SIST EN ISO 7369:2020

SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN ISO 7369:2004
Cevovod - Kovinske cevi in cevni priključki - Slovar (ISO 7369:2020)
Pipework - Metal hoses and hose assemblies - Vocabulary (ISO 7369:2020)
Rohrleitungen - Metallschläuche und Metallschlauchleitungen - Vokabular (ISO
7369:2020)
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles - Vocabulaire (ISO 7369:2020)
Ta slovenski standard je istoveten z: EN ISO 7369:2020
ICS:
01.040.23 Tekočinski sistemi in sestavni Fluid systems and
deli za splošno rabo (Slovarji) components for general use
(Vocabularies)
23.040.10 Železne in jeklene cevi Iron and steel pipes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 7369
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 01.040.23; 23.040.70 Supersedes EN ISO 7369:2004
English Version
Pipework - Metal hoses and hose assemblies - Vocabulary
(ISO 7369:2020)
Tuyauteries - Tuyaux et tuyauteries métalliques Rohrleitungen - Metallschläuche und
flexibles - Vocabulaire (ISO 7369:2020) Metallschlauchleitungen - Vokabular (ISO 7369:2020)
This European Standard was approved by CEN on 28 April 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7369:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 7369:2020) has been prepared by Technical Committee ISO/TC 5 "Ferrous
metal pipes and metallic fittings" in collaboration with Technical Committee CEN/TC 342 “Metal hoses,
hose assemblies, bellows and expansion joints” the secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7369:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 7369:2020 has been approved by CEN as EN ISO 7369:2020 without any modification.

INTERNATIONAL ISO
STANDARD 7369
Fourth edition
2020-04
Pipework — Metal hoses and hose
assemblies — Vocabulary
Tuyauteries — Tuyaux et tuyauteries métalliques flexibles —
Vocabulaire
Reference number
ISO 7369:2020(E)
©
ISO 2020
ISO 7369:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 7369:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General . 1
3.2 Construction . 3
3.2.1 Metal hoses (stripwound or corrugated) . 3
3.2.2 Metal hose assemblies . 4
Annex A (informative) Equivalent terms in English, French, German and Dutch .5
Bibliography . 7
ISO 7369:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by the European Committee for Standardization (CEN) TechnicalCommittee
CEN/TC 342, Metal hoses, hose assemblies, bellows and expansion joints, in collaboration with ISO
Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 11, Metal
hoses and expansion joints, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 7369:2004), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— shift updated normative references into Bibliography;
— introduction of new definitions related to "design pressure", "metal braid strand", "braided braid"
and " nominal size of metal hose assembly";
— revision of definitions related to "maximum allowable pressure", "maximum allowable temperature"
and "minimum allowable temperature";
— update of Annex A to include French, German and Dutch terms and deletion of Annexes B, C, D and E.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

ISO 7369:2020(E)
Introduction
It was decided to produce a standard under the Vienna Agreement on technical cooperation between
ISO and the European Committee for Standardization CEN in order to maintain one document. The
opportunity was taken to re-format and add addi
...