SIST EN ISO 13807:2022
(Main)Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:2022)
Vitreous and porcelain enamels - Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry (ISO 13807:2022)
This document specifies a test method for the determination of the crack formation temperature of
enamels for the chemical industry by subjecting enamelled steel specimens to thermal shock using cold
water.
The value of the crack formation temperature measured according to this test method does not apply to
the finished component (see Annex A). It is a parameter of vitreous and porcelain enamels for comparing
the relative quality of different enamel formulations.
Emails und Emaillierungen - Bestimmung der Rissbildungstemperatur von Chemie-Emails beim Abschreckversuch (ISO 13807:2022)
Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Rissbildungstemperatur von Chemie-Emails durch Abschrecken emaillierter Stahlproben mit kaltem Wasser fest.
Der nach diesem Prüfverfahren gemessene Wert der Rissbildungstemperatur gilt nicht für das fertige Bauteil (siehe Anhang A). Er ist eine Kenngröße von Emails und Emaillierungen für den Vergleich der relativen Qualität verschiedener Emailrezepturen.
Émaux vitrifiés - Détermination de la température de fissuration par choc thermique d'émaux pour l'industrie chimique (ISO 13807:2022)
Le présent document spécifie une méthode d'essai pour la détermination de la température de fissuration des émaux pour l'industrie chimique en soumettant la surface d'éprouvettes d'acier émaillé à un choc thermique en utilisant de l'eau froide.
La valeur de la température de fissuration mesurée conformément à cette méthode d'essai ne s'applique pas au composant fini (voir Annexe A). Il s'agit d'un paramètre relatif aux émaux soumis à essai utilisé comme valeur comparative par rapport aux autres qualités d'émaux.
Steklasti in porcelanski emajli - Ugotavljanje temperature pokanja emajlov za kemično industrijo zaradi izpostavljenosti toplotnemu šoku (ISO 13807:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13807:2022
01-december-2022
Nadomešča:
SIST EN ISO 13807:2009
Steklasti in porcelanski emajli - Ugotavljanje temperature pokanja emajlov za
kemično industrijo zaradi izpostavljenosti toplotnemu šoku (ISO 13807:2022)
Vitreous and porcelain enamels - Determination of crack formation temperature in the
thermal shock testing of enamels for the chemical industry (ISO 13807:2022)
Emails und Emaillierungen - Bestimmung der Rissbildungstemperatur von Chemie-
Emails beim Abschreckversuch (ISO 13807:2022)
Émaux vitrifiés - Détermination de la température de fissuration par choc thermique
d'émaux pour l'industrie chimique (ISO 13807:2022)
Ta slovenski standard je istoveten z: EN ISO 13807:2022
ICS:
25.220.50 Emajlne prevleke Enamels
71.020 Proizvodnja v kemijski Production in the chemical
industriji industry
SIST EN ISO 13807:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13807:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 13807:2022
EN ISO 13807
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.220.50 Supersedes EN ISO 13807:2009
English Version
Vitreous and porcelain enamels - Determination of crack
formation temperature in the thermal shock testing of
enamels for the chemical industry (ISO 13807:2022)
Émaux vitrifiés - Détermination de la température de Emails und Emaillierungen - Bestimmung der
fissuration par choc thermique d'émaux pour Rissbildungstemperatur von Chemie-Emails beim
l'industrie chimique (ISO 13807:2022) Abschreckversuch (ISO 13807:2022)
This European Standard was approved by CEN on 22 October 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13807:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13807:2022
EN ISO 13807:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13807:2022
EN ISO 13807:2022 (E)
European foreword
This document (EN ISO 13807:2022) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and
other inorganic coatings, including for corrosion protection and corrosion testing of metals and alloys”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13807:2009.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13807:2022 has been approved by CEN as EN ISO 13807:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13807:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 13807:2022
INTERNATIONAL ISO
STANDARD 13807
Second edition
2022-10
Vitreous and porcelain enamels —
Determination of crack formation
temperature in the thermal shock
testing of enamels for the chemical
industry
Émaux vitrifiés — Détermination de la température de fissuration par
choc thermique d'émaux pour l'industrie chimique
Reference number
ISO 13807:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 13807:2022
ISO 13807:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13807:2022
ISO 13807:2022(E)
Contents Page
Foreword .iv
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 D e sig n at ion . 1
5 P r i nc iple . 2
6 A pp a r at u s . 2
7 S p e c i men s. 2
7.1 S hape and preparation of specimens . 2
7.2 N umber of specimens . 3
8 P r o c e du re .3
9 E xpression of results . 4
10 Te s t r ep or t . 4
Annex A (informative) Explanatory notes . 5
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 13807:2022
ISO 13807:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 262, Metallic and other inorganic coatings, including for corrosion protection and corrosion testing of
metals and alloys, in accordance with the Agreement on technical cooperation betwee
...
SLOVENSKI STANDARD
oSIST prEN ISO 13807:2022
01-marec-2022
Steklasti in porcelanski emajli - Ugotavljanje temperature pokanja emajlov za
kemično industrijo zaradi izpostavljenosti toplotnemu šoku (ISO/DIS 13807:2022)
Vitreous and porcelain enamels - Determination of crack formation temperature in the
thermal shock testing of enamels for the chemical industry (ISO/DIS 13807:2022)
Emails und Emaillierungen – Bestimmung der Rissbildungstemperatur von Chemie-
Emails beim Abschreckversuch (ISO/DIS 13807:2022)
Émaux vitrifiés - Détermination de la température de fissuration par choc thermique
d'émaux pour l'industrie chimique (ISO/DIS 13807:2022)
Ta slovenski standard je istoveten z: prEN ISO 13807
ICS:
25.220.50 Emajlne prevleke Enamels
71.020 Proizvodnja v kemijski Production in the chemical
industriji industry
oSIST prEN ISO 13807:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 13807:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 13807:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13807
ISO/TC 107 Secretariat: KATS
Voting begins on: Voting terminates on:
2022-01-19 2022-04-13
Vitreous and porcelain enamels — Determination of crack
formation temperature in the thermal shock testing of
enamels for the chemical industry
Émaux vitrifiés — Détermination de la température de fissuration par choc thermique d'émaux pour
l'industrie chimique
ICS: 25.220.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13807:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 13807:2022
ISO/DIS 13807:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 13807:2022
ISO/DIS 13807:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 1
5 Principle . 2
6 Apparatus . 2
7 Specimens. 2
7.1 Shape and preparation of specimens . 2
7.2 Number of specimens . 3
8 Procedure .3
9 Expression of results . 4
10 Test report . 4
Annex A (informative) Explanatory notes . 5
Bibliography . 6
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 13807:2022
ISO/DIS 13807:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part
3.
Draft International Standards adopted by the technical committees are circulated to the member
bodies for voting. Publication as an International Standard requires approval by at least 75 % of the
member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the
subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 13807 was prepared by Technical Committee ISO/TC 107, Metallic and other
inorganic coatings.
Annex A of this International Standard is for information only.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 13807:2022
DRAFT INTERNATIONAL STANDARD ISO/DIS 13807:2022(E)
Vitreous and porcelain enamels — Determination of crack
formation temperature in the thermal shock testing of
enamels for the chemical industry
1 Scope
This International Standard specifies a test method for the determination of the crack formation
temperature of enamels for the chemical industry by subjecting enamelled steel specimens to thermal
shock using cold water.
The value of the crack formation temperature measured according to this test method is not valid for
the finished component (see annex A). It is a parameter of vitreous and porcelain enamels for comparing
the relative quality of different enamel formulations.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this International Standard. For dated references, subsequent amendments
to, or revisions of, any of these publications do not apply. However, parties to agreements based on
this International Standard are encouraged to investigate the possibility of applying the most recent
editions of the normative documents indicated below. For undated references, the latest edition of the
normative document referred to applies. Members of ISO and IEC maintain registers of currently valid
International Standards.
ISO 2746, Vitreous and porcelain enamels — High voltage test
ISO 2808, Paints and varnishes — Determination of film thickness
IS0 3819, Laboratory glassware — Beakers.
ISO 19496-1, Vitreous and porcelain enamels — Terminology — Part 1: Terms and definitions
3 Terms and definitions
For the purposes of this Interna
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.