SIST EN 3733-006:2008

SLOVENSKI STANDARD
01-julij-2008
$HURQDYWLND.RQHNWRURSWLþQLRNURJOLHQRNDQDOQLSULNOMXþHQVVDPR]DNOHSQLP
REURþHPVVWDOQRGHORYQRWHPSHUDWXURGRƒ&GHO3RGODJDNRQHNWRU
SULWUGLWHY]HQROXNQMRYVNODGX](1VWDQGDUG]DSURL]YRG
Aerospace series - Connector, optical, circular, single channel, coupled by self-locking
ring, operating temperature 150 °C continuous - Part 006: Receptacle, connector, jam
nut fixing for cable according to EN 4532, product standard
Luft- und Raumfahrt - Optischer Rundsteckverbinder einpolig, Schraubkupplung,
Betriebstemperatur 150 °C konstant - Teil 006: Fester Steckverbinder,
Einlochbefestigung für Kabel nach EN 4532, Produktnorm
Série aérospatiale - Connecteur optique circulaire monovoie, à accouplement par bague
filetée, température d'utilisation 150 °C continu - Partie 006 : Embase à fixation par écrou
pour câble EN 4532, norme de produit
Ta slovenski standard je istoveten z: EN 3733-006:2008
ICS:
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 3733-006
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 49.060
English Version
Aerospace series - Connector, optical, circular, single channel,
coupled by self-locking ring, operating temperature 150 °C
continuous - Part 006: Receptacle, connector, jam nut fixing for
cable according to EN 4532, product standard
Série aérospatiale - Connecteur optique circulaire Luft- und Raumfahrt - Optischer Rundsteckverbinder
monovoie, à accouplement par bague filetée, température
einpolig, Schraubkupplung, Betriebstemperatur 150 °C
d'utilisation 150 °C continu - Partie 006 : Embase à fixation konstant - Teil 006: Fester Steckverbinder,
par écrou pour câble EN 4532, norme de produit Einlochbefestigung für Kabel nach EN 4532, Produktnorm
This European Standard was approved by CEN on 16 September 2007.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3733-006:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terminology .4
4 Required characteristics.5
4.1 Dimensions and mass.5
4.2 Panel cut-out and mounting of connectors .6
4.3 Materials .6
4.4 Main general characteristics .6
4.5 Possible combinations of plugs and receptacles .7
5 Designation .7
6 Marking .7
7 Technical specification .7

Figures
Figure 1. 5
Figure 2. 6
Figure 3. 6

Tables
Table 1 — Compatible connectors and spare parts . 7
Table 2 — Additional test requirements applicable to this product standard .8

Foreword
This document (EN 3733-006:2008) has been prepared by the Aerospace and Defence Industries Association
of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
1 Scope
This standard specifies the characteristics of receptacle connectors with two hole fixing in the family of circular
single channel fibre optic connectors incorporating ferrules
...