Founding - Ausferritic spheroidal graphite cast irons

This European Standard defines the grades and the corresponding requirements for ausferritic spheroidal graphite cast irons.
This European Standard specifies five grades of ausferritic spheroidal graphite cast iron by a classification based on mechanical properties measured on machined test pieces prepared from cast samples.
This European Standard also specifies two grades by a classification as a function of hardness.
This European Standard does not cover technical delivery conditions for iron castings, see EN 1559-1 [4] and EN 1559-3 [5].
NOTE   Grades given in Annex A are not intended for pressure equipment applications.

Gießereiwesen - Ausferritisches Gusseisen mit Kugelgraphit

Diese Europäische Norm definiert die Sorten und die entsprechenden Eigenschaften von ausferritischem Gusseisen mit Kugelgraphit. Diese Europäische Norm legt mittels einer auf mechanischen Eigenschaften basierenden Einteilung fünf Sorten von ausferritischem Gusseisen mit Kugelgraphit fest, wobei diese Eigenschaften an Proben bestimmt werden, die durch mechanische Bearbeitung aus Probestücken gewonnen wurden. Diese Europäische Norm legt außerdem zwei Sorten mittels einer Einteilung nach der Härte fest. Diese Europäische Norm enthält keine technischen Lieferbedingungen für Gussstücke aus Gusseisen, siehe EN 1559-1 [4] und EN 1559-3 [5]. ANMERKUNG Die im Anhang A aufgeführten Sorten sind nicht für Druckgeräte-Anwendungen bestimmt.

Fonderie - Fontes ausferritiques à graphite sphéroïdal

La présente Norme européenne définit les nuances et les exigences correspondantes des fontes
ausferritiques à graphite sphéroïdal.
La présente Norme européenne spécifie cinq nuances de fonte ausferritique à graphite sphéroïdal, en
établissant un classement basé sur leurs propriétés mécaniques, mesurées sur des éprouvettes usinées à
partir d’échantillons coulés.
La présente Norme européenne spécifie également deux nuances par un classement selon la dureté.
La présente norme européenne ne couvre pas les conditions techniques de fourniture des fontes, voir
l’EN 1559-1 [4] et l’EN 1559-3 [5].
NOTE Les nuances données dans l’Annexe A ne sont pas appropriées pour des applications relatives aux
équipements sous pression.

Livarstvo - Bainitno poboljšana duktilna litina

Ta evropski standard opredeljuje razrede in ustrezne zahteve za bainitno poboljšane duktilne litine. Ta evropski standard določa pet razredov bainitno poboljšanje duktilne litine s klasifikacijo na osnovi mehanskih lastnosti, izmerjenih na strojno obdelanih preskušancih, pripravljenih iz vzorcev litine. Ta evropski standard določa tudi dva razreda s klasifikacijo glede na trdoto. Ta standard ne zajema tehničnih dobavnih pogojev za železne ulitke, glej EN 1559-1 in EN 1559-3.

General Information

Status
Published
Publication Date
01-Nov-2011
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
10-Nov-2022

Relations

Buy Standard

Standard
EN 1564:2012
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Livarstvo - Bainitno poboljšana duktilna litinaGießereiwesen - Ausferritisches Gusseisen mit KugelgraphitFonderie - Fontes ausferritiques à graphite sphéroïdalFounding - Ausferritic spheroidal graphite cast iron77.140.80Železni in jekleni ulitkiIron and steel castingsICS:Ta slovenski standard je istoveten z:EN 1564:2011SIST EN 1564:2012en,fr,de01-januar-2012SIST EN 1564:2012SLOVENSKI
STANDARDSIST EN 1564:1998/A1:2006SIST EN 1564:19981DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1564
November 2011 ICS 77.080.10 Supersedes EN 1564:1997English Version
Founding - Ausferritic spheroidal graphite cast irons
Fonderie - Fontes ausferritiques à graphite sphéroïdal
Gießereiwesen - Ausferritisches Gusseisen mit Kugelgraphit This European Standard was approved by CEN on 24 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1564:2011: ESIST EN 1564:2012

Abrasion resistant grades of ausferritic spheroidal graphite cast iron . 21Annex B (informative)
Comparison of ausferritic spheroidal graphite cast iron material designations according to EN 1560 and ISO/TR 15931 [2] [7] . 23Annex C (informative)
Guidance values for tensile strength and elongation for test pieces machined from samples cut from a casting . 24Annex D (informative)
Guidance values for Brinell hardness . 25SIST EN 1564:2012

Determination of the hardness range . 26Annex F (informative)
Nodularity. 27Annex G (normative)
Sectioning procedure for cast samples . 28Annex H (informative)
Un-notched impact test . 29Annex I (informative)
Additional information on mechanical and physical properties . 31Annex J (informative)
Machinability of ausferritic spheroidal graphite cast irons . 33Annex K (informative)
Significant technical changes between this European Standard and the previous edition . 35Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 36Bibliography . 37 SIST EN 1564:2012
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.