SIST EN ISO 29862:2025

SLOVENSKI STANDARD
01-februar-2025
Samolepilni trakovi - Določevanje lastnosti prilepljivosti (ISO 29862:2024)
Self adhesive tapes - Determination of peel adhesion properties (ISO 29862:2024)
Klebebänder - Bestimmung der Klebkraft (ISO 29862:2024)
Rubans auto-adhésifs - Détermination des caractéristiques de la force de pelage
(pouvoir adhésif linéaire) (ISO 29862:2024)
Ta slovenski standard je istoveten z: EN ISO 29862:2024
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 29862
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2024
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN ISO 29862:2019
English Version
Self adhesive tapes - Determination of peel adhesion
properties (ISO 29862:2024)
Rubans auto-adhésifs - Détermination des Klebebänder - Bestimmung der Klebkraft (ISO
caractéristiques de la force de pelage (pouvoir adhésif 29862:2024)
linéaire) (ISO 29862:2024)
This European Standard was approved by CEN on 9 December 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 29862:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 29862:2024) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2025, and conflicting national standards shall be
withdrawn at the latest by June 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 29862:2019.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 29862:2024 has been approved by CEN as EN ISO 29862:2024 without any modification.

International
Standard
ISO 29862
Third edition
Self adhesive tapes —
2024-12
Determination of peel adhesion
properties
Rubans auto-adhésifs — Détermination des caractéristiques de la
force de pelage (pouvoir adhésif linéaire)
Reference number
ISO 29862:2024(en) © ISO 2024
ISO 29862:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 29862:2024(en)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Significance and use . 2
5 Method 1 — Self adhesive tapes — Measurement of peel adhesion from stainless steel
at an angle of 180° . 3
5.1 Principle .3
5.2 Materials .3
5.3 Apparatus .4
5.3.1 Test piece cutter .4
5.3.2 Tensile testing machine .4
5.3.3 Stainless steel panels . . .4
5.3.4 Roller mechanically or hand operated .4
5.3.5 Light hand roller .4
5.4 Test samples and test pieces .4
5.5 Procedure .5
5.5.1 Standard test conditions .5
5.5.2 Preparation of the panel .5
5.5.3 Peel adhesion .5
5.6 Expression of results . .6
5.7 Test report .6
6 Method 2 — Self adhesive tapes — Measurement of peel adhesion from its own backing
at an angle of 180° . 6
6.1 Principle .6
6.2 Apparatus .7
6.2.1 Test piece cutter .7
6.2.2 Tensile testing machine .7
6.2.3 Suitable panels .7
6.2.4 Roller mechanically or hand operated .7
6.3 Test samples and test pieces .7
6.4 Procedure .7
6.4.1 Standard test conditions .7
6.4.2 Preparation .7
6.5 Expression of results . .7
6.6 Test report .7
7 Method 3 — Self adhesive tapes — Measurement of peel adhesion of double-sided and
transfer tapes at an angle of 180° . 8
7.1 Principle .8
7.2 Materials .8
7.3 Apparatus .8
7.4 Test samples and test pieces .8
7.5 Procedure .8
7.5.1 Standard test conditions .8
7.5.2 Preparation of the panel .8
7.5.3 Procedure for open side of double-sided or adhesive transfer tape .8
7.5.4 Procedure for closed side of double-sided or adhesive transfer tape .9
7.6 Expression of results .9
7.7 Test report .9
8 Method 4 — Self adhesive tapes — Measurement of adhesion of the liner to an adhesive
tape at an angle of 180° . 9
8.1 Principle .9

iii
ISO 29862:2024(en)
8.1.1 Double-sided adhesive tapes .9
8.1.2 Single sided adhesive tapes .9
8.2 Materials .9
8.3 Apparatus .9
8.4 Test samples and test pieces .9
8.5 Procedure .10
8.5.1 Double-sided tapes .10
8.5.2 Single sided tape .10
8.6 Expression of results . .10
8.7 Test report .10
Annex A (normative) Self adhesive tapes — Measurement of peel adhesion from a surface at
low temperature .11
Annex B (normative) Self adhesive tapes — Measurement of peel adhesion from a surface at an
angle of 90° .12
Bibliography . 14

iv
ISO 29862:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 193,
Adhesives, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This third edition cancels and replaces the second edition (ISO 29862:2018), which has been technically
revised.
The main changes are as follows:
— the normative references in Clause 2 have been updated;
— definitions have been added in Clause 3 for “test piece”, “test sample”, “backing” and “carrier”;
— Clause 4 has been modified to improve clarity and precision;
— the list of solvents in 5.2.2 has been revised;
— the description of the cutting device in 5.3.1 has been amended;
— the description of the procedure for preparing the peel test specimens has been revised, taking into
account occupational safety and practicability;
— the light hand roller was added in 5.3.5;
— conditioning time of 16 h was added in 5.4.1;
— inconsistencies have been removed in Clause 8;
— the text has been editorially revised to comply with the most recent principles and rules for the structure
and drafting.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

v
International Standard ISO 29862:2024(en)
Self adhesive tapes — Determination of peel adhesion
properties
1 Scope
This document specifies a series of methods for the determination of peel adhesion properties of self
adhesives tapes.
This document specifies:
— Method 1: Self adhesive tapes – Measurement of peel adhesion from stainless steel at an angle of 180°;
— Method 2: Self adhesive tapes – Measurement of peel adhesion from its own backing at an angle of 180°;
— Method 3: Self adhesive tapes – Measurement of peel adhesion of double-sided and transfer tapes at an
angle 180°;
— Method 4: Self adhesive tapes – Measurement of adhesion of the liner to an adhesive tape at an angle of 180°.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 12481, Self adhesive tapes — Terminology
EN 10088-2, Stainless steels — Part 2: Technical delivery conditions for sheet/plate and strip of corrosion
resisting steels for general purposes
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12481 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
peel adhesion
force required to peel a strip of adhesive tape from a specified substrate at a specified angle and speed
3.2
open side
surface of the adhesive on a double-sided adhesive tape which is exposed on normal unwinding
or separation of the first liner
[SOURCE: EN 12481:2000, 2.1.2.21]

ISO 29862:2024(en)
3.3
closed side
surface of the adhesive on a double-sided adhesive tape which remains in contact with the
release liner on normal unwinding or separation of the first liner
[SOURCE: EN 12481:2000, 2.1.2.10]
3.4
transfer tape
adhesive tape having two available pressure sensitive surfaces without the need for a carrier and with a
release liner separating the adhesive surfaces
Note 1 to entry: The adhesive may contain reinforcing material.
3.5
self adhesive tape
pressure sensitive adhesive
adhesive which in a dry state is permanently tacky at room temperature and adheres readily to surfaces
under brief and light pressure
3.6
liner
treated sheet to cover the adhesive temporarily to facilitate handling or unrolling
3.7
double-sided adhesive tape
tape where adhesive is applied to both sides of the carrier
3.8
test piece
strip of adhesive tape used for the peel test
3.9
test sample
sample of an adhesive tape, e.g. a roll or a sheet from which the test piece i
...