EN ISO 377:1997

SLOVENSKI STANDARD
SIST EN ISO 377:1998
01-avgust-1998
Jeklo in jekleni izdelki - Mesto jemanja in priprava vzorcev ter preskušanci za
mehansko preskušanje (ISO 377:1997)
Steel and steel products - Location and preparation of samples and test pieces for
mechanical testing (ISO 377:1997)
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben
für mechanische Prüfungen (ISO 377:1997)
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour
essais mécaniques (ISO 377:1997)
Ta slovenski standard je istoveten z: EN ISO 377:1997
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.01 Železni in jekleni izdelki na Iron and steel products in
splošno general
SIST EN ISO 377:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 377:1998

---------------------- Page: 2 ----------------------

SIST EN ISO 377:1998

---------------------- Page: 3 ----------------------

SIST EN ISO 377:1998

---------------------- Page: 4 ----------------------

SIST EN ISO 377:1998

---------------------- Page: 5 ----------------------

SIST EN ISO 377:1998

---------------------- Page: 6 ----------------------

SIST EN ISO 377:1998
INTERNATIONAL
IS0
STANDARD
377
Second edition
1997-07-I 5
Steel and steel products - Location
and preparation of samples and test
pieces for mechanical testing
Acier et produits en acier -
Position et pkparation des khantiiions
et bprouvettes pour essais mkaniques
Reference number
IS0 377: 1997(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 377:1998
IS0 377:1997(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 377 was prepared by Technical Committee
ISO/TC 17, Steel, Subcommittee SC 20, Genera/ technical delivery
conditions, sampling and mechanical testing methods.
This second edition of IS0 377 cancels and replaces IS0 377~1:1989,
which has been technically revised.
Annex A forms an integral part of this International Standard.
0 IS0 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Internet central @ iso.ch
x.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 377:1998
INTERNATIONAL STANDARD @ IS0 IS0 377: 1997(E)
Steel and steel products - Location and preparation of samples
and test pieces for mechanical testing
II Scope
This International Standard specifies requirements for the identification, location and preparation of samples and
test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined
in IS0 6929. If agreed in the order this standard may also apply to other metallic products. It does not apply to non-
destructive tests.
These samples and test pieces are for use in tests which are carried out in conformity with the methods specified in
the product or material standard or, in the absence of this, in the test standard.
Where the requirements of the order or product standard differ from those given in this International Standard, then
the requirements of the order or product standard apply.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain
registers of currently valid International S
...