SIST EN 15085-1:2023

SLOVENSKI STANDARD
oSIST prEN 15085-1:2021
01-september-2021
Železniške naprave - Varjenje železniških vozil in njihovih delov - 1. del: Splošno
Railway applications - Welding of railway vehicles and components - Part 1: General
Bahnanwendungen - Schweißen von Schienenfahrzeugen und -fahrzeugteilen - Teil 1:
Allgemeines
Applications ferroviaires - Soudage des véhicules et des composants ferroviaires - Partie
1 : Généralités
Ta slovenski standard je istoveten z: prEN 15085-1
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
oSIST prEN 15085-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15085-1:2021

---------------------- Page: 2 ----------------------
oSIST prEN 15085-1:2021


DRAFT
EUROPEAN STANDARD
prEN 15085-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2021
ICS 25.160.10; 45.060.01 Will supersede EN 15085-1:2007+A1:2013
English Version

Railway applications - Welding of railway vehicles and
components - Part 1: General
Applications ferroviaires - Soudage des véhicules et des Bahnanwendungen - Schweißen von
composants ferroviaires - Partie 1: Généralités Schienenfahrzeugen und -fahrzeugteilen - Teil 1:
Allgemeines
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 256.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15085-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15085-1:2021
prEN 15085-1:2021 (E)
European foreword
This document (prEN 15085-1:2021) has been prepared by Technical Committee CEN/TC 256 “Railway
applications” the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 15085-1:2007+A1:2013.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association.
3

---------------------- Page: 4 ----------------------
oSIST prEN 15085-1:2021
prEN 15085-1:2021 (E)
Introduction
Welding is a special process in the manufacture of railway vehicles and their parts. The required
provisions for this process are laid down in the standards series EN ISO 3834. The basis of these
provisions is the basic technical welding standards with respect to the special requirements for the
construction of railway vehicles.
This series of standards applies to welding of metallic materials in the manufacture and maintenance of
railway vehicles and their parts.
It describes the control for the welding process for railway vehicles and their components for new
manufacture and maintenance.
With respect to the railway environment, this series of standards defines the quality requirements for
the welding manufacturer to undertake new building and repair work.
Components: parts and subassemblies are assigned a classification level, based on their safety relevance.
According to these levels, qualifications for welding personnel of the manufacturer are specified.
This series provides an essential link between the weld performance class defined during design, the
quality of the weld, and the demonstration of the required quali
...