SIST EN 50632-3-3:2017
(Main)Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers
Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers
This European Standard applies to transportable motor-operated electric tools and deals with the measurement procedure for planers and thicknessers for measurements of dust emission.
Motorbetriebene Elektrowerkzeuge – Staubmessverfahren – Teil 3-3: Besondere Anforderungen für transportable Abrichthobel und Dickenhobel
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 3-3: Exigences particulières pour les raboteuses et les dégauchisseuses transportables
L’article de la Partie 1 est applicable avec l'exception suivante:
Addition:
La présente partie de l'EN 50632 s'applique aux raboteuses et aux dégauchisseuses transportables destinées à raboter le bois.
Elektromotorna orodja - Postopek merjenja prahu - 3-3. del: Posebne zahteve za premične skobeljnike in debelinke
Ta evropski standard se uporablja za prenosna elektromotorna orodja ter obravnava postopek merjenja prahu za skobeljnike in debelinke.
General Information
Overview
EN 50632-3-3:2017 - "Electric motor-operated tools - Dust measurement procedure - Part 3-3" - defines particular requirements for measuring dust emissions from transportable planers and thicknessers. Published by CLC (CENELEC), this Part 3 standard is intended to be used in conjunction with EN 50632‑1:2015 (the general dust measurement requirements) and focuses on reproducible test conditions for determining inhalable and respirable wood dust emissions from portable planing equipment.
Key topics and technical requirements
- Scope: Applies to transportable motor-operated planers and thicknessers designed to plane wood.
- Test set-up: Tools are mounted on their working stand or on a test bench about 750 mm high.
- Test material: Planing of beech specimens with defined dimensions and maximum moisture content (wood humidity ≤ 12%).
- Cutting parameters:
- Cutting depth: 1 mm for both planers and thicknessers.
- Blades: Newly sharpened blades at the start of each test; manufacturer may allow unchanged blades for subsequent tests.
- Feed rate (thicknessers): As close as possible to 6 m/min.
- Operating cycles and workload:
- Transportable planers: each workpiece undergoes six planing operations (two passes per face and one on a narrow side); test cycles require 4 or 6 workpieces depending on planing width (≤ 260 mm or > 260 mm).
- Transportable thicknessers: four planing operations per workpiece; test cycles require 8 or 10 workpieces depending on width.
- Tests aim to perform the required number of planing operations within 10 minutes; cycle time may be extended and such extensions must be reported.
- Instrumentation and reporting: Instrumentation requirements follow Part 1; additional information to be reported includes any extension of cycle time and specified operating conditions.
Applications and who uses it
EN 50632-3-3:2017 is used by:
- Test laboratories performing standardized dust emission measurements for transportable planers and thicknessers.
- Manufacturers and R&D teams validating tool designs, dust extraction systems, and blade configurations.
- Health & safety professionals and occupational hygienists assessing exposures to inhalable/respirable wood dust and selecting control measures or PPE.
- Regulatory bodies and conformity assessors adopting harmonized test data for product safety documentation and national standards alignment.
Practical uses include product comparison, performance optimization of dust extraction, workplace risk assessment, and evidence-based selection of controls to reduce wood dust exposure.
Related standards
- EN 50632-1:2015 (Part 1 - general dust measurement procedure).
- Developed by CLC/TC 116 - Safety of motor‑operated electric tools.
Keywords: EN 50632-3-3:2017, dust measurement, transportable planers, thicknessers, wood dust, inhalable dust, respirable dust, CENELEC, test procedure.
Frequently Asked Questions
SIST EN 50632-3-3:2017 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers". This standard covers: This European Standard applies to transportable motor-operated electric tools and deals with the measurement procedure for planers and thicknessers for measurements of dust emission.
This European Standard applies to transportable motor-operated electric tools and deals with the measurement procedure for planers and thicknessers for measurements of dust emission.
SIST EN 50632-3-3:2017 is classified under the following ICS (International Classification for Standards) categories: 25.100.25 - Tools for planing and broaching machines; 25.140.20 - Electric tools. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 50632-3-3:2017 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 50632-3-3:2017 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Outils électriques à moteur - Procédure de mesure de la poussière - Partie 3-3: Exigences particulières pour les raboteuses et les dégauchisseuses transportablesElectric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers25.140.20Electric tools25.100.25Orodja za glajenje in ravnalna orodjaTools for planing and broaching machinesICS:Ta slovenski standard je istoveten z:EN 50632-3-3:2017SIST EN 50632-3-3:2017en01-marec-2017SIST EN 50632-3-3:2017SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 50632-3-3
January 2017 ICS 13.040.40; 79.120.10
English Version
Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 3-3: Exigences particulières pour les raboteuses et les dégauchisseuses
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 3-3: Besondere Anforderungen für transportable Abrichthobel und Dickenhobel This European Standard was approved by CENELEC on 2016-11-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Sebia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-3-3:2017 E SIST EN 50632-3-3:2017
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...