16
8.6 Contacts for recharging the carrier batteries.16
8.7 Video equipment (camera, monitor) .16
8.8 Dispensing machines for use by passengers and other platform furniture.17
8.9 Prohibition of smoking, open fires and the transportation of flammable materials.17
8.10 Extinguishers.17
8.11 Smoke detection and clearing. 17
9 Recommendations concerning fire prevention and firefighting in the machine room and
electrical power system spaces. 17
9.1 Prevention. 17
9.2 Limitation of spread of fire. 17
10 Recommendations concerning fire prevention and firefighting in electrical supply spaces. 18
11 Recommendations concerning fire prevention and firefighting in the control room. 18
11.1 Civil engineering. 18
11.2 Spaces adjacent to the control point. 19
11.3 Electrical equipment. 19
11.4 Video monitors . 19
11.5 Space heating .19
11.6 Domestic utensils. 19
11.7 Furniture . 19
11.8 Putting safety devices out of service. 19
11.9 Personnel. 20
12 Lightning. 20
13 Training of personnel . 20
14 Maintenance. 20
Bibliography. 21

Foreword
This Technical Report (CEN/TR 14819-2:2005) has been prepared by Technical Committee CEN/TC 242
“Safety requirements for passenger transportation by rope”, the secretariat of which is held by AFNOR.
CEN/TR 14819 comprises the following parts presented under the general title of Safety recommendations for
cableway installations designed to carry persons - Prevention and fight against fire:
 Part 1: Funicular railways in tunnels
 Part 2: Other funicular railways and other installations
This technical report forms part of the standards programme approved by the CEN Technical Board (CEN/BT)
on safety requirements for cableway installations designed to carry persons:
1 Safety requirements for cableway installations designed to carry persons - Terminology
2 Safety requirements for cableway installations designed to carry persons - General requirements
3 Safety requirements for cableway installations designed to carry persons - Calculations
4 Safety requirements for cableway installations designed to carry persons - Ropes
5 Safety requirements for cableway installations designed to carry persons - Tensioning devices
6 Safety requirements for cableway installations designed to carry persons - Drive systems and other
mechanical equipment
7 Safety requirements for cableway installations designed to carry persons - Carriers
8 Safety requirements for cableway installations designed to carry persons - Electrical equipment other
than for drive systems
9 Safety requirements for cableway installations designed to carry persons - Civil engineering works
10 Safety requirements for cableway installations designed to carry persons – Pre-commissioning inspection,
maintenance and operational inspection and checks
11 Safety requirements for cableway installations designed to carry persons – Recovery and evacuation
12 Safety requirements for cableway installations designed to carry persons - Operation
13 Safety requirements for cableway installations designed to carry persons - Quality assurance
Together these form a series of standards regarding design, manufacture, construction, maintenance and
operation of all cableway installations designed to carry persons.

Introduction
This draft report has been prepared by a working group set up by TC 242 "Safety requirements for passenger
transportation by rope". It responds to a request by the European Commission and CEN and will be of use to
operators and designers of installations other than funicular railways in tunnels covered by CEN/TR 14819-1.
1 Scope
This part of the technical report specifies safety recommendations applicable to the pre
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17928-1:2024(Main)
Gas infrastructure - Injection stations - Part 1: General requirements
kSIST FprEN 17928-1:2024

This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13237:2024(Main)
Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
oSIST prEN 13237:2022

This document specifies terms and definitions (vocabulary) to be used in suitable standards dealing with equipment and protective systems intended for use in potentially explosive atmospheres within the scope of Directive 2014/34/EU.
NOTE   Terms and definitions avoid misunderstandings that are important in relation to the essential health and safety requirements of Directive 2014/34/EU.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
kSIST FprEN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2350:2024(Main)
Aerospace series - Circuit breakers - Technical specification
kSIST FprEN 2350:2024
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 927-15:2024(Main)
Paints and varnishes - Coating materials and coating systems for exterior wood - Part 15: Assessment of bleeding of coloured wood extractives through a coating by means of a water immersion test
kSIST-TS FprCEN/TS 927-15:2024

This document specifies a test method using water immersion test for assessing the bleeding of coloured wood extractives through a coating. Leachates of coated and uncoated wood are collected after the immersion procedure and their colour is compared. The colour of the coated wood before and after immersion tests is also compared. This document does not specify acceptance values for colour differences that can be tolerated and it is not applicable to staining caused by knots for which there is a different test method (see EN 927 7).
NOTE   The method has been developed for oak and chestnut wood and might be applicable for other wood substrates containing water soluble extractives.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2024)
kSIST FprEN ISO 19085-5:2024

This document specifies the safety requirements and measures for dimension saws (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to raise and lower the main saw blade and scoring saw blade;
b)       device to tilt the main saw blade and scoring saw blade for angled cutting in one or both directions;
c)        device for scoring;
d)       device for grooving with milling tool with a width not exceeding 20 mm;
e)       demountable power feed unit;
f)         power-operated sliding table;
g)       workpiece clamping.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16186-6:2024(Main)
Railway applications - Driver's cab - Part 6: Integration of displays, controls and indicators for tram vehicles
kSIST FprEN 16186-6:2024

This document is applicable to vehicles operating on tram networks.
This document gives design requirements and guidance in order to ensure visibility and operability of displays, controls and indicators in the cab in all operating conditions (day, night, natural or artificial lighting).
It covers four aspects:
-   the characteristics of the displays, controls and indicators in order to ensure proper visibility: i.e. range of luminance and contrast as well as the possibility of adjustment of perceived brightness;
-   the requirements for the location of the displays, keyboards, controls and indicators in the cab and on the driver’s desk: i.e. position, angle of visibility, etc. with consideration of the normal driving position and the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.);
-   the characteristics and requirements for the location of microphones and loudspeakers;
-   design of symbols.
NOTE   All element numbers within the text refer to Table B.1.
This document does not apply to refurbishment of existing vehicles. This document is not intended to be applicable to driver's auxiliary desk, except for 5.3.13, Clause 6, 7.1.2, Clause 9 and Table B.1.

  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17450-2:2024(Main)
Fixed firefighting systems - Water mist systems - Part 2: Product characteristics and test methods for nozzles
kSIST FprEN 17450-2:2024

This document specifies product characteristics and test methods of open nozzles and automatic nozzles for use in water mist systems.
NOTE   All pressure data in this document are given as gauge pressures in bar.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17388-1:2024(Main)
Flexible sheets for waterproofing - Environmental product declarations - Product category rules for reinforced bitumen, plastic and rubber flexible sheets for roof waterproofing - Part 1: Cradle to grave and module D
kSIST FprEN 17388-1:2024

This document provides product category rules (PCR) for the assessment of the environmental performance of reinforced bitumen, plastic and rubber flexible sheets for which the intended use is roof waterproofing.
NOTE   The reference product standards are EN 13707 and EN 13956.
This document is intended to be used for the development and issue of a cradle to grave and module D EPD using:
-   either generic data and system generic data;
or
-   specific data and system specific data.
This document includes requirements and rules to:
-   define the indicators to be declared and the way in which they are collected and reported;
-   describe which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages;
-   include the rules for calculating the life cycle inventory (LCI) and the life cycle impact assessment (LCIA) underlying an EPD, including the specification of the quality of the applied data;
-   define generic data and system generic data which are to be used for an EPD.

  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17388-2:2024(Main)
Flexible sheets for waterproofing - Environmental product declarations - Product category rules for reinforced bitumen, plastic and rubber flexible sheets for roof waterproofing - Part 2: Cradle to gate with options, modules C1-C4 and module D
kSIST FprEN 17388-2:2024

This document provides product category rules (PCR) for the assessment of the environmental performance of reinforced bitumen, plastic and rubber flexible sheets for which the intended use is roof waterproofing.
NOTE   The reference product standards are EN 13707 and EN 13956.
This document is intended to be used for the development and issue of a cradle to gate with options, modules C1-C4 and module D EPD using specific data. This document includes requirements and rules to:
-   define the indicators to be declared and the way in which they are collected and reported;
-   describe which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages;
-   include the rules for calculating the life cycle inventory (LCI) and the life cycle impact assessment (LCIA) underlying an EPD, including the specification of the quality of the applied data.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day