SIST EN IEC 61554:2025

SLOVENSKI STANDARD
01-oktober-2025
Oprema za panelno vgradnjo - Električni merilni instrumenti - Vgradne mere (IEC
61554:2025)
Panel mounted equipment - Electrical measuring instruments - Dimensions for panel
mounting (IEC 61554:2025)
Geräte zum Einbau in Warten – Elektrische Messgeräte – Maße für den Warteneinbau
(IEC 61554:2025)
Appareils montés en tableaux - Instruments de mesure électriques - Dimensions pour le
montage en tableaux (IEC 61554:2025)
Ta slovenski standard je istoveten z: EN IEC 61554:2025
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61554

NORME EUROPÉENNE
EUROPÄISCHE NORM July 2025
ICS 17.220.20
English Version
Panel mounted equipment - Electrical measuring instruments -
Dimensions for panel mounting
(IEC 61554:2025)
Appareils montés en tableaux - Instruments de mesure Geräte zum Einbau in Warten - Elektrische Messgeräte -
électriques - Dimensions pour le montage en tableaux Maße für den Warteneinbau
(IEC 61554:2025) (IEC 61554:2025)
This European Standard was approved by CENELEC on 2025-06-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61554:2025 E
European foreword
The text of document 85/949/FDIS, future edition 2 of IEC 61554, prepared by TC 85 "Measuring
equipment for electrical and electromagnetic quantities" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61554:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-07-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-07-31
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61554:2025 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
ISO 2768-1 - General tolerances -- Part 1: Tolerances EN 22768-1 -
for linear and angular dimensions without
individual tolerance indications

IEC 61554 ®
Edition 2.0 2025-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Panel mounted equipment – Electrical measuring instruments – Dimensions for
panel mounting
Appareils montés en tableaux – Instruments de mesure électriques –
Dimensions pour le montage en tableaux

ICS 17.220.20  ISBN 978-2-8327-0381-6

IEC 61554:2025-05(en-fr)
– 2 – IEC 61554:2025 © IEC 2025
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 6
4.1 General . 6
4.2 Instrument size designation . 6
4.3 Dimensions of the cut-out . 6
4.4 Individual cut-out mounting . 6
4.5 Common cut-out mounting . 7
Annex A (normative) Dimensions for instruments with round housing . 11
A.1 General . 11
A.2 Overview. 11
A.3 Requirements . 11
A.3.1 General . 11
A.3.2 Instrument size designation . 11
A.3.3 Individual cut-out mounting . 11

Figure 1 – Square housing . 7
Figure 2 – Rectangular lateral housing . 7
Figure 3 – Rectangular upright housing . 8
Figure 4 – Common cut-out mounting . 8
Figure A.1 – Round housing with a square bezel. 12
Figure A.2 – Round housing with a rectangular bezel type 1 . 13
Figure A.3 – Round housing with a rectangular bezel type 2 . 15

Table 1 – Sizes and tolerances . 9
Table A.1 – Sizes and tolerances of round housing with a square bezel . 12
Table A.2 – Sizes and tolerances of round housing with a rectangular bezel type 1 . 14
Table A.3 – Sizes and tolerances of round housing with a rectangular bezel type 2 . 15

IEC 61554:2025 © IEC 2025 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PANEL MOUNTED EQUIPMENT –
ELECTRICAL MEASURING INSTRUMENTS –
DIMENSIONS FOR PANEL MOUNTING
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61554 has been prepared by IEC technical committee 85: Measuring equipment for
electrical and electromagnetic quantities. It is an International Standard.
This second edition cancels and replaces the first edition published in 1999. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Add more sizes and tolerances of instruments and some practical information for panel
mounting which were not mentioned in IEC 61554:1999;
b) Modify several current sizes and tolerance of instruments;
c) Update the figures in Annex A;
d) Change Annex A from informative to normative.

– 4 – IEC 61554:2025 © IEC 2025
The text of this International Standard is based on the following do
...