SIST EN 1106:2022+A1:2024
(Main + Amendment)Manually operated taps for gas burning appliances
Manually operated taps for gas burning appliances
EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for
manually operated taps and presetting taps for burners and appliances burning one or more gaseous
fuels, hereafter referred to as “taps”.
This document is applicable to taps with declared maximum inlet pressures up to and including 50 kPa
and of nominal connection sizes up to and including DN 50 for use with one or more fuel gases.
Addition:
This document is not applicable to:
a) manual operated shut-off valves conforming to EN 331:2015;
b) controls which use auxiliary energy (e.g. electrical energy supplied externally).
The 4th paragraph of EN 13611:2019, Clause 1 is removed.
Handbetätigte Einstellgeräte für Gasgeräte
Dieses Dokument legt Anforderungen an die Sicherheit sowie Bau- und Funktionsanforderungen an handbetätigte und voreingestellte Einstellgeräte fest, die für die Verwendung mit Gasgeräten sowie gleichwertige Verwendungszwecke vorgesehen sind und im Folgenden als „Einstellgeräte“ bezeichnet werden.
Dieses Dokument gilt für Einstellgeräte mit Nenn-Anschlussmaßen bis einschließlich DN 50, für die ein maximaler Eingangsdruck bis einschließlich 50 kPa (500 mbar) festgelegt ist und die für den Einsatz mit einem oder mehreren Brenngasen nach EN 437 vorgesehen sind.
Dieses Dokument ist nicht anwendbar auf:
a) handbetätigte Absperrarmaturen nach EN 331;
b) Regel- und Steuergeräte, die Hilfsenergie nutzen (z. B. von außen zugeführte elektrische Energie);
c) eine Bewertung der Regeleinrichtung in Bezug auf Performance Level (PL) und Sicherheits-Integritätslevel (SIL).
Robinets à commande manuelle pour appareils à gaz
L’article 1 de la norme EN13611 :2019 s’applique avec la modification et l’addition suivantes :
Modification :
Le 1er paragraphe de l’article 1 de la norme EN13611 :2019 est remplacé par ce qui suit :
Le présent document spécifie les caractéristiques de sécurité, de construction et de fonctionnement ainsi ques les essais applicables aux robinets à commande manuelle et des organes de préréglage destinés aux appareils utilisant les combustibles gazeux et utilisation similaire, ci-après désignés « robinets ».
Ce document s’applique aux robinets avec des pressions amont maximales déclarées inférieures ou égales à 50 kPa , de diamètres nominaux de raccordement inférieurs ou égaux à DN 50 et utilisés avec un ou plusieurs combustibles gazeux .
Addition :
Le présent document ne s’applique pas :
a) aux robinets de sectionnement à commande manuelle visés par l’EN 331 :2015 ;
b) aux commandes utilisant une énergie auxiliaire (par exemple, énergie électrique alimentée par une source externe) ;
Le 4ième paragraphe de l’article 1 de la EN 13611 :2019 est supprimé.
Ročne pipe za plinske aparate (vključno z dopolnilom A1)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN 1106:2022
Ročne pipe za plinske aparate (vključno z dopolnilom A1)
Manually operated taps for gas burning appliances
Handbetätigte Einstellgeräte für Gasgeräte
Robinets à commande manuelle pour appareils à gaz
Ta slovenski standard je istoveten z: EN 1106:2022+A1:2023
ICS:
23.060.99 Drugi ventili Other valves
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 1106:2022+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 23.060.40 Supersedes EN 1106:2022
English Version
Manually operated taps for gas burning appliances
Robinets à commande manuelle pour appareils à gaz Handbetätigte Einstellgeräte für Gasgeräte
This European Standard was approved by CEN on 8 August 2022 and includes Amendment approved by CEN on 11 October
2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1106:2022+A1:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Classification . 15
4.1 Classes of control . 15
4.2 Groups of control . 15
4.3 Classes of control functions . 15
4.4 Types of DC supplied controls . 15
5 Units of measurement and test conditions . 15
6 Design and Construction . 15
6.1 General . 15
6.2 Mechanical parts of the control . 15
6.2.1 Appearance . 15
6.2.2 Holes . 15
6.2.3 Breather holes . 15
6.2.4 Screwed fastenings . 15
6.2.5 Jointing . 15
6.2.6 Moving parts . 16
6.2.7 Sealing caps . 16
6.2.8 Dismantling and reassembly . 16
6.2.9 Auxiliary canals and orifices . 16
6.2.10 Presetting device . 16
6.2.101 Operating parts of taps . 16
6.3 Materials . 16
6.3.1 General material requirements . 16
6.3.2 Housing . 16
6.3.3 Zinc alloys . 16
6.3.4 Springs . 16
6.3.5 Resistance to corrosion and surface protection. 16
6.3.6 Impregnation . 17
6.3.7 Seals for glands for moving parts . 17
6.3.101 Tap closure member . 17
6.4 Gas connections. 17
6.5 Electrical parts of the control. 17
6.6 Protection against internal faults for the purpose of functional safety . 17
6.101 Component parts . 17
6.101.1 General . 17
6.101.2 Turning angles . 17
6.101.3 Lubrication . 18
6.101.4 Stops . 18
6.101.5 Safety lock . 18
6.101.6 Bearing seal . 19
6.101.7 Taper angle . 19
6.101.8 Open and closed position of a tap . 19
6.101.9 Compensation means for taps . 19
6.101.10 Spring effect in taps . 19
7 Performance . 19
7.1 General . 19
7.2 Leak-tightness . 19
7.3 Torsion and bending . 19
7.4 Rated flow rate . 19
7.4.1 Requirements . 19
7.4.2 Test . 19
7.4.3 Conversion of air flow rate . 19
7.5 Durability . 20
7.6 Performance tests for electronic controls . 20
7.7 Long-term performance for electronic controls . 20
7.8 Data exchange . 20
7.101 Operating torque and force . 20
7.101.1 Requirements for operating torque . 20
7.101.2 Test for operating torque . 20
7.101.3 Requirements for operating force . 20
7.101.4 Test for operating force . 21
7.101.5 Requirements for operating torque for safety lock . 21
7.101.6 Test for operating torque for safety lock . 21
7.102 Endurance . 21
7.102.1 Requirement . 21
7.102.2 Endurance test . 21
8 Electrical requirements . 22
9 Electromagnetic compatibility (EMC). 22
10 Marking, instructions . 22
10.1 Marking. 22
10.2 Instructions . 23
10.3 Warning notice . 23
Annex A (informative) Abbreviations and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.