SIST EN 302 617 V2.2.1:2018
(Main)Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document specifies technical characteristics and methods of measurements for DSB AM ground based
transmitters, receivers and transceivers operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.1] as well as essential requirements under the Single
European Sky (SES) Interoperability Regulation No 552/2004 [i.3] and related implementing rules and/or essential
requirements under the EASA basic Regulation No 216/2008 [i.5] as amended by Regulation No 1108/2009 [i.6] may
apply to equipment within the scope of the present document.
Talni UHF radijski oddajniki, sprejemniki in sprejemniki-oddajniki za UHF aeronavtično mobilno storitev, ki uporablja amplitudno modulacijo - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument določa tehnične lastnosti in metode merjenja za talne oddajnike DSB AM, sprejemnike in sprejemnike-oddajnike, ki delujejo v celotnem aeronavtičnem frekvenčnem pasu med 225 MHz in 399,975 MHz ali kateremkoli njegovem delu.
Ta dokument zajema bistvene zahteve člena 3.2 Direktive 2014/53/EU [i.1] pod pogoji iz dodatka A.
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena Direktive 2014/53/EU [i.1], in tudi bistvene zahteve iz Uredbe o interoperabilnosti enotnega evropskega neba 552/2004 [i.5] ter zadevna izvedbena pravila in/ali bistvene zahteve iz osnovne Uredbe EASA št. 216/2008 [i.5], kakor je bila spremenjena z Uredbo št. 1108/2009 [i.6].
General Information
Standards Content (Sample)
Draft ETSI EN 302 617 V2.2.0 (2017-05)
HARMONISED EUROPEAN STANDARD
Ground-based UHF radio transmitters,
receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
2 Draft ETSI EN 302 617 V2.2.0 (2017-05)
Reference
REN/ERM-TGAERO-50
Keywords
aeronautical, AM, DSB, harmonised standard,
radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 302 617 V2.2.0 (2017-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 8
4 General requirements . 8
4.1 Frequency control . 8
4.2 Controls and indicators . 9
4.3 Class of emission and modulation characteristics . 9
4.4 Warm up . 9
4.5 Protection of the transmitter . 9
4.5.1 Definition . 9
4.5.2 Method of measurement . 9
4.5.3 Requirement . 9
5 General conditions of measurement . 9
5.1 Transmitter test signal arrangement . 9
5.1.1 Coaxial termination. 9
5.1.2 Signal sources . 10
5.1.3 Normal test signal . 10
5.2 Receiver test signal arrangement . 10
5.2.1 Test signal sources . 10
5.2.2 Nominal frequency . 10
5.2.3 Normal test signal . 10
5.2.4 Squelch . 10
5.2.5 Normal audio output power . 10
5.2.6 Audio AGC . 10
5.3 Test channels . 10
5.4 Environmental profile . 11
5.5 Test power source . 11
5.6 Normal test conditions . 11
5.6.1 Normal temperature and humidity . 11
5.6.2 Normal power sources . 11
5.6.2.1 Mains voltage and frequency . 11
5.6.2.2 Other power sources . 11
5.7 Extreme test conditions . 12
5.7.1 Extreme temperatures . 12
5.7.2 Extreme values of test power sources . 12
5.7.2.1 Mains voltage . 12
5.7.2.2 Other power sources . 12
5.8 Performance test . 12
5.9 Environmental tests . 12
5.9.1 General . 12
5.9.2 Procedure for tests at extreme temperatures . 13
5.9.3 Temperature tests . 13
5.9.3.1 General . 13
5.9.3.2 High temperature . 13
5.9.3.3 Low temperature . 13
6 Transmitter . 13
ETSI
4 Draft ETSI EN 302 617 V2.2.0 (2017-05)
6.1 General . 13
6.2 Frequency error . 14
6.2.1 Definition . 14
6.2.2 Method of measurement . 14
6.2.3 Limits . 14
6.3 Carrier power . 14
6.3.1 Definitions . 14
6.3.2 Method of measurement . 14
6.3.3 Tolerances . 14
6.3.3.1 Normal test conditions . 14
6.3.3.2 Extreme test conditions . 14
6.4 Amplitude modulation characteristic. 15
6.4.1 Modulation depth . 15
6.4.1.1 Definitions . 15
6.4.1.2 Method of measurement . 15
6.4.1.3 Limits . 15
6.4.2 Modulation compression . 15
6.4.2.1 Definition . 15
6.4.2.2 Method of measurement . 15
6.4.2.3 Limits . 16
6.4.3 Amplitude modulation distortion . 16
6.4.3.1 Definition . 16
6.4.3.2 Method of measurement . 16
6.4.3.3 Limits . 16
6.4.4 Audio frequency response . 16
6.4.4.1 Definition . 16
6.4.4.2 Method of measurement . 16
6.4.4.3 Limits . 16
6.5 Adjacent channel power . 17
6.5.1 Definition . 17
6.5.2 Measurement. 17
6.5.3 Limits . 17
6.6 Broadband noise . 17
6.6.1 Definition . 17
6.6.2 Method of measurement . 18
6.6.3 Limit . 18
6.7 Conducted spurious emissions (TX). 19
6.7.1 Definition . 19
6.7.2 Method of measurement . 19
6.7.3 Limits . 19
6.8 Intermodulation attenuation. 19
6.8.1 Definition . 19
6.8.2 Method of measurement . 20
6.8.3 Limits . 20
6.9 RF power attack time and release time . 21
6.9.1 Definitions . 21
6.9.2 Method of measurement . 21
6.9.2.1 Attack time . 21
6.9.2.2 Release time . 21
6.9.3 Limits . 22
6.10 Keying Transient frequency behaviour of the transmitter . 22
6.10.1 Definition . 22
6.10.2 Method of measurement . 22
6.10.3 Limits . 23
6.11 Cabinet Radiation (TX) . 23
7 Receiver . 23
7.1 Sensitivity . 23
7.1.1 Definition . 23
7.1.2 Method of measurement . 23
7.1.3 Limits . 23
7.2 Effective acceptance bandwidth . 23
ETSI
5 Draft ETSI EN 302 617 V2.2.0 (2017-05)
7.2.1 Definition . 23
7.2.2 Method of measurement . 24
7.2.3 Limits . 24
7.3 Adjacent channel rejection . 24
7.3.1 Definition . 24
7.3.2 Method of measurement . 24
7.3.3 Limits . 25
7.4 Spurious response rejection . 25
7.4.1 Definition . 25
7.4.2 Introduction to the method of measurement . 25
7.4.3 Method of search of the limited frequency range . 25
7.4.4 Method of measurement . 26
7.4.5 Limit . 26
7.5 Intermodulation response rejection . 26
7.5.1 Definition . 26
7.5.2 Method of measurement . 26
7.5.3 Limit . 27
7.6 Blocking or desensitization . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limit . 28
7.7 Conducted spurious emissions . 28
7.7.1 Definition . 28
7.7.2 Method of measuring the power level . 28
7.7.3 Limits . 28
7.8 Cross modulation rejection . 28
7.8.1 Definition . 28
7.8.2 Method of measurement . 29
7.8.3 Limits . 29
7.9 Receiver dynamic range . 29
7.9.1 Definition . 29
7.9.2 Method of measurement . 29
7.9.3 Limit . 29
7.10 Cabinet Radiation (RX) . 30
8 Testing for compliance with technical requirements . 30
8.1 Environmental conditions for testing . 30
8.2 Interpretation of the measurement results . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Specification for adjacent channel power measurement
arrangements . 34
B.1 Power measuring receiver specification . 34
B.1.1 General . 34
B.1.2 IF filter . 34
B.1.3 Attenuation indicator . 35
B.1.4 RMS value indicator . 35
B.1.5 Oscillator and amplifier . 35
Annex C (informative): Auxiliary cables . 36
Annex D (informative): Change history . 37
History . 38
ETSI
6 Draft ETSI EN 302 617 V2.2.0 (2017-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
7 Draft ETSI EN 302 617 V2.2.0 (2017-05)
1 Scope
The present document specifies technical characteristics and methods of measurements for DSB AM ground based
transmitters, receivers and transceivers operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.1] as well as essential requirements under the Single
European Sky (SES) Interoperability Regulation No 552/2004 [i.3] and related implementing rules and/or essential
requirements under the EASA basic Regulation No 216/2008 [i.5] as amended by Regulation No 1108/2009 [i.6] may
apply to equipment within the scope of the present document.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 113-1 (V1.7.1) (11-2011): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant envelope modulation and having an antenna
connector; Part 1: Technical characteristics and methods of measurement".
[2] Recommendation ITU-T O.41 (10/1994): "Psophometer for use on telephone-type circuits".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] Regulation (EC) 552/2004 of the European Parliament and Council of 10 March 2004 on the
interoperability of the European Air Traffic Management network (the interoperability
Regulation), OJEU L96, 31.03.2004, p. 26-42 as amended by Regulation (EC) 1070/2009 of the
European Parliament and of the Council of 21 October 2009, OJEU L300/34, 14/11/2009.
ETSI
8 Draft ETSI EN 302 617 V2.2.0 (2017-05)
[i.4] ETSI TR 100 028-2 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.5] Regulation (EC) 216/2008 of the European Parliament and of the Council of 20 February 2008 on
common rules in the field of civil aviation and establishing a European Aviation Safety Agency,
and repealing Council Directive 91/670/EEC, Regulation (EC) No 1592/2002 and Directive
2004/36/EC.
[i.6] Regulation (EC) No 1108/2009 of the European Parliament and of the Council of 21 October 2009
amending Regulation (EC) No 216/2008 in the field of aerodromes, air traffic management and air
navigation services and repealing Directive 2006/23/EC.
[i.7] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
aeronautical mobile service: mobile service between aeronautical stations and aircraft stations, or between aircraft
stations, in which survival craft stations may participate
conducted measurements: measurements which are made using a direct RF connection to the equipment under test
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
ground base station: aeronautical station equipment, in the aeronautical mobile service, for use with an external
antenna and intended for use at a fixed location
radiated measurements: measurements which involve the measurement of a radiated field
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
dB decibel
DSB Double Side Band
RF Radio Frequency
RE Radio Equipment
4 General requirements
4.1 Frequency control
25 kHz equipment shall be able to operate on the frequencies 225,000 MHz to 399,975 MHz.
It shall not be possible to transmit while any frequency synthesizer used within the transmitter is out of lock.
It shall not be possible to transmit during channel switching operations.
ETSI
9 Draft ETSI EN 302 617 V2.2.0 (2017-05)
4.2 Controls and indicators
The equipment shall have the following controls and indicators as a minimum:
• a visual indication that the device is switched on;
• a facility to disable the squelch for test purposes (by local or remote control);
• a visual indication that the carrier is being produced.
The equipment shall also meet the following requirements:
• the user shall not have access to any control which, if unintentionally set, might impair the operating
parameters of the equipment.
4.3 Class of emission and modulation characteristics
The equipment shall use Double Side Band (DSB) Amplitude Modulation (AM) full carrier, 6K80A3EJN with 25 kHz
channel spacing.
4.4 Warm up
After being switched on the equipment shall meet the requirements of the present document within one minute under
normal test conditions (see clause 5.6).
If the equipment includes parts which require to be heated in order to operate correctly (e.g. crystal ovens) a
warming-up period of 10 minutes of those parts shall be allowed.
4.5 Protection of the transmitter
4.5.1 Definition
The protection of the transmitter represents the ability of the transmitter to be protected against malfunction due to
faults in the antenna system. This shall be the first test applied to a transmitter.
4.5.2 Method of measurement
While the transmitter is transmitting at the rated output power, the antenna port shall first be short-circuited and then
open-circuited, in each case for a period of 1 minute. This test shall be performed on 312,5 MHz only.
4.5.3 Requirement
This test shall not result in any damage to the transmitter. After removal of the short-circuit and open-circuit conditions,
the transmitter shall be able to operate normally when re-keyed.
5 General conditions of measurement
5.1 Transmitter test signal arrangement
5.1.1 Coaxial termination
When tests are carried out with a coaxial termination, this shall be a non-reactive, non radiating 50 Ω load.
ETSI
10 Draft ETSI EN 302 617 V2.2.0 (2017-05)
5.1.2 Signal sources
The modulating signals shall be applied to the transmitter through the modulating audio input.
5.1.3 Normal test signal
The normal test signal shall be a 1 kHz sinewave at a level which produces a 30 % amplitude modulation depth, of the
transmitter RF output, unless otherwise defined.
5.2 Receiver test signal arrangement
5.2.1 Test signal sources
Test signal sources shall be connected to the receiver input in such a way that the impedance presented to the receiver
input is 50 Ω, irrespective of whether one or more test signals are applied to the receiver simultaneously.
5.2.2 Nominal frequency
The nominal frequency of the receiver is the carrier frequency of the selected channel.
5.2.3 Normal test signal
The normal test signal shall be a Double Side Band (DSB) signal with carrier, amplitude modulated with
1 kHz sinewave to a depth of 30 %.
5.2.4 Squelch
Unless otherwise stated the receiver squelch facility shall be made inoperative for the duration of the tests.
5.2.5 Normal audio output power
The rated audio frequency output power is the value stated by the manufacturer to be the maximum power available at
the output, for which all the requirements of the present document are met.
The audio frequency output power shall be maintained at 50 % of the rated output in the presence of a desired signal
unless otherwise defined.
5.2.6 Audio AGC
When an audio AGC function is provided, this shall be disabled (where possible) unless otherwise stated.
5.3 Test channels
Tests shall be carried out on three frequencies unless otherwise stated:
• 225,000 MHz;
• 312,500 MHz;
• 399,975 MHz.
ETSI
11 Draft ETSI EN 302 617 V2.2.0 (2017-05)
5.4 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer, but as a minimum, shall be that specified in the test conditions
contained in the present document. The equipment shall comply with all the technical requirements of the present
document which are identified as applicable in annex A at all times when operating within the boundary limits of the
declared operational environmental profile.
Measurements shall be made under normal test conditions (see clause 5.6) and also, where stated, under extreme test
conditions (see clauses 5.7).
5.5 Test power source
During testing, the equipment shall be supplied from a test power source capable of producing normal and extreme test
voltages.
The internal impedance of the test power source shall be low enough for its effect on the test results to be negligible.
For the purpose of testing the power source voltage shall be measured at the input terminals of the equipment.
During testing, the power source voltages shall be maintained within a tolerance of ±3 % relative to the voltage level at
the beginning of each test.
5.6 Normal test conditions
5.6.1 Normal temperature and humidity
The normal temperature and humidity conditions for tests shall be a combination of temperature and humidity within
the following ranges:
• temperature: +15 °C to +35 °C;
• relative humidity: 20 % to 75 %.
When it is impracticable to carry out the tests under these conditions, a note to this effect, stating the ambient
temperature and relative humidity during the tests, shall be added to the test report.
5.6.2 Normal power sources
5.6.2.1 Mains voltage and frequency
The normal test voltage for equipment to be connected to the mains shall be the nominal mains voltage.
For the purpose of the present document, the nominal voltage shall be the declared voltage or any of the declared
voltages for which the equipment was designed.
The frequency of the test power source corresponding to the AC mains shall be between 49 Hz and 51 Hz.
5.6.2.2 Other power sources
For operation from other power sources or types of battery (primary or secondary), the normal test voltage shall be that
declared by the equipment manufacturer.
ETSI
12 Draft ETSI EN 302 617 V2.2.0 (2017-05)
5.7 Extreme test conditions
5.7.1 Extreme temperatures
For tests at extreme temperatures, measurements shall be made in accordance with clause 5.8, at a lower temperature of
-20 °C and an upper temperature of +55 °C. This test shall be performed at the nominal supply voltage as defined in
clause 5.6.2.
5.7.2 Extreme values of test power sources
5.7.2.1 Mains voltage
The extreme test voltages shall be between 207 V and 253 V. This test shall be p
...
HARMONISED EUROPEAN STANDARD
Ground-based UHF radio transmitters,
receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
2 ETSI EN 302 617 V2.2.1 (2017-11)
Reference
REN/ERM-TGAERO-50
Keywords
aeronautical, AM, DSB, harmonised standard,
radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 617 V2.2.1 (2017-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 8
4 General requirements . 8
4.1 Frequency control . 8
4.2 Controls and indicators . 9
4.3 Class of emission and modulation characteristics . 9
4.4 Warm up . 9
4.5 Protection of the transmitter . 9
4.5.1 Definition . 9
4.5.2 Method of measurement . 9
4.5.3 Requirement . 9
5 General conditions of measurement . 9
5.1 Transmitter test signal arrangement . 9
5.1.1 Coaxial termination. 9
5.1.2 Signal sources . 10
5.1.3 Normal test signal . 10
5.2 Receiver test signal arrangement . 10
5.2.1 Test signal sources . 10
5.2.2 Nominal frequency . 10
5.2.3 Normal test signal . 10
5.2.4 Squelch . 10
5.2.5 Normal audio output power . 10
5.2.6 Audio AGC . 10
5.3 Test channels . 10
5.4 Environmental profile . 11
5.5 Test power source . 11
5.6 Normal test conditions . 11
5.6.1 Normal temperature and humidity . 11
5.6.2 Normal power sources . 11
5.6.2.1 Mains voltage and frequency . 11
5.6.2.2 Other power sources . 11
5.7 Extreme test conditions . 12
5.7.1 Extreme temperatures . 12
5.7.2 Extreme values of test power sources . 12
5.7.2.1 Mains voltage . 12
5.7.2.2 Other power sources . 12
5.8 Performance test . 12
5.9 Environmental tests . 12
5.9.1 General . 12
5.9.2 Procedure for tests at extreme temperatures . 13
5.9.3 Temperature tests . 13
5.9.3.1 General . 13
5.9.3.2 High temperature . 13
5.9.3.3 Low temperature . 13
6 Transmitter . 13
ETSI
4 ETSI EN 302 617 V2.2.1 (2017-11)
6.1 General . 13
6.2 Frequency error . 14
6.2.1 Definition . 14
6.2.2 Method of measurement . 14
6.2.3 Limits . 14
6.3 Carrier power . 14
6.3.1 Definitions . 14
6.3.2 Method of measurement . 14
6.3.3 Tolerances . 14
6.3.3.1 Normal test conditions . 14
6.3.3.2 Extreme test conditions . 14
6.4 Amplitude modulation characteristic. 15
6.4.1 Modulation depth . 15
6.4.1.1 Definitions . 15
6.4.1.2 Method of measurement . 15
6.4.1.3 Limits . 15
6.4.2 Modulation compression . 15
6.4.2.1 Definition . 15
6.4.2.2 Method of measurement . 15
6.4.2.3 Limits . 16
6.4.3 Amplitude modulation distortion . 16
6.4.3.1 Definition . 16
6.4.3.2 Method of measurement . 16
6.4.3.3 Limits . 16
6.4.4 Audio frequency response . 16
6.4.4.1 Definition . 16
6.4.4.2 Method of measurement . 16
6.4.4.3 Limits . 16
6.5 Adjacent channel power . 17
6.5.1 Definition . 17
6.5.2 Measurement. 17
6.5.3 Limits . 17
6.6 Broadband noise . 17
6.6.1 Definition . 17
6.6.2 Method of measurement . 18
6.6.3 Limit . 18
6.7 Conducted spurious emissions (TX). 19
6.7.1 Definition . 19
6.7.2 Method of measurement . 19
6.7.3 Limits . 19
6.8 Intermodulation attenuation. 19
6.8.1 Definition . 19
6.8.2 Method of measurement . 20
6.8.3 Limits . 20
6.9 RF power attack time and release time . 21
6.9.1 Definitions . 21
6.9.2 Method of measurement . 21
6.9.2.1 Attack time . 21
6.9.2.2 Release time . 21
6.9.3 Limits . 22
6.10 Keying Transient frequency behaviour of the transmitter . 22
6.10.1 Definition . 22
6.10.2 Method of measurement . 22
6.10.3 Limits . 23
6.11 Cabinet Radiation (TX) . 23
7 Receiver . 23
7.1 Sensitivity . 23
7.1.1 Definition . 23
7.1.2 Method of measurement . 23
7.1.3 Limits . 23
7.2 Effective acceptance bandwidth . 23
ETSI
5 ETSI EN 302 617 V2.2.1 (2017-11)
7.2.1 Definition . 23
7.2.2 Method of measurement . 24
7.2.3 Limits . 24
7.3 Adjacent channel rejection . 24
7.3.1 Definition . 24
7.3.2 Method of measurement . 24
7.3.3 Limits . 25
7.4 Spurious response rejection . 25
7.4.1 Definition . 25
7.4.2 Introduction to the method of measurement . 25
7.4.3 Method of search of the limited frequency range . 25
7.4.4 Method of measurement . 26
7.4.5 Limit . 26
7.5 Intermodulation response rejection . 26
7.5.1 Definition . 26
7.5.2 Method of measurement . 26
7.5.3 Limit . 27
7.6 Blocking or desensitization . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limit . 28
7.7 Conducted spurious emissions . 28
7.7.1 Definition . 28
7.7.2 Method of measuring the power level . 28
7.7.3 Limits . 28
7.8 Cross modulation rejection . 28
7.8.1 Definition . 28
7.8.2 Method of measurement . 29
7.8.3 Limits . 29
7.9 Receiver dynamic range . 29
7.9.1 Definition . 29
7.9.2 Method of measurement . 29
7.9.3 Limit . 29
7.10 Cabinet Radiation (RX) . 30
8 Testing for compliance with technical requirements . 30
8.1 Environmental conditions for testing . 30
8.2 Interpretation of the measurement results . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Specification for adjacent channel power measurement
arrangements . 34
B.1 Power measuring receiver specification . 34
B.1.1 General . 34
B.1.2 IF filter . 34
B.1.3 Attenuation indicator . 35
B.1.4 RMS value indicator . 35
B.1.5 Oscillator and amplifier . 35
Annex C (informative): Auxiliary cables . 36
Annex D (informative): Change history . 37
History . 38
ETSI
6 ETSI EN 302 617 V2.2.1 (2017-11)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 21 August 2017
Date of latest announcement of this EN (doa): 30 November 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2018
Date of withdrawal of any conflicting National Standard (dow): 31 May 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
7 ETSI EN 302 617 V2.2.1 (2017-11)
1 Scope
The present document specifies technical characteristics and methods of measurements for DSB AM ground based
transmitters, receivers and transceivers operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.1] as well as essential requirements under the Single
European Sky (SES) Interoperability Regulation No 552/2004 [i.3] and related implementing rules and/or essential
requirements under the EASA basic Regulation No 216/2008 [i.5] as amended by Regulation No 1108/2009 [i.6] may
apply to equipment within the scope of the present document.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 113-1 (V1.7.1) (11-2011): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data
(and/or speech) using constant or non-constant envelope modulation and having an antenna
connector; Part 1: Technical characteristics and methods of measurement".
[2] Recommendation ITU-T O.41 (10/1994): "Psophometer for use on telephone-type circuits".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.3] Regulation (EC) 552/2004 of the European Parliament and Council of 10 March 2004 on the
interoperability of the European Air Traffic Management network (the interoperability
Regulation), OJEU L96, 31.03.2004, p. 26-42 as amended by Regulation (EC) 1070/2009 of the
European Parliament and of the Council of 21 October 2009, OJEU L300/34, 14/11/2009.
ETSI
8 ETSI EN 302 617 V2.2.1 (2017-11)
[i.4] ETSI TR 100 028-2 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.5] Regulation (EC) 216/2008 of the European Parliament and of the Council of 20 February 2008 on
common rules in the field of civil aviation and establishing a European Aviation Safety Agency,
and repealing Council Directive 91/670/EEC, Regulation (EC) No 1592/2002 and Directive
2004/36/EC.
[i.6] Regulation (EC) No 1108/2009 of the European Parliament and of the Council of 21 October 2009
amending Regulation (EC) No 216/2008 in the field of aerodromes, air traffic management and air
navigation services and repealing Directive 2006/23/EC.
[i.7] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
aeronautical mobile service: mobile service between aeronautical stations and aircraft stations, or between aircraft
stations, in which survival craft stations may participate
conducted measurements: measurements which are made using a direct RF connection to the equipment under test
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
ground base station: aeronautical station equipment, in the aeronautical mobile service, for use with an external
antenna and intended for use at a fixed location
radiated measurements: measurements which involve the measurement of a radiated field
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AM Amplitude Modulation
dB decibel
DSB Double Side Band
RE Radio Equipment
RF Radio Frequency
4 General requirements
4.1 Frequency control
25 kHz equipment shall be able to operate on the frequencies 225,000 MHz to 399,975 MHz.
It shall not be possible to transmit while any frequency synthesizer used within the transmitter is out of lock.
It shall not be possible to transmit during channel switching operations.
ETSI
9 ETSI EN 302 617 V2.2.1 (2017-11)
4.2 Controls and indicators
The equipment shall have the following controls and indicators as a minimum:
• a visual indication that the device is switched on;
• a facility to disable the squelch for test purposes (by local or remote control);
• a visual indication that the carrier is being produced.
The equipment shall also meet the following requirements:
• the user shall not have access to any control which, if unintentionally set, might impair the operating
parameters of the equipment.
4.3 Class of emission and modulation characteristics
The equipment shall use Double Side Band (DSB) Amplitude Modulation (AM) full carrier, 6K80A3EJN with 25 kHz
channel spacing.
4.4 Warm up
After being switched on the equipment shall meet the requirements of the present document within one minute under
normal test conditions (see clause 5.6).
If the equipment includes parts which require to be heated in order to operate correctly (e.g. crystal ovens) a
warming-up period of 10 minutes of those parts shall be allowed.
4.5 Protection of the transmitter
4.5.1 Definition
The protection of the transmitter represents the ability of the transmitter to be protected against malfunction due to
faults in the antenna system. This shall be the first test applied to a transmitter.
4.5.2 Method of measurement
While the transmitter is transmitting at the rated output power, the antenna port shall first be short-circuited and then
open-circuited, in each case for a period of 1 minute. This test shall be performed on 312,5 MHz only.
4.5.3 Requirement
This test shall not result in any damage to the transmitter. After removal of the short-circuit and open-circuit conditions,
the transmitter shall be able to operate normally when re-keyed.
5 General conditions of measurement
5.1 Transmitter test signal arrangement
5.1.1 Coaxial termination
When tests are carried out with a coaxial termination, this shall be a non-reactive, non radiating 50 Ω load.
ETSI
10 ETSI EN 302 617 V2.2.1 (2017-11)
5.1.2 Signal sources
The modulating signals shall be applied to the transmitter through the modulating audio input.
5.1.3 Normal test signal
The normal test signal shall be a 1 kHz sinewave at a level which produces a 30 % amplitude modulation depth, of the
transmitter RF output, unless otherwise defined.
5.2 Receiver test signal arrangement
5.2.1 Test signal sources
Test signal sources shall be connected to the receiver input in such a way that the impedance presented to the receiver
input is 50 Ω, irrespective of whether one or more test signals are applied to the receiver simultaneously.
5.2.2 Nominal frequency
The nominal frequency of the receiver is the carrier frequency of the selected channel.
5.2.3 Normal test signal
The normal test signal shall be a Double Side Band (DSB) signal with carrier, amplitude modulated with 1 kHz
sinewave to a depth of 30 %.
5.2.4 Squelch
Unless otherwise stated the receiver squelch facility shall be made inoperative for the duration of the tests.
5.2.5 Normal audio output power
The rated audio frequency output power is the value stated by the manufacturer to be the maximum power available at
the output, for which all the requirements of the present document are met.
The audio frequency output power shall be maintained at 50 % of the rated output in the presence of a desired signal
unless otherwise defined.
5.2.6 Audio AGC
When an audio AGC function is provided, this shall be disabled (where possible) unless otherwise stated.
5.3 Test channels
Tests shall be carried out on three frequencies unless otherwise stated:
• 225,000 MHz;
• 312,500 MHz;
• 399,975 MHz.
ETSI
11 ETSI EN 302 617 V2.2.1 (2017-11)
5.4 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer, but as a minimum, shall be that specified in the test conditions
contained in the present document. The equipment shall comply with all the technical requirements of the present
document which are identified as applicable in annex A at all times when operating within the boundary limits of the
declared operational environmental profile.
Measurements shall be made under normal test conditions (see clause 5.6) and also, where stated, under extreme test
conditions (see clauses 5.7).
5.5 Test power source
During testing, the equipment shall be supplied from a test power source capable of producing normal and extreme test
voltages.
The internal impedance of the test power source shall be low enough for its effect on the test results to be negligible.
For the purpose of testing the power source voltage shall be measured at the input terminals of the equipment.
During testing, the power source voltages shall be maintained within a tolerance of ±3 % relative to the voltage level at
the beginning of each test.
5.6 Normal test conditions
5.6.1 Normal temperature and humidity
The normal temperature and humidity conditions for tests shall be a combination of temperature and humidity within
the following ranges:
• temperature: +15 °C to +35 °C;
• relative humidity: 20 % to 75 %.
When it is impracticable to carry out the tests under these conditions, a note to this effect, stating the ambient
temperature and relative humidity during the tests, shall be added to the test report.
5.6.2 Normal power sources
5.6.2.1 Mains voltage and frequency
The normal test voltage for equipment to be connected to the mains shall be the nominal mains voltage.
For the purpose of the present document, the nominal voltage shall be the declared voltage or any of the declared
voltages for which the equipment was designed.
The frequency of the test power source corresponding to the AC mains shall be between 49 Hz and 51 Hz.
5.6.2.2 Other power sources
For operation from other power sources or types of battery (primary or secondary), the normal test voltage shall be that
declared by the equipment manufacturer.
ETSI
12 ETSI EN 302 617 V2.2.1 (2017-11)
5.7 Extreme test conditions
5.7.1 Extreme temperatures
For tests at extreme temperatures, measurements shall be made in accordance with clause 5.8, at a lower temperature of
-20 °C and an upper te
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.(8Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU49.090On-board equipment and instruments33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 302 617 V2.2.1 (2017-11)SIST EN 302 617 V2.2.1:2018en01-januar-2018SIST EN 302 617 V2.2.1:2018SLOVENSKI
STANDARD
=====ETSI EN 302 617 V2.2.1 (2017-11) Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 2 =====oeference=REN/ERM-TGAERO-50 heywords=aeronautical, AM, DSB, harmonised standard, radio, testing, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE= Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 3 Contents fntellectual=mroperty=oights=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=p coreword=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=p jodal=verbs=terminology=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=p k=pcope=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=q l=oeferences=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=q lhk=kormative=references=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=q lhl=fnformative=references=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=q m=aefinitions=and=abbreviations=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=r mhk=aefinitions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=r mhl=Abbreviations=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=r 4=deneral=requirements=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=r 4hk=crequency=control=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=r 4hl=Controls=and=indicators=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4hm=Class=of=emission=and=modulation=characteristics=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4h4=tarm=up=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4ho=mrotection=of=the=transmitter=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4hohk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4hohl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s 4hohm=oequirement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s o=deneral=conditions=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s ohk=qransmitter=test=signal=arrangement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s ohkhk=Coaxial=terminationhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=s ohkhl=pignal=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohkhm=kormal=test=signal=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohl=oeceiver=test=signal=arrangement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlhk=qest=signal=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlhl=kominal=frequency=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlhm=kormal=test=signal=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlh4=pquelch=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlho=kormal=audio=output=power=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohlhp=Audio=AdC=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj ohm=qest=channels=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kj oh4=bnvironmental=profile=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk oho=qest=power=source=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohp=kormal=test=conditions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohphk=kormal=temperature=and=humidity=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohphl=kormal=power=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohphlhk=jains=voltage=and=frequency=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohphlhl=lther=power=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kk ohq=bxtreme=test=conditions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohqhk=bxtreme=temperatures=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohqhl=bxtreme=values=of=test=power=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohqhlhk=jains=voltage=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohqhlhl=lther=power=sources=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohr=merformance=test=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohs=bnvironmental=tests=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohshk=deneral=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kl ohshl=mrocedure=for=tests=at=extreme=temperatures=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km ohshm=qemperature=tests=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km ohshmhk=deneral=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km ohshmhl=eigh=temperature=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km ohshmhm=iow=temperature=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km p=qransmitter=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 4 phk=deneral=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=km phl=crequency=error=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phlhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phlhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phlhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phm=Carrier=power=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phmhk=aefinitions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phmhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phmhm=qolerances=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phmhmhk=kormal=test=conditions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 phmhmhl=bxtreme=test=conditions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=k4 ph4=Amplitude=modulation=characteristichhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hk=jodulation=depth=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hkhk=aefinitions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hkhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hkhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hl=jodulation=compression=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hlhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hlhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ko ph4hlhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4hm=Amplitude=modulation=distortion=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4hmhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4hmhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4hmhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4h4=Audio=frequency=response=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4h4hk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4h4hl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp ph4h4hm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kp pho=Adjacent=channel=power=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq phohk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq phohl=jeasurementhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq phohm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq php=Broadband=noise=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq phphk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kq phphl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kr phphm=iimit=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=kr phq=Conducted=spurious=emissions=bquchhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phqhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phqhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phqhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phr=fntermodulation=attenuationhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phrhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ks phrhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lj phrhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lj phs=oc=power=attack=time=and=release=time=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lk phshk=aefinitions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lk phshl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lk phshlhk=Attack=time=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lk phshlhl=oelease=time=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lk phshm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ll phkj=heying=qransient=frequency=behaviour=of=the=transmitter=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ll phkjhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ll phkjhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ll phkjhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm phkk=Cabinet=oadiation=bquc=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm q=oeceiver=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhk=pensitivity=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhkhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhkhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhkhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhl=bffective=acceptance=bandwidth=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 5 qhlhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lm qhlhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=l4 qhlhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=l4 qhm=Adjacent=channel=rejection=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=l4 qhmhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=l4 qhmhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=l4 qhmhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lo qh4=ppurious=response=rejection=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lo qh4hk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lo qh4hl=fntroduction=to=the=method=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lo qh4hm=jethod=of=search=of=the=limited=frequency=range=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lo qh4h4=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lp qh4ho=iimit=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lp qho=fntermodulation=response=rejection=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lp qhohk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lp qhohl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lp qhohm=iimit=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lq qhp=Blocking=or=desensitization=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lq qhphk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lq qhphl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lq qhphm=iimit=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhq=Conducted=spurious=emissions=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhqhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhqhl=jethod=of=measuring=the=power=level=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhqhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhr=Cross=modulation=rejection=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhrhk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=lr qhrhl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhrhm=iimits=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhs=oeceiver=dynamic=range=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhshk=aefinition=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhshl=jethod=of=measurement=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhshm=iimit=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=ls qhkj=Cabinet=oadiation=bouc=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mj r=qesting=for=compliance=with=technical=requirements=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mj rhk=bnvironmental=conditions=for=testing=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mj rhl=fnterpretation=of=the=measurement=results=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mj Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 32 Annex B (normative): Specification for adjacent channel power measurement arrangements . 34 Bhk=mower=measuring=receiver=specification=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=m4 Bhkhk=deneral=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=m4 Bhkhl=fc=filter=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=m4 Bhkhm=Attenuation=indicator=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mo Bhkh4=ojp=value=indicator=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mo Bhkho=lscillator=and=amplifier=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mo Annex C (informative): Auxiliary cables . 36 Annex D (informative): Change history . 37 eistory=hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh=mr =SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 6 Intellectual Property Rights Essential patents fmos=essential=or=potentially=essential=to=the=present=document=may=have=been=declared=to=bqpfh=qhe=information=pertaining=to=these=essential=fmosf=if=anyf=is=publicly=available=for=ETSI members and non-membersf=and=can=be=found=in=bqpf=po=jjj=mk4t="Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards"f=which=is=available=from=the=bqpf=pecretariath=iatest=updates=are=available=on=the=bqpf=teb=server=bhttpstiiiprhetsihorgich=mursuant=to=the=bqpf=fmo=molicyf=no=investigationf=including=fmo=searchesf=has=been=carried=out=by=bqpfh=ko=guarantee=can=be=given=as=to=the=existence=of=other=fmos=not=referenced=in=bqpf=po=jjj=mk4=bor=the=updates=on=the=bqpf=teb=serverc=which=aref=or=may=bef=or=may=becomef=essential=to=the=present=documenth=Trademarks qhe=present=document=may=include=trademarks=andior=tradenames=which=are=asserted=andior=registered=by=their=ownersh=bqpf=claims=no=ownership=of=these=except=for=any=which=are=indicated=as=being=the=property=of=bqpff=and=conveys=no=right=to=use=or=reproduce=any=trademark=andior=tradenameh=jention=of=those=trademarks=in=the=present=document=does=not=constitute=an=endorsement=by=bqpf=of=productsf=services=or=organizations=associated=with=those=trademarksh=Foreword qhis=earmonised=buropean=ptandard=bbkc=has=been=produced=by=bqpf=qechnical=Committee=blectromagnetic=compatibility=and=oadio=spectrum=jatters=bbojch=qhe=present=document=has=been=prepared=under=the=Commissionas=standardisation=request=Cbljkoc=omqp=final=xihqz=to=provide=one=voluntary=means=of=conforming=to=the=essential=requirements=of=airective=ljk4iomibr=on=the=harmonisation=of=the=laws=of=the=jember=ptates=relating=to=the=making=available=on=the=market=of=radio=equipment=and=repealing=airective=ksssioibC=xihkzh=lnce=the=present=document=is=cited=in=the=lfficial=gournal=of=the=buropean=rnion=under=that=airectivef=compliance=with=the=normative=clauses=of=the=present=document=given=in=table=Ahk=confersf=within=the=limits=of=the=scope=of=the=present=documentf=a=presumption=of=conformity=with=the=corresponding=essential=requirements=of=that=airective=and=associated=bcqA=regulationsh==National transposition dates aate=of=adoption=of=this=bkt=lk=August=ljkq=aate=of=latest=announcement=of=this=bk=bdoact=mj=kovember=ljkq=aate=of=latest=publication=of=new=kational=ptandard=or=endorsement=of=this=bk=bdopiect==mk=jay=ljkr=aate=of=withdrawal=of=any=conflicting=kational=ptandard=bdowct=mk=jay=ljkr==Modal verbs terminology fn=the=present=document="shall"f="shall not"f="should"f="should not"f="may"f="need not"f="will"f="will not"f="can"=and="cannot"=are=to=be=interpreted=as=described=in=clause=mhl=of=the=bqpf=arafting=oules=bserbal=forms=for=the=expression=of=provisionsch="must"=and="must not"=are=NOT=allowed=in=bqpf=deliverables=except=when=used=in=direct=citationh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 7 1 Scope qhe=present=document=specifies=technical=characteristics=and=methods=of=measurements=for=apB=Aj=ground=based=transmittersf=receivers=and=transceivers=operating=in=all=or=any=part=of=the=aeronautical=frequency=band=between=llo=jez=and=mssfsqo=jezh=qhe=present=document=covers=the=essential=requirements=of=article=mhl=of=airective=ljk4iomibr=xihkz=under=the=conditions=identified=in=annex=Ah=fn=addition=to=the=present=documentf=other=bks=that=specify=technical=requirements=in=respect=of=essential=requirements=under=other=parts=of=article=m=of=the=airective=ljk4iomibr=xihkz=as=well=as=essential=requirements=under=the=pingle=buropean=pky=bpbpc=fnteroperability=oegulation=ko=ooliljj4=xihmz=and=related=implementing=rules=andior=essential=requirements=under=the=bApA=basic=oegulation=ko=lkpiljjr=xihoz=as=amended=by=oegulation=ko=kkjriljjs=xihpz=may=apply=to=equipment=within=the=scope=of=the=present=documenth=2 References 2.1 Normative references oeferences=are=specificf=identified=by=date=of=publication=andior=edition=number=or=version=numberh=lnly=the=cited=version=appliesh=oeferenced=documents=which=are=not=found=to=be=publicly=available=in=the=expected=location=might=be=found=at=httpstiidocboxhetsihorgioeferenceih=klqbt=thile=any=hyperlinks=included=in=this=clause=were=valid=at=the=time=of=publicationf=bqpf=cannot=guarantee=their=long=term=validityh=qhe=following=referenced=documents=are=necessary=for=the=application=of=the=present=documenth=xkz=bqpf=bk=mjj=kkmgk=bskhqhkc=bkkgljkkct="blectromagnetic=compatibility=and=oadio=spectrum=jatters=bbojcu=iand=mobile=serviceu=oadio=equipment=intended=for=the=transmission=of=data=bandior=speechc=using=constant=or=nongconstant=envelope=modulation=and=having=an=antenna=connectoru=mart=kt=qechnical=characteristics=and=methods=of=measurement"h=xlz=oecommendation=fqrgq=lh4k=bkjikss4ct="msophometer=for=use=on=telephonegtype=circuits"h=2.2 Informative references oeferences=are=either=specific=bidentified=by=date=of=publication=andior=edition=number=or=version=numberc=or=nongspecifich=cor=specific=referencesf=only=the=cited=version=appliesh=cor=nongspecific=referencesf=the=latest=version=of=the=referenced=document=bincluding=any=amendmentsc=appliesh=klqbt=thile=any=hyperlinks=included=in=this=clause=were=valid=at=the=time=of=publicationf=bqpf=cannot=guarantee=their=long=term=validityh=qhe=following=referenced=documents=are=not=necessary=for=the=application=of=the=present=document=but=they=assist=the=user=with=regard=to=a=particular=subject=areah=xihkz=airective=ljk4iomibr=of=the=buropean=marliament=and=of=the=Council=of=kp=April=ljk4=on=the=harmonisation=of=the=laws=of=the=jember=ptates=relating=to=the=making=available=on=the=market=of=radio=equipment=and=repealing=airective=ksssioibCh=xihlz=bqpf=qo=kjj=jlr=ball=partsc=bskh4hkct="blectromagnetic=compatibility=and=oadio=spectrum=jatters=bbojcu=rncertainties=in=the=measurement=of=mobile=radio=equipment=characteristics"h=xihmz=oegulation=bbCc=ooliljj4=of=the=buropean=marliament=and=Council=of=kj=jarch=ljj4=on=the=interoperability=of=the=buropean=Air=qraffic=janagement=network=bthe=interoperability=oegulationcf=lgbr=ispf=mkhjmhljj4f=ph=lpg4l=as=amended=by=oegulation=bbCc=kjqjiljjs=of=the=buropean=marliament=and=of=the=Council=of=lk=lctober=ljjsf=lgbr=imjjim4f=k4ikkiljjsh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 8 xih4z=bqpf=qo=kjj=jlrgl=bskh4hkct="blectromagnetic=compatibility=and=oadio=spectrum=jatters=bbojcu=rncertainties=in=the=measurement=of=mobile=radio=equipment=characteristicsu=mart=l"h=xihoz=oegulation=bbCc=lkpiljjr=of=the=buropean=marliament=and=of=the=Council=of=lj=cebruary=ljjr=on=common=rules=in=the=field=of=civil=aviation=and=establishing=a=buropean=Aviation=pafety=Agencyf=and=repealing=Council=airective=skipqjibbCf=oegulation=bbCc=ko=kosliljjl=and=airective=ljj4impibCh=xihpz=oegulation=bbCc=ko=kkjriljjs=of=the=buropean=marliament=and=of=the=Council=of=lk=lctober=ljjs=amending=oegulation=bbCc=ko=lkpiljjr=in=the=field=of=aerodromesf=air=traffic=management=and=air=navigation=services=and=repealing=airective=ljjpilmibCh=xihqz=Commission=fmplementing=aecision=Cbljkoc=omqp=final=of=4hrhljko=on=a=standardisation=request=to=the=buropean=Committee=for=blectrotechnical=ptandardisation=and=to=the=buropean=qelecommunications=ptandards=fnstitute=as=regards=radio=equipment=in=support=of=airective=ljk4iomibr=of=the=buropean=marliament=and=of=the=Councilh=3 Definitions and abbreviations 3.1 Definitions cor=the=purposes=of=the=present=documentf=the=following=terms=and=definitions=applyt=aeronautical mobile service:=mobile=service=between=aeronautical=stations=and=aircraft=stationsf=or=between=aircraft=stationsf=in=which=survival=craft=stations=may=participate=conducted measurements:=measurements=which=are=made=using=a=direct=oc=connection=to=the=equipment=under=test=environmental profile: range of=environmental=conditions=under=which=equipment=within=the=scope=of=the=present=document=is=required=to=comply=with=the=provisions=of=the=present=document=ground base station:=aeronautical=station=equipmentf=in=the=aeronautical=mobile=servicef=for=use=with=an=external=antenna=and=intended=for=use=at=a=fixed=location=radiated measurements:=measurements=which=involve=the=measurement=of=a=radiated=field=3.2 Abbreviations cor=the=purposes=of=the=present=documentf=the=following=abbreviations=applyt=Aj=Amplitude=jodulation=dB=decibel=apB=aouble=pide=Band=ob=oadio=bquipment=oc=oadio=crequency=4 General requirements 4.1 Frequency control lo=kez=equipment=shall=be=able=to=operate=on=the=frequencies=llofjjj=jez=to=mssfsqo=jezh=ft=shall=not=be=possible=to=transmit=while=any=frequency=synthesizer=used=within=the=transmitter=is=out=of=lockh=ft=shall=not=be=possible=to=transmit=during=channel=switching=operationsh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 9 4.2 Controls and indicators qhe=equipment=shall=have=the=following=controls=and=indicators=as=a=minimumt=• a=visual=indication=that=the=device=is=switched=onu=• a=facility=to=disable=the=squelch=for=test=purposes=bby=local=or=remote=controlcu=• a=visual=indication=that=the=carrier=is=being=producedh=qhe=equipment=shall=also=meet=the=following=requirementst=• the=user=shall=not=have=access=to=any=control=whichf=if=unintentionally=setf=might=impair=the=operating=parameters=of=the=equipmenth 4.3 Class of emission and modulation characteristics qhe=equipment=shall=use=aouble=pide=Band=bapBc=Amplitude=jodulation=bAjc=full=carrierf=phrjAmbgk=with=lo=kez=channel=spacingh=4.4 Warm up After=being=switched=on=the=equipment=shall=meet=the=requirements=of=the=present=document=within=one=minute=under=normal=test=conditions=bsee=clause=ohpch=ff=the=equipment=includes=parts=which=require=to=be=heated=in=order=to=operate=correctly=behgh=crystal=ovensc=a=warminggup=period=of=kj=minutes=of=those=parts=shall=be=allowedh=4.5 Protection of the transmitter 4.5.1 Definition qhe=protection=of=the=transmitter=represents=the=ability=of=the=transmitter=to=be=protected=against=malfunction=due=to=faults=in=the=antenna=systemh=qhis=shall=be=the=first=test=applied=to=a=transmitterh=4.5.2 Method of measurement thile=the=transmitter=is=transmitting=at=the=rated=output=powerf=the=antenna=port=shall=first=be=shortgcircuited=and=then=opengcircuitedf=in=each=case=for=a=period=of=k=minuteh=qhis=test=shall=be=performed=on=mklfo=jez=onlyh=4.5.3 Requirement qhis=test=shall=not=result=in=any=damage=to=the=transmitterh=After=removal=of=the=shortgcircuit=and=opengcircuit=conditionsf=the=transmitter=shall=be=able=to=operate=normally=when=regkeyedh=5 General conditions of measurement 5.1 Transmitter test signal arrangement 5.1.1 Coaxial termination then=tests=are=carried=out=with=a=coaxial=terminationf=this=shall=be=a=nongreactivef=non=radiating=oj=Ω=loadh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 10 5.1.2 Signal sources qhe=modulating=signals=shall=be=applied=to=the=transmitter=through=the=modulating=audio=inputh=5.1.3 Normal test signal qhe=normal=test=signal=shall=be=a=k=kez=sinewave=at=a=level=which=produces=a=mj=B=amplitude=modulation=depthf=of=the=transmitter=oc=outputf=unless=otherwise=definedh=5.2 Receiver test signal arrangement 5.2.1 Test signal sources qest=signal=sources=shall=be=connected=to=the=receiver=input=in=such=a=way=that=the=impedance=presented=to=the=receiver=input=is=oj=Ωf=irrespective=of=whether=one=or=more=test=signals=are=applied=to=the=receiver=simultaneouslyh=5.2.2 Nominal frequency qhe=nominal=frequency=of=the=receiver=is=the=carrier=frequency=of=the=selected=channelh=5.2.3 Normal test signal qhe=normal=test=signal=shall=be=a=aouble=pide=Band=bapBc=signal=with=carrierf=amplitude=modulated=with=k=kez=sinewave=to=a=depth=of=mj=Bh=5.2.4 Squelch rnless=otherwise=stated=the=receiver=squelch=facility=shall=be=made=inoperative=for=the=duration=of=the=testsh=5.2.5 Normal audio output power qhe=rated=audio=frequency=output=power=is=the=value=stated=by=the=manufacturer=to=be=the=maximum=power=available=at=the=outputf=for=which=all=the=requirements=of=the=present=document=are=meth=qhe=audio=frequency=output=power=shall=be=maintained=at=oj=B=of=the=rated=output=in=the=presence=of=a=desired=signal=unless=otherwise=definedh=5.2.6 Audio AGC then=an=audio=AdC=function=is=providedf=this=shall=be=disabled=bwhere=possiblec=unless=otherwise=statedh=5.3 Test channels qests=shall=be=carried=out=on=three=frequencies=unless=otherwise=statedt=• llofjjj=jezu=• mklfojj=jezu=• mssfsqo=jezh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 11 5.4 Environmental profile qhe=technical=requirements=of=the=present=document=apply=under=the=environmental=profile=for=operation=of=the=equipmentf=which=shall=be=declared=by=the=manufacturerf=but=as=a=minimumf=shall=be=that=specified=in=the=test=conditions=contained=in=the=present=documenth=qhe=equipment=shall=comply=with=all=the=technical=requirements=of=the=present=document=which=are=identified=as=applicable=in=annex=A=at=all=times=when=operating=within=the=boundary=limits=of=the=declared=operational=environmental=profileh=jeasurements=shall=be=made=under=normal=test=conditions=bsee=clause=ohpc=and=alsof=where=statedf=under=extreme=test=conditions=bsee=clauses=ohqch=5.5 Test power source auring=testingf=the=equipment=shall=be=supplied=from=a=test=power=source=capable=of=producing=normal=and=extreme=test=voltagesh=qhe=internal=impedance=of=the=test=power=source=shall=be=low=enough=for=its=effect=on=the=test=results=to=be=negligibleh=cor=the=purpose=of=testing=the=power=source=voltage=shall=be=measured=at=the=input=terminals=of=the=equipmenth=auring=testingf=the=power=source=voltages=shall=be=maintained=within=a=tolerance=of=±m=B=relative=to=the=voltage=level=at=the=beginning=of=each=testh=5.6 Normal test conditions 5.6.1 Normal temperature and humidity qhe=normal=temperature=and=humidity=conditions=for=tests=shall=be=a=combination=of=temperature=and=humidity=within=the=following=rangest=• temperaturet=eko=°C=to=emo=°Cu=• relative=humidityt=lj=B=to=qo=Bh=then=it=is=impracticable=to=carry=out=the=tests=under=these=conditionsf=a=note=to=this=effectf=stating=the=ambient=temperature=and=relative=humidity=during=the=testsf=shall=be=added=to=the=test=reporth=5.6.2 Normal power sources 5.6.2.1 Mains voltage and frequency qhe=normal=test=voltage=for=equipment=to=be=connected=to=the=mains=shall=be=the=nominal=mains=voltageh=cor=the=purpose=of=the=present=documentf=the=nominal=voltage=shall=be=the=declared=voltage=or=any=of=the=declared=voltages=for=which=the=equipment=was=designedh=qhe=frequency=of=the=test=power=source=corresponding=to=the=AC=mains=shall=be=between=4s=ez=and=ok=ezh=5.6.2.2 Other power sources cor=operation=from=other=power=sources=or=types=of=battery=bprimary=or=secondarycf=the=normal=test=voltage=shall=be=that=declared=by=the=equipment=manufacturerh=SIST EN 302 617 V2.2.1:2018
ETSI ETSI EN 302 617 V2.2.1 (2017-11) 12 5.7 Extreme test conditions 5.7.1 Extreme temperatures cor=tests=at=extreme=temperaturesf=measurements=shall=be=made=in=accordance=with=clause=ohrf=at=a=lower=temperature=of=glj=°C=and=an=upper=temperature=of=eoo=°Ch=qhis=test=shall=be=performed=at=the=nominal=supply=voltage=as=defined=in=clause=ohphlh=5.
...












Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...