SIST EN 50632-2-19:2016/A1:2021
(Amendment)Electric motor-operated tools - Dust measurement procedure - Part 2-19: Particular requirements for jointers
Electric motor-operated tools - Dust measurement procedure - Part 2-19: Particular requirements for jointers
This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected.
This part of EN 50632 sets particular requirements for jointers.
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2 19: Besondere Anforderungen für Flachdübelfräsen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2 19: Exigences particulières pour les mortaiseuses
No scope available
Elektromotorna orodja - Postopek meritve prahu - 2-19. del: Posebne zahteve za skobeljnike - Dopolnilo A1
General Information
Relations
Overview
EN 50632-2-19:2016/A1:2021 is a CENELEC amendment that defines particular requirements for measuring dust emissions from jointers (motor-operated planing tools). It is part of the EN 50632 series covering dust measurement procedures for electric motor-operated tools. The standard applies to tools supplied from mains or batteries, with or without dust extraction, where mineral dust (including silica) or wood dust is expected. Amendment A1 (2021) updates operating conditions and adds a test orientation figure; this Part 2 is to be used in conjunction with EN 50632-1:2015.
Key topics and technical requirements
- Scope: Dust measurement procedure specific to jointers; applicable to mains- and battery-powered tools, both with and without extraction units.
- Test material & set-up:
- Chipboard: P2 in accordance with EN 312; density (610 ± 60) kg/m³; thickness (19 ± 1) mm; width (400 ± 2) mm.
- Workpiece mounted horizontally at a defined height relative to dust samplers (see 4.2).
- Grooves cut across the 400 mm width.
- Tool and cutting parameters:
- Disc cutter specified for chipboard, 4 mm thickness; a new cutter is used at the start of each of three tests.
- Cutting depth: 12 mm.
- Feed force: sufficient to ensure stable operation and good performance (operator-applied).
- Test cycle:
- One test cycle performs 15 grooves distributed over the working time.
- Typical guidance: 15 grooves in 10 minutes requires ~0.75 m/min working speed; time may be extended to achieve required grooves.
- Operator and orientation:
- Operator position and test layout defined by newly added Figure 101 (right-handed setup; mirror for left-handed tools).
- Regulatory timing:
- Amendment approved 2021-08-09; national implementation and withdrawal dates are specified in the foreword.
Applications - who uses this standard
- Manufacturers of jointers and woodworking power tools - to design, verify and claim dust emission performance.
- Independent test laboratories - to conduct repeatable, standardized dust emission measurements.
- Safety and compliance engineers - for conformity assessment against EU/ national requirements and to support CE marking documentation.
- Procurement and facility managers - to compare tools for workplace exposure control and dust extraction needs.
- Occupational health professionals - for exposure assessment and control measures for silica and wood dust.
Related standards
- EN 50632-1:2015 (use in conjunction with this Part 2)
- EN 50632 series (general dust measurement procedures for electric tools)
- CENELEC/CLC TC 116 guidance and national implementations
Keywords: EN 50632-2-19, dust measurement, jointers, electric motor-operated tools, silica dust, wood dust, dust extraction, CENELEC.
Frequently Asked Questions
SIST EN 50632-2-19:2016/A1:2021 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Electric motor-operated tools - Dust measurement procedure - Part 2-19: Particular requirements for jointers". This standard covers: This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for jointers.
This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for jointers.
SIST EN 50632-2-19:2016/A1:2021 is classified under the following ICS (International Classification for Standards) categories: 13.040.40 - Stationary source emissions; 25.100.25 - Tools for planing and broaching machines; 25.140.20 - Electric tools. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 50632-2-19:2016/A1:2021 has the following relationships with other standards: It is inter standard links to SIST EN 50632-2-19:2016. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase SIST EN 50632-2-19:2016/A1:2021 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2021
Elektromotorna orodja - Postopek meritve prahu - 2-19. del: Posebne zahteve za
skobeljnike - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-19: Particular
requirements for jointers
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2 19: Besondere
Anforderungen für Flachdübelfräsen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2 19:
Exigences particulières pour les mortaiseuses
Ta slovenski standard je istoveten z: EN 50632-2-19:2016/A1:2021
ICS:
25.100.25 Orodja za glajenje in Tools for planing and
ravnalna orodja broaching machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 50632-2-19:2016/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2021
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-19: Particular requirements for jointers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2 19: Exigences particulières pour les Teil 2 19: Besondere Anforderungen für Flachdübelfräsen
mortaiseuses
This amendment A1 modifies the European Standard EN 50632-2-19:2016; it was approved by CENELEC on 2021-08-09. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-19:2016/A1:2021 E
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to 4.3, “Operating conditions” .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...