SIST EN ISO 12100-1:2004/A1:2010

SLOVENSKI STANDARD
SIST EN ISO 12100-1:2004/A1:2010
01-marec-2010
9DUQRVWVWURMHY2VQRYQLSRMPLVSORãQDQDþHODQDþUWRYDQMDGHO2VQRYQD
WHUPLQRORJLMDPHWRGRORJLMD'RSROQLOR,62$PG
Safety of machinery - Basic concepts, general principles for design - Part 1: Basic
terminology, methodology - Amendment 1 (ISO 12100-1:2003/Amd 1:2009)
Sicherheit von Maschinen - Grundbegriffe, allgemeine Gestaltungsleitsätze - Teil 1:
Grundsätzliche Terminologie, Methodologie - Änderung 1 (ISO 12100-1:2003/Amd
1:2009)
Sécurité des machines - Notions fondamentales, principes généraux de conception -
Partie 1: Terminologie de base, méthodologie - Amendement 1 (ISO 12100-1:2003/Amd
1:2009)
Ta slovenski standard je istoveten z: EN ISO 12100-1:2003/A1:2009
ICS:
01.040.13 Varstvo okolja in zdravja. Environment and health
Varnost (Slovarji) protection. Safety
(Vocabularies)
13.110 Varnost strojev Safety of machinery
SIST EN ISO 12100-1:2004/A1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12100-1:2004/A1:2010

---------------------- Page: 2 ----------------------

SIST EN ISO 12100-1:2004/A1:2010
EUROPEAN STANDARD
EN ISO 12100-1:2003/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2009
ICS 01.040.13; 13.110
English Version
Safety of machinery - Basic concepts, general principles for
design - Part 1: Basic terminology, methodology - Amendment 1
(ISO 12100-1:2003/Amd 1:2009)
Sécurité des machines - Notions fondamentales, principes Sicherheit von Maschinen - Grundbegriffe, allgemeine
généraux de conception - Partie 1: Terminologie de base, Gestaltungsleitsätze - Teil 1: Grundsätzliche Terminologie,
méthodologie - Amendement 1 (ISO 12100-1:2003/Amd Methodologie - Änderung 1 (ISO 12100-1:2003/Amd
1:2009) 1:2009)
This amendment A1 modifies the European Standard EN ISO 12100-1:2003; it was approved by CEN on 13 May 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12100-1:2003/A1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12100-1:2004/A1:2010
EN ISO 12100-1:2003/A1:2009 (E)
Contents Page
Foreword .3
Annex ZA (informative)  Relationship between this International Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative)  Relationship between this International Standard and the Essential
Requirements of EU Directive 2006/42/EC .5

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12100-1:2004/A1:2010
EN ISO 12100-1:2003/A1:2009 (E)
Foreword
This document (EN ISO 12100-1:2003/A1:2009) has been prepared by Technical Committee ISO/TC 199
"Safety of machinery" in collaboration with Technical Committee CEN/TC 114 “Safety of machinery” the
secretariat of which is held by DIN.
This Amendment to the European Standard EN ISO 12100:2003 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and
conflicting national standards shall be withdrawn at the latest by December 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directives.
For relationship with EC Directives, see informative Annexes ZA and ZB, which are integral parts of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 12100-1:2003/Amd 1:2009 has been approved by CEN as a EN ISO 12100-1:2003/A1:2009
without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 12100-1:2004/A1:2010
EN ISO 12100-1:2003/A1:2009 (E)
Annex ZA
(informative)


Relationship between this International Standard and the Essential
Requirements of EU Directive 98/37/EC
This International Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 98/37/EC.

Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements of that Directive and associated EFTA regulations.

WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.

4

---------------------- Page: 6 -------
...