iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1501-1:2011/FprA1

(Amendment)

Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

This European Standard applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2. This European Standard deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.This European Standard is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.This part 1 describes and defines the safety requirements of rear loaded RCV excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5.This European Standard is not applicable to:- operation in severe conditions e.g. extreme environmental conditions such as:- below - 25 °C and above + 40 °C temperatures;- tropical environment;- wind velocity in excess of 75 km/h;- contaminating environment;- corrosive environment;- operation in potentially explosive atmospheres;- handling of loads the nature of which could lead to dangerous situations (e.g. hot wastes, acids and bases, radioactive materials, contaminated waste, especially fragile loads, explosives);- operation on ships.This European Standard is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader

Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie 1 : Bennes à chargement arrière

Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za zbiranje odpadkov z nakladanjem zadaj

General Information

Status
Not Published
ICS
43.160 - Special purpose vehicles
Technical Committee
CEN/TC 183 - Waste management
Drafting Committee
CEN/TC 183/WG 2 - Waste collection vehicles and their associated lifting devices
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
03-Dec-2014
Due Date
27-Nov-2014
Completion Date
03-Dec-2014
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Ref Project
SIST EN 1501-1:2011/kFprA1:2014 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

Relations

Merged Into
EN 1501-1:2011+A1:2015 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
24-Dec-2014
Amends
EN 1501-1:2011 - Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
Effective Date
20-Mar-2013

Buy Standard

EN 1501-1:2011/kFprA1:2014EN 1501-1:2011/kFprA1:2014
PreviousNext
Draft
EN 1501-1:2011/kFprA1:2014
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2014
Vozila za zbiranje odpadkov - Splošne in varnostne zahteve - 1. del: Vozila za
zbiranje odpadkov z nakladanjem zadaj
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear
loaded refuse collection vehicles
Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine
Anforderungen und Sicherheitsanforderungen - Teil 1: Hecklader
Bennes de collecte des déchets - Exigences générales et exigences de sécurité - Partie
1 : Bennes à chargement arrière
Ta slovenski standard je istoveten z: EN 1501-1:2011/FprA1
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1501-1:2011
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
July 2014
ICS 43.160
English Version
Refuse collection vehicles - General requirements and safety
requirements - Part 1: Rear loaded refuse collection vehicles
Bennes de collecte des déchets - Exigences générales et Abfallsammelfahrzeuge und die dazugehörigen
exigences de sécurité - Partie 1 : Bennes à chargement Schüttungen - Allgemeine Anforderungen und
arrière Sicherheitsanforderungen - Teil 1: Hecklader
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 183.
This draft amendment A1, if approved, will modify the European Standard EN 1501-1:2011. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1501-1:2011/FprA1:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to Clause 2, Normative references .4
2 Modification to 5.2.3.3, Guide flap.4
3 Modifications to 5.2.3.6, Protective devices .4
4 Modifications to 5.10.3.1, Footboards .4
5 Modifications to 5.10.3.3, Provisions for footboard(s).5
6 Modification to 5.15.1, General .5
7 Modification to 7.1.1.2, Visual .5
8 Modifications to Annex B (normative), Open and closed systems – Footboard(s) .5

Foreword
This document (EN 1501-1:2011/FprA1:2014) has been prepared by Technical Committee CEN/TC 183
“Waste management”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1501-4:2023(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles
SIST EN 1501-4:2023

This document provides all of the information required in order to perform efficiently, and in standardized conditions, the determination, the declaration and the verification of noise emission values of refuse collection vehicles.
The document ensures the reproducibility of the determination of noise emission values within the limits established for the accuracy grade of the basic standard used to determine noise emission values.
This document specifies the noise measurement conditions for the types of RCVs defined and described in the standards of the EN 1501:2021 series.
This document applies to machines which are manufactured after the date of approval of this document by CEN.
Noise emissions of mobile waste and recycling containers are excluded.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-2:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles
SIST EN 1501-2:2021

This document applies to side loaded refuse collection vehicle (RCV), as defined in prEN 1501-1.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit for its intended function and can be operated, moved, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the side loaded RCV.
This document describes and defines the safety requirements of side loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s) including the loader cranes and the interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   below −25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-5:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles
SIST EN 1501-5:2021

This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting of other lifting devices so as to ensure that they are fitted for their function and can be operated, adjusted and maintained during their entire lifetime. It is not applicable to the end of life of the lifting devices.
This document describes and gives the safety requirements of the lifting devices for emptying refuse containers and their interfaces with the corresponding parts of the RCVs and will be used in conjunction with EN 1501 1:2021 for the rear, side and front loaded RCVs. It refers to EN 1501 4:2007 for the noise test code.
This document is not applicable to:
-   operation in severe conditions e.g. extreme environmental conditions such as:
-   temperatures below −20 °C and above +40 °C;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   lifting and transportation of persons;
-   emptying refuse containers other than those manufactured according to EN 840:2020 (all parts), EN 12574:2017 (all parts), EN 13071:2019 (all parts), and those described as paladin, diamond, skip containers;
-   loading bulky refuse by means of platform or forks;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships;
-   fitting and operation on stationary compactors.
This document is not applicable to machinery which is manufactured before the date of its publication by CEN.

  • Standard
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-1:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
SIST EN 1501-1:2021

This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated, adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.
This document describes and defines the safety requirements of rear loaded RCVs excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.
Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5. Safety requirements for loader cranes are defined in EN 12999.
This European Standard is not applicable to:
-   operation in severe conditions, e.g. extreme environmental conditions such as:
-   below -25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-3:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles
SIST EN 1501-3:2021

This document applies to a front loaded refuse collection vehicle (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV so as to ensure that it is fitted for its intended function and can be operated, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the front loaded RCV.
This document describes and defines the safety requirements of the front loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s), loader cranes and their interface to the RCV are defined in EN 1501 5:2021.
Safety requirements for loader cranes are defined in EN 12999:2020. Additional specific requirements to loader cranes installed on RCVs are defined in EN 1501 5:2021.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   operation in severe conditions, e.g. extreme environmental conditions such as:
-   below −20 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16815:2019(Main)
CleANopen - Application profile for municipal vehicles
SIST EN 16815:2019

This European Standard provides a set of CANopen application profile specifications that describes the CleANopen embedded body control network of municipal vehicles, e.g. refuse collecting trucks. It specifies the CANopen communication interfaces and the application functionality of several functional elements (virtual devices).
It does not specify CANopen devices. The CleANopen application profile specifications consist of several parts dealing with the following:
- general definitions;
- functionality of the virtual devices;
- pre defined PDOs and SDOs;
- application objects.

  • Standard
    979 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16596:2013(Main)
Electric-electronic interface between chassis-cab and bodywork of refuse collection vehicles (RCVs)
SIST-TP CEN/TR 16596:2014

This Technical Report proposes a standardized interface between the chassis-cab and the bodywork of refuse collection vehicles. The solution, initially for vehicles with hard wired interface and CAN interface, is developed into full CAN communication between the bodywork and the chassis-cab.

  • Technical report
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-1:1998/FprA2(Amendment)
Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 1: Rear-end loaded refuse collection vehicles
SIST EN 1501-1:2000/kFprA2:2009
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1501-2:2005/FprA1(Amendment)
Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles
SIST EN 1501-2:2005/kFprA1:2009
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1789:2020+A1:2023(Main + Amendment)
Medical vehicles and their equipment - Road ambulances
SIST EN 1789:2020+A1:2024

This European Standard specifies requirements for the design, testing, performance and equipping of road ambulances used for the transport, monitoring, treatment and care of patients. It contains requirements for the patient’s compartment in terms of the working environment, ergonomic design and the safety of the crew and patients.This European Standard does not cover the training of the staff which is the responsibility of the authority/authorities in the country where the ambulance is to be registered.
This European Standard is applicable to road ambulances capable of transporting at least one person on a stretcher and excludes the transportation of hospital beds.
This standard also specifies requirements for ambulances intended to carry transport incubator systems.
The European Standard covers the specific requirements of each type of road ambulance which are
designated according to the patient condition e.g. patient transport road ambulance types A1, A2, B and C.
This European Standard gives general requirements for medical devices carried in road ambulances and used therein and outside hospitals and clinics in situations where the ambient conditions can differ from normal indoor conditions.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day