SIST EN ISO 11111-5:2005

SLOVENSKI STANDARD
SIST EN ISO 11111-5:2005
01-maj-2005
Tekstilni stroji – Varnostne zahteve – 5. del: Stroji za pripravo za tkanje in pletenje
(ISO 11111-5:2005)
Textile machinery - Safety requirements - Part 5: Preparatory machinery to weaving and
knitting (ISO 11111-5:2005)
Textilmaschinen - Sicherheitsanforderungen - Teil 5: Vorbereitungsmaschinen für die
Weberei und Wirkerei (ISO 11111-5:2005)
Matériel pour l'industrie textile - Exigences de sécurité - Partie 5: Machines de
préparation au tissage et au tricotage (ISO 11111-5:2005)
Ta slovenski standard je istoveten z: EN ISO 11111-5:2005
ICS:
59.120.30 Statve. Tkalni stroji Looms. Weaving machines
59.120.40 Pletilni stroji Knitting machines
SIST EN ISO 11111-5:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 11111-5

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2005
ICS 59.120.30; 59.120.40 Supersedes EN ISO 11111:1995
English version
Textile machinery - Safety requirements - Part 5: Preparatory
machinery to weaving and knitting (ISO 11111-5:2005)
Matériel pour l'industrie textile - Exigences de sécurité - Textilmaschinen - Sicherheitsanforderungen - Teil 5:
Partie 5: Machines de préparation au tissage et au Vorbereitungs- maschinen für die Weberei und Wirkerei
tricotage (ISO 11111-5:2005) (ISO 11111-5:2005)
This European Standard was approved by CEN on 21 January 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11111-5:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 11111-5:2005 (E)





Foreword


This document (EN ISO 11111-5:2005) has been prepared by Technical Committee ISO/TC 72
"Textile machinery and machinery for dry-cleaning and industrial laundering" in collaboration
with Technical Committee CEN/TC 214 "Textile machinery and machinery for dry-cleaning and
industrial laundry", the secretariat of which is held by SNV.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2005, and conflicting national
standards shall be withdrawn at the latest by August 2005.

This document supersedes EN ISO 11111:1995.

This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).

For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this
document.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 11111-5:2005 has been approved by CEN as EN ISO 11111-5:2005 without any
modifications.

NOTE Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 3 ----------------------

EN ISO 11111-5:2005 (E)


ANNEX ZA
(normative)
List of ISO standards and corresponding EN Standards


ISO Corresponding to
ISO 9902-1 EN ISO 9902-1
ISO 9902-5 EN ISO 9902-5
ISO 11111-1:2005 EN ISO 11111-1:2005
ISO 13852:1996 EN 294:1992
CEI 60204-1:2000 EN 60204-1:1997
3

---------------------- Page: 4 ----------------------

EN ISO 11111-5:2005 (E)

ANNEX ZB
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC

This European Standard has been prepared under a mandate given to CEN by the European

Commission and the European Free Trade Association to provide a means to conforming to
Essential Requirements of the New Approach Directive Machinery Directive 98/37/EC amended
by Directive 98/79/EC.

Once this standard is cited in the Official Journal of the European Communities under that
Directive and has been implemented as a national standard in at least one Member State,
compliance with the normative clauses of this standard confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of
that Directive and associated EFTA regulations.

WARNING: Other requirements and other EU Directives may be applicable to the product(s)
falling within the scope of this standard.



4

---------------------- Page: 5 ----------------------

INTERNATIONAL ISO
STANDARD 11111-5
First edition
2005-02-15


Textile machinery — Safety
requirements —
Part 5:
Preparatory machinery to weaving and
knitting
Matériel pour l'industrie textile — Exigences de sécurité —
Partie 5: Machines de préparation au tissage et au tricotage





Reference number
ISO 11111-5:2005(E)
©
ISO 2005

---------------------- Page: 6 ----------------------

ISO 11111-5:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 7 ----------------------

ISO 11111-5:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 List of significant hazards. 1
5 Significant hazards and corresponding safety requirements and/or measures. 2
5.1 General. 2
5.2 Warping, beaming and assembly beaming machines . 2
5.3 Sizing equipment. 4
5.3.1 Common requirements of sizing machines . 4
5.3.2 Cylinder dryers for sizing lines . 4
5.3.3 Size baths. 6
5.4 Size kettles. 8
5.5 Storage equipment for warp beams. 10
6 Verification of the safety requirements and/or measures . 11
7 Information concerning machine use . 11
Bibliography . 12

© ISO 2005 – All rights reserved iii

---------------------- Page: 8 ----------------------

ISO 11111-5:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11111-5 was prepared by Technical Committee ISO/TC 72, Textile machinery and machinery for dry-
cleaning and industrial laundering, Subcommittee SC 8, Safety requirements for textile machinery.
This first edition of ISO 11111-5, together with ISO 11111-1, ISO 11111-2, ISO 11111-3, ISO 11111-4,
ISO 11111-6 and ISO 11111-7, cancels and replaces ISO 11111:1995, which has been technically revised.
ISO 11111 consists of the following parts, under the general title Textile machinery — Safety requirements:
 Part 1: Common requirements
 Part 2: Spinning preparatory and spinning machines
 Part 3: Nonwoven machinery
 Part 4: Yarn processing, cordage and rope manufacturing machinery
 Part 5: Preparatory machinery to weaving and knitting
 Part 6: Fabric manufacturing machinery
 Part 7: Dyeing and finishing machinery

iv © ISO 2005 – All rights reserved

---------------------- Page: 9 ----------------------

ISO 11111-5:2005(E)
Introduction
ISO 11111-1 to ISO 11111-7 were prepared simultaneously by ISO/TC 72 and CEN/TC 214 and adopted
under the Vienna Agreement in order to obtain identical standards on technical safety requirements for the
design and construction of textile machinery.
ISO 11111 as a whole is intended for use by any person concerned with the safety of textile machinery, for
example, textile machinery designers, manufacturers and systems integrators. It is also of interest to users of
textile machines and safety experts.
This document is a type C standard as stated in ISO 12100-1. The various parts of ISO 11111 deal with
significant hazards generated by machines used in the textile industry. The machinery concerned and the
extent to which hazards are covered are indicated in the scope of this standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence.
For hazards of machines and machine elements not dealt with in the relevant part of ISO 11111, the designer
is to perform a risk assessment according to ISO 14121 and evolve means for reducing the risk from
significant hazards.
This part of ISO 11111 is intended to be used in conjunction with ISO 11111-1. As far as possible, the
requirements of this part of ISO 11111 are treated by way of reference to Clauses 5 and 6 of ISO 11111-1.
Clause 5 of ISO 11111-1 contains safety requirements and/or measures for frequently occurring hazards of
textile machinery which apply whenever referred to in this part of ISO 11111, while Clause 6 describes
significant hazards and corresponding safety requirements and/or measures for certain machine elements and
their combinations (e.g. rollers), which also apply whenever referred to in this part of ISO 11111.
© ISO 2005 – All rights reserved v

---------------------- Page: 10 ----------------------

INTERNATIONAL STANDARD ISO 11111-5:2005(E)

Textile machinery — Safety requirements —
Part 5:
Preparatory machinery to weaving and knitting
1 Scope
This part of ISO 11111 is intended to be used in conjunction with ISO 11111-1. It specifies significant hazards
and corresponding safety requirements and/or measures for preparatory machinery to weaving and knitting.
By taking into account the scope of ISO 11111-1 as far as is relevant, this part of ISO 11111 is applicable to
all machinery, plant and related equipment intended to be used for warping, beaming, sizing, size preparation
and storage of warp beams, as specified in Clause 5.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 9902-1, Textile machinery — Noise test code — Part 1: Common requirements
ISO 9902-5, Textile machinery — Noise test code — Part 5: Weaving and knitting preparatory machinery
ISO 11111-1:2005, Textile machinery — Safety requirements — Part 1: Common requirements
ISO 13852:1996, Safety of machinery — Safety distances to prevent danger zones being reached by the
upper limbs
IEC 60204-1:2000, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
3 Terms and definitions
For the purposes of this part of ISO 11111, the terms and definitions given in ISO 11111-1 apply.
4 List of significant hazards
Significant hazards found in preparatory machines to weaving and knitting which are common with those
frequently occurring with other textile machines or with machine elements of other textile machines shall be
considered in accordance with ISO 11111-1:2005, Clauses 5 and 6, whenever referred to under the heading
“General safety requirements” in Clause 5 of this part of ISO 11111. Significant hazards which are particular to
preparatory machines to weaving and knitting are considered as “Specific hazards” in Clause 5 of this part of
ISO 11111.
© ISO 2005 – All rights reserved 1

---------------------- Page: 11 ----------------------

ISO 11111-5:2005(E)
Before using this part of ISO 11111, it is impo
...