SIST EN ISO 1043-3:2017

SLOVENSKI STANDARD
SIST EN ISO 1043-3:2017
01-januar-2017
1DGRPHãþD
SIST EN ISO 1043-3:2000
3ROLPHUQLPDWHULDOL6LPEROLLQNUDWLFHGHO0HKþDOD,62
Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:2016)
Kunststoffe - Kennbuchstaben und Kurzzeichen - Teil 3: Weichmacher (ISO 1043-
3:2016)
Plastiques - Symboles et abréviations - Partie 3: Plastifiants (ISO 1043-3:2016)
Ta slovenski standard je istoveten z: EN ISO 1043-3:2016
ICS:
01.075 Simboli za znake Character symbols
83.040.30 Pomožni materiali in aditivi Auxiliary materials and
za polimerne materiale additives for plastics
SIST EN ISO 1043-3:2017 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1043-3:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 1043-3:2017


EN ISO 1043-3
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2016
EUROPÄISCHE NORM
ICS 83.040.30; 83.080.01 Supersedes EN ISO 1043-3:1999
English Version

Plastics - Symbols and abbreviated terms - Part 3:
Plasticizers (ISO 1043-3:2016)
Plastiques - Symboles et termes abrégés - Partie 3: Kunststoffe - Kennbuchstaben und Kurzzeichen - Teil
Plastifiants (ISO 1043-3:2016) 3: Weichmacher (ISO 1043-3:2016)
This European Standard was approved by CEN on 19 September 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1043-3:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1043-3:2017
EN ISO 1043-3:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1043-3:2017
EN ISO 1043-3:2016 (E)
European foreword
This document (EN ISO 1043-3:2016) has been prepared by Technical Committee ISO/TC 61 “Plastics”
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be
withdrawn at the latest by May 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 1043-3:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1043-3:2016 has been approved by CEN as EN ISO 1043-3:2016 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 1043-3:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 1043-3:2017
INTERNATIONAL ISO
STANDARD 1043-3
Third edition
2016-10-15
Plastics — Symbols and abbreviated
terms —
Part 3:
Plasticizers
Plastiques — Symboles et termes abrégés —
Partie 3: Plastifiants
Reference number
ISO 1043-3:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 1043-3:2017
ISO 1043-3:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 1043-3:2017
ISO 1043-3:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Use of the symbols and abbreviated terms . 1
5 Schedule of terms . 2
Annex A (normative) List of symbols for individual components of abbreviated terms .6
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 1043-3:2017
ISO 1043-3:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 1, Terminology.
This third edition cancels and replaces the second edition (ISO 1043-3:1996), which has been technically
revised with the following changes:
— alternative CAS Registry Numbers have been added for some “octyl” plasticizers;
— a symbol for soya bean has been included in Annex A.
ISO 1043 consists of the following parts, under the general title Plastics — Symbols and abbreviated terms:
— Part 1: Basic polymers and their special characteristics
— Part 2: Fillers and reinforcing materials
— Part 3: Plasticizers
— Part 4: Flame retardants
iv © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 1043-3:2017
INTERNATIONAL STANDARD ISO 1043-3:2016(E)
Plastics — Symbols and abbreviated terms —
Part 3:
Plasticizers
1 Scope
This part of ISO 1043 provides uniform symbols for components of terms relating to plasticizers to
form abbreviated terms. It includes, in general, only those abbreviated terms that have come into
established use.
The purpose of this part of ISO 1043 is to prevent the occurrence of more than one abbreviated term
for a given plasticizer. The symbols are primarily intended to be convenient shorthand for forming
abbreviated terms for chemical names in publications and other written matter.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 472, Plastics — Vocabulary
ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and ISO 1043-1 apply.
4 Use of the symbols and abbreviated terms
4.1 The first appearance of an abbreviated term in a text shall be enclosed in parentheses and shall be
preceded by the chemical name written in full.
4.2 Only capital letters shall be used for the symbols.
4.3 The list comprises the abbreviated term, the commonly used name or name
...