SIST EN ISO 18064:2005

SLOVENSKI STANDARD
SIST EN ISO 18064:2005
01-maj-2005
Plastomerni elastomeri - Nomenklatura in okrajšave (ISO 18064:2003)
Thermoplastic elastomers - Nomenclature and abbreviated terms (ISO 18064:2003)
Thermoplastische Elastomere - Nomenklatur und Kurzzeichen (ISO 18064:2003)
Élastomeres thermoplastiques - Nomenclature et termes abrégé (ISO 18064:2003)
Ta slovenski standard je istoveten z: EN ISO 18064:2005
ICS:
01.040.83 Gumarska industrija in Rubber and plastics
industrija polimernih industries (Vocabularies)
materialov (Slovarji)
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 18064:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18064:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 18064:2005
EUROPEAN STANDARD
EN ISO 18064
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS 01.040.83; 83.080.20
English version
Thermoplastic elastomers - Nomenclature and abbreviated
terms (ISO 18064:2003)
Élastomères thermoplastiques - Nomenclature et termes Thermoplastische Elastomere - Nomenklatur und
abrégé (ISO 18064:2003) Kurzzeichen (ISO 18064:2003)
This European Standard was approved by CEN on 3 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18064:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18064:2005
EN ISO 18064:2005 (E)






Foreword



The text of ISO 18064:2003 has been prepared by Technical Committee ISO/TC 45 "Rubber
and rubber products” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 18064:2005 by Technical Committee CEN/TC 249 "Plastics", the
secretariat of which is held by IBN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2005, and conflicting national
standards shall be withdrawn at the latest by August 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 18064:2003 has been approved by CEN as EN ISO 18064:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18064:2005


INTERNATIONAL ISO
STANDARD 18064
First edition
2003-09-01


Thermoplastic elastomers —
Nomenclature and abbreviated terms
Élastomères thermoplastiques — Nomenclature et termes abrégés




Reference number
ISO 18064:2003(E)
©
ISO 2003

---------------------- Page: 5 ----------------------

SIST EN ISO 18064:2005
ISO 18064:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 18064:2005
ISO 18064:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Generic terms and definitions . 1
3.1 TPE. 1
3.2 TP. 1
4 Nomenclature system. 2
5 Categories of thermoplastic elastomer . 2
5.1 TPA. 2
5.2 TPC. 2
5.3 TPO. 2
5.4 TPS. 2
5.5 TPU. 2
5.6 TPV. 2
5.7 TPZ. 2
6 Materials in each TPE category . 3
6.1 Polyamide TPEs (TPAs). 3
6.2 Copolyester TPEs (TPCs). 3
6.3 Olefinic TPEs (TPOs) . 3
6.4 Styrenic TPEs (TPSs). 3
6.5 Urethane TPEs (TPUs). 4
6.6 Dynamically vulcanized TPEs (TPVs) . 4
6.7 Miscellaneous material (TPZ). 4
Annex A (informative) Formerly used abbreviated terms . 5

© ISO 2003 — All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 18064:2005
ISO 18064:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 18064 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products.
iv © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 18064:2005
ISO 18064:2003(E)
Introduction
Thermoplastic elasto
...