oSIST prEN ISO 11300-1:2025
(Main)Piping systems for rehabilitation of underground drains, sewers and water supply networks - Part 1: Polyethylene (PE) material (ISO/DIS 11300-1:2025)
Piping systems for rehabilitation of underground drains, sewers and water supply networks - Part 1: Polyethylene (PE) material (ISO/DIS 11300-1:2025)
This document specifies requirements and test methods for pipes and fittings which are part of piping systems for the rehabilitation by means of renovation and trenchless replacement of underground non-pressure and pressure drainage and sewerage networks and water supply networks, which transport water intended for human consumption, including raw water pipelines.
It is applicable to polyethylene (PE) pipes, fittings and assemblies, as manufactured and as installed. It is not applicable to the existing pipeline.
It is applicable to technique families for renovation:
— lining with continuous pipes;
— lining with close-fit pipes;
and technique families for trenchless replacement:
— pipe bursting and pipe extraction;
— horizontal directional drilling and impact moling.
and intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427 1:2019, Annex A.
When used with lining with continuous pipes, lining with close-fit pipes and trenchless replacement technique families, this document is applicable to:
PE solid wall single layered pipes, (nominal outside diameter, dn), including any identification stripes;
PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex E, where all layers have the same MRS rating.
Furthermore, when used with lining with continuous pipes and trenchless replacement this document is applicable to:
— PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as specified in Annex E.
This document is applicable to jointing by means of butt fusion and electrofusion and to fabricated and injection-moulded fittings and mechanical connections of PE.
Rohrleitungssysteme für die Sanierung von unterirdischen Entwässerungs-, Kanalisations- und Wasserversorgungsnetzen - Teil 1: Werkstoff Polyethylen (PE) (ISO/DIS 11300-1:2025)
Dieses Dokument legt Anforderungen an und Prüfverfahren für Rohre und Formstücke fest, die Teil von Rohrleitungssystemen für die Sanierung von unterirdischen drucklosen und druckbeaufschlagten Entwässerungsleitungen, Abwasserleitungen und Wasserversorgungsnetzen sind, die Wasser für den menschlichen Gebrauch befördern, einschließlich Rohwasser-Zuflussrohrleitungen, durch Renovierung und grabenlose Erneuerung.
Es gilt für Rohre, Formstücke und Bauteilkombinationen aus Polyethylen (PE) wie hergestellt und wie eingebaut. Es gilt nicht für bestehende Rohrleitungen.
Es gilt für Technikfamilien für die Renovierung:
- Rohrstrang-Lining;
- Close-Fit-Lining;
und Technikfamilien für die grabenlose Erneuerung:
- Berstverfahren und Rohrausziehverfahren;
- Horizontal-Spülbohrverfahren und Bodenverdrängungsverfahren.
und ist für den Einsatz bei einer Betriebstemperatur von 20 °C als Bezugstemperatur vorgesehen.
ANMERKUNG Für Anwendungsgebiete, in denen konstante Betriebstemperaturen von über 20 °C und bis 40 °C auftreten, siehe ISO 4427 1:2019, Anhang A.
Bei Verwendung mit Rohrstrang-Lining, Close-Fit-Lining und Technikfamilien der grabenlosen Erneuerung gilt dieses Dokument für:
- einschichtige Vollwandrohre aus PE (Nenn-Außendurchmesser, dn), einschließlich Identifizierungsstreifen;
- PE-Rohre mit koextrudierten Schichten auf der Außen- und/oder der Innenfläche des Rohres (Gesamt-Außendurchmesser, dn), wie in Anhang E festgelegt, wobei alle Schichten den gleichen MRS-Wert aufweisen.
Ferner gilt dieses Dokument bei Verwendung mit Rohrstrang-Lining und grabenloser Erneuerung für:
- PE-beschichtete Rohre, (Außendurchmesser, dn) mit einer abziehbaren, zusätzlichen thermoplastischen Schicht, anliegend auf der Außenfläche des Rohres („beschichtetes Rohr“), wie in Anhang E festgelegt.
Dieses Dokument gilt für das Verbinden durch Stumpfschweißen und Heizwendelschweißen und für handgefertigte Spritzgussformstücke und mechanische Anschlüsse aus PE.
Systèmes de canalisations pour la réhabilitation des branchements, des collecteurs d’assainissement et des réseaux d’alimentation en eau enterrés - Partie 1: Matériau polyéthylène (PE) (ISO/DIS 11300-1:2025)
Cevni sistemi za obnovo podzemnih odtokov, kanalizacije in vodovodnih omrežij - 1. del: Polietilen (PE) (ISO/DIS 11300-1:2025)
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2025
Cevni sistemi za obnovo podzemnih odtokov, kanalizacije in vodovodnih omrežij -
1. del: Polietilen (PE) (ISO/DIS 11300-1:2025)
Piping systems for rehabilitation of underground drains, sewers and water supply
networks - Part 1: Polyethylene (PE) material (ISO/DIS 11300-1:2025)
Rohrleitungssysteme für die Sanierung von unterirdischen Entwässerungs-,
Kanalisations- und Wasserversorgungsnetzen - Teil 1: Werkstoff Polyethylen (PE)
(ISO/DIS 11300-1:2025)
Systèmes de canalisations pour la réhabilitation des branchements, des collecteurs
d’assainissement et des réseaux d’alimentation en eau enterrés - Partie 1: Matériau
polyéthylène (PE) (ISO/DIS 11300-1:2025)
Ta slovenski standard je istoveten z: prEN ISO 11300-1
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 11300-1
ISO/TC 138/SC 8
Piping systems for rehabilitation
Secretariat: JISC
of underground drains, sewers and
Voting begins on:
water supply networks —
2025-01-03
Part 1:
Voting terminates on:
2025-03-28
Polyethylene (PE) material
ICS: 93.030; 91.140.80; 23.040.20; 23.040.45; 93.025
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 11300-1:2025(en)
ISO/DIS 11300-1:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO/DIS 11300-1:2025(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
3.1 General .3
3.2 Terms related to techniques .5
3.3 Terms related to characteristics.6
3.4 Terms related to product stages .9
3.5 Terms related to materials .9
3.6 Terms related to Service conditions .10
3.7 Terms related to Joints .11
4 Symbols and abbreviated terms.11
4.1 Symbols .11
4.2 Abbreviated terms . 12
5 Pipes .13
5.1 Materials . 13
5.1.1 General . 13
5.1.2 Virgin material . 13
5.1.3 Reprocessable material and recyclable material . 13
5.2 General characteristics . 13
5.2.1 Appearance . 13
5.2.2 Colour . 13
5.3 Material characteristics . 13
5.4 Geometric characteristics .14
5.5 Mechanical characteristics .14
5.6 Physical characteristics .14
5.7 Jointing.14
5.8 Marking . 15
5.9 Regional requirements for pipes . 15
6 Fittings .15
6.1 Materials . 15
6.2 General characteristics .16
6.3 Material characteristics .16
6.4 Geometric characteristics .16
6.5 Mechanical characteristics .16
6.6 Physical characteristics .16
6.7 Jointing.16
6.8 Marking .16
6.9 Regional requirements for fittings .16
7 Ancillary components . 16
8 Fitness for purpose . 17
8.1 Materials .17
8.2 General characteristics .17
8.3 Geometric characteristics .17
8.4 Mechanical characteristics .18
8.5 Sampling .18
8.6 Regional requirements for pipes .18
9 Installation practice .18
9.1 Preparatory work .18
9.2 Storage, handling and transport of pipes and fittings .19
iii
ISO/DIS 11300-1:2025(en)
9.3 Equipment .19
9.3.1 General .19
9.3.2 Butt fusion equipment and de-beading equipment . 20
9.3.3 Pipe skids/rollers .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.