SIST EN ISO 29862:2019

SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST EN 1939:2003
Samolepilni trakovi - Določevanje lastnosti prilepljivosti (ISO 29862:2018)
Self adhesive tapes - Determination of peel adhesion properties (ISO 29862:2018)
Klebebänder - Bestimmung der Klebkraft (ISO 29862:2018)
Rubans auto-adhésifs - Détermination des caractéristiques du pouvoir adhésif linéaire
(ISO 29862:2018)
Ta slovenski standard je istoveten z: EN ISO 29862:2019
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 29862
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 1939:2003
English Version
Self adhesive tapes - Determination of peel adhesion
properties (ISO 29862:2018)
Rubans auto-adhésifs - Détermination des Klebebänder - Bestimmung der Klebkraft (ISO
caractéristiques du pouvoir adhésif linéaire (ISO 29862:2018)
29862:2018)
This European Standard was approved by CEN on 8 April 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 29862:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 29862:2018 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 29862:2019 by
Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1939:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 29862:2018 has been approved by CEN as EN ISO 29862:2019 without any modification.

INTERNATIONAL ISO
STANDARD 29862
Second edition
2018-05
Self adhesive tapes — Determination
of peel adhesion properties
Rubans auto-adhésifs — Détermination des caractéristiques du
pouvoir adhésif linéaire
Reference number
ISO 29862:2018(E)
©
ISO 2018
ISO 29862:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 29862:2018(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Significance and use . 2
5 Method 1 — Self adhesive tapes — Measurement of peel adhesion from stainless
steel at an angle of 180° . 3
5.1 Principle . 3
5.2 Materials . 3
5.3 Apparatus . 3
5.4 Test samples and test pieces . 4
5.5 Procedure . 5
5.5.1 Standard test conditions . 5
5.5.2 Preparation of the panel . 5
5.5.3 Peel adhesion . 5
5.6 Expression of results . 5
5.7 Test report . 5
6 Method 2 — Self adhesive tapes — Measurement of peel adhesion from its own
backing at an angle of 180° . 6
6.1 Principle . 6
6.2 Apparatus . 6
6.3 Test samples and test pieces . 6
6.4 Procedure . 7
6.4.1 Standard test conditions . 7
6.4.2 Preparation of the panel . 7
6.5 Expression of results . 7
6.6 Test report . 7
7 Method 3 — Self adhesive tapes — Measurement of peel adhesion of double sided
and transfer tapes at an angle of 180° . 7
7.1 Principle . 7
7.2 Materials . 7
7.3 Apparatus . 7
7.4 Test samples and test pieces . 7
7.5 Procedure . 8
7.5.1 Standard test conditions . 8
7.5.2 Preparation of the panel . 8
7.5.3 Procedure for open side of double sided or adhesive transfer tape . 8
7.5.4 Procedure for closed side of double sided or adhesive transfer tape . 8
7.6 Expression of results . 8
7.7 Test report . 8
8 Method 4 — Self adhesive tapes — Measurement of adhesion of the liner to an
adhesive tape at an angle of 180° . 9
8.1 Principle . 9
8.1.1 Double sided adhesive tapes . 9
8.1.2 Single sided adhesive tapes . 9
8.2 Materials . 9
8.3 Apparatus . 9
8.4 Test samples and test pieces . 9
8.5 Procedure . 9
8.5.1 Double sided tapes . 9
8.5.2 Single sided tape . 9
8.6 Expression of results .10
ISO 29862:2018(E)
8.7 Test report .10
Annex A (normative) Self adhesive tapes — Measurement of peel adhesion from a surface
at low temperature .11
Annex B (normative) Self adhesive tapes — Measurement of peel adhesion from a surface
at an angle of 90° .12
Bibliography .14
iv © ISO 2018 – All rights reserved

ISO 29862:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This second edition cancels and replaces the first edition (ISO 29862:2007) of which it constitutes a
minor revision.
The changes compared to the previous edition are as follows:
— the normative references in Clause 2 have been updated;
— definitions have been added in Clause 3 for “self adhesive tape”, “liner” and “double sided
adhesive tape”;
— a Bibliography has been added;
— the text has been editorially revised to comply with the most recent editing rules.
INTERNATIONAL STANDARD ISO 29862:2018(E)
Self adhesive tapes — Determination of peel adhesion
properties
1 Scope
This document specifies a series of methods for the determination of peel adhesion properties of self
adhesives tapes.
This document contains:
— Method 1: Self adhesive tapes – Measurement of peel adhesion from stainless steel at an angle of 180°;
— Method 2: Self adhesive tapes – Measurement of peel adhesion from its own backing at an angle
of 180°;
— Method 3: Self adhesive tapes – Measurement of peel adhesion of double sided and transfer tapes at
an angle 180°;
— Method 4: Self adhesive tapes – Measurement of adhesion of the liner to an adhesive tape at an angle
of 180°.
Annexes A and B specify further variations in the testing protocol according to specific conditions.
A guide to the use of these methods is given in Table 1.
Table 1 — Methods and annexes
Method Angle of peel Temperature of test
23 °C Low temperature
Method 1 180° — Annex A
Adhesion to steel 90° Annex B -
Method 2 180° — Annex A
Adhesion to back- 90° Annex B —
ing
Method 3 180° — Annex A
Adhesion of 90° Annex B —
double sided and
transfer tape
Method 4 180° — Annex A
Adhesion of liner 90° Annex B -
NOTE 1 These methods provide a means of assessing the uniformity of the adhesion of a
given type of self adhesive tape. The assessment may be within a roll of tape, between rolls
or between production lots.
NOTE 2 Variations in the tape backing and adhesive affect the response. Therefore these
methods cannot be used to pinpoint the specific cause(s) of non uniformity.
NOTE 3 These test methods may not be appropriate to test tapes having either relatively
stiff backings, stiff liners or backing showing high stretch at low forces. These characteristics
will result in a high variability for the test response which is not a true indication of the real
nature of the adhesive bond.
ISO 29862:2018(E)
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12481, Self adhesive tapes — Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12481 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
3.1
peel adhesion
force required to peel a strip of adhesive tape from a specified substrate at a specified angle and speed
3.2
open side
surface of the adhesive on a double sided tape which is exposed on normal unwinding or
separation of the first liner
3.3
closed side
surface of the adhesive on a double sided tape which normally remains in contact with the
release liner on normal unwinding or separation of the first liner
3.4
transfer tape
adhesive tape having two available pressure sensitive surfaces without the need for a carrier and with
a release liner separating the adhesive surfaces. The adhesive may contain reinforcing material
3.5
self adhesive tape
pressure sensitive adhesive
adhesive which in a dry state is permanently tacky at room temperature and adheres readily to surfaces
under brief and light pressure
3.6
...