iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 14382:2019+A1:2025

(Main)

Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)

Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)

Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic
functional checks it is common to refer to national regulations/standards where existing or
users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable
expected failures in terms of “fail close” behaviour, but it should be consider that there are other types
of failures whose consequences cannot bring to the same reactions (these risks are covered via
redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in
use / maintenance.
In this document, both safety shut-off devices that can be classified as “safety accessories” by
themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off
devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff
device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered.
Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements,
test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are
suitable to ensure an equivalent level of reliability.
Some clauses of this standard should be re-considered at the time when characteristics for nonconventional
gases will be available.
Gas safety shut-off devices according to this European standard do not have their own source of ignition
and therefore are not within the scope of European Directive 2014/34/EU. Any additional component
(e.g. proximity switch, travel transducer etc.) should be independently considered in the framework of
assemblies per ATEX Guideline to the application of Directive 2014/34/EU of the European Parliament
and of the Council of 26nd February 2014, edition December 2017, §§42 and 43.
The document includes also environmental considerations.

Gas-Sicherheitsabsperreinrichtungen für Eingangsdrücke bis 10 MPa (100 bar)

No scope available

Dispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'à 10 MPa (100 bar)

No scope available

Plinske varnostne zaporne naprave za vstopne tlake do 10 MPa (100 bar) (vključno z dopolnilom A1)

General Information

Status
Published
Publication Date
07-Jan-2025
ICS
23.060.40 - Pressure regulators
Technical Committee
DPL - Gas supply
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Nov-2024
Due Date
19-Jan-2025
Completion Date
08-Jan-2025
Directive
2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
Mandate
M/601 - COMMISSION IMPLEMENTING DECISION of 1.3.2024 on a standardisation request to the European Committee for Standardization and the European Committee for Electrotechnical Standardization as regards pressure equipment and assemblies in support of Directive 2014/68/EU of the European Parliament and of the Council
Ref Project
EN 14382:2019+A1:2024 - Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)

Relations

Replaces
SIST EN 14382:2019 - Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
Effective Date
01-Feb-2025
Merged From
SIST EN 14382:2019/kFprA1:2023 - Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
Effective Date
03-Jul-2024

Buy Standard

EN 14382:2019+A1:2025EN 14382:2019+A1:2025
PreviousNext
Standard
EN 14382:2019+A1:2025
English language
77 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2025
Nadomešča:
SIST EN 14382:2019
Plinske varnostne zaporne naprave za vstopne tlake do 10 MPa (100 bar) (vključno
z dopolnilom A1)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
Gas-Sicherheitsabsperreinrichtungen für Eingangsdrücke bis 10 MPa (100 bar)
Dispositifs de sécurité pour postes et installations de détente-régulation de pression de
gaz - Clapets de sécurité pour pressions amont jusqu'à 10 MPa (100 bar)
Ta slovenski standard je istoveten z: EN 14382:2019+A1:2024
ICS:
23.060.40 Tlačni regulatorji Pressure regulators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 14382:2019+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2024
EUROPÄISCHE NORM
ICS 23.060.40 Supersedes EN 14382:2019
English Version
Gas safety shut-off devices for inlet pressure up to 10 MPa
(100 bar)
Dispositifs de sécurité pour postes et installations de Gas-Sicherheitsabsperreinrichtungen für
détente-régulation de pression de gaz - Clapets de Eingangsdrücke bis 10 MPa (100 bar)
sécurité pour pressions amont jusqu'à 10 MPa (100
bar)
This European Standard was approved by CEN on 23 April 2019 and includes Amendment approved by CEN on 22 October
2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14382:2019+A1:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 8
3.1 General terms and definition of type of gas safety shut-off devices . 8
3.2 Terms and definition of components of safety devices . 9
3.3 Terms, symbols and definitions related to the functional performance . 15
3.4 Possible values of all variables. 16
3.5 Terms, symbols and definitions related to the set value of the trip pressure . 16
3.6 Terms, symbols and definitions related to the flow . 17
3.7 Terms, symbols and definitions related to accuracy and some other performances . 17
3.8 Terms, symbols and definitions related to the design and tests . 18
3.9 Summary of symbols, terms, subclauses and units. 20
4 Construction requirements . 21
4.1 Basic requirements . 21
4.2 Materials . 24
4.3 Strength of housings and other parts. 25
4.4 Strength of elastomeric diaphragms . 28
5 Functional and characteristic requirements . 29
5.1 General . 29
5.2 Accuracy group . 30
5.3 Response time . 31
5.4 Relatching difference and unlatching . 31
5.5 Closing force . 31
5.6 Endurance and accelerated ageing . 32
5.7 Strength of the trip mechanism, valve seat and closing member against the dynamic
impact of flowing gas . 32
5.8 Antistatic characteristics . 32
5.9 Flow coefficient . 32
5.10 Final visual inspection . 32
6 Testing . 33
6.1 General . 33
6.2 Tests . 33
6.3 Type test . 34
6.4 Selection of test samples . 34
6.5 Routine tests . 35
6.6 Production surveillance . 35
7 Test and verification methods . 35
7.1 Dimensional check and visual inspection . 35
7.2 Materials check . 35
7.3 Verification of the strength of parts under pressure . 35
7.4 Verification of the strength of parts transmitting actuating forces . 35
7.5 Shell and inner metallic partition walls strength test . 36
7.6 Alternative shell and inner metallic partition walls strength test . 36
7.7 External tightness test . 36
7.8 Internal sealing test . 37
7.9 Test method and acceptance criteria to verify the antistatic characteristics . 37
7.10 Accuracy group . 37
7.11 Response time . 42
7.12 Relatching difference and unlatching . 43
7.13 Verification of closing force . 44
7.14 Endurance and accelerated ageing . 44
7.15 Resistance to gas of non-metallic parts . 44
7.16 Verification of the strength of the trip mechanism, valve seat and closing member
against dynamic impact of flowing gas . 44
7.17 Final visual inspection . 45
8 Field surveillance . 45
9 Documentation . 46
9.1 Documentation related to type test . 46
9.2 Documentation related to the routine tests . 46
9.3 Documentation related to production surveillance in accordance with 6.6 . 46
9.4 Operating instructions . 47
9.5 Information on sizing . 47
10 Marking . 48
10.1 General requirements . 48
10.2 Basic requirements . 48
10.3 Other additional requirements . 48
10.4 Markings for the various connections. 49
10.5 Identification of auxiliary devices . 49

11 Packaging and transportation of finished product . 49
Annex A (informative) Ice formation . 50
A.1 General . 50
A.2 Requirements . 50
A.3 Tests . 50
)
Annex B (informative) Compliance evaluation . 51
B.1 General . 51
B.2 Introduction. 51
B.3 Procedure . 51
B.4 Manufacturer’s compliance evaluation .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 334:2019+A1:2025(Main)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
EN 334:2019+A1:2024

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12186:2015(Main)
Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
EN 12186:2014

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flowrate is equal to or less than 200 m³/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorisation systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European standard are based on the physical and chemical data of gaseous fuels - including non-conventional gases - in accordance with Table 1 of EN 437:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.
This European Standard specifies common basic principles for the gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation shall take precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 gives:
-  clarification of all legislations/regulations applicable in a member state;
-  if appropriate, more restrictive national requirements;
-  a national contact point for the latest information.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12279:2000/A1:2005(Amendment)
Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements
EN 12279:2000/A1:2005
  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12279:2000(Main)
Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements
EN 12279:2000

This European Standard contains the relevant functinal requirements for gas pressure regulating installations forming a part of the service lines in gas supply systems.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14382:2019/kFprA1:2023(Amendment)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
EN 14382:2019/FprA1

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14382:2005/kprA1:2008(Amendment)
Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
EN 14382:2005/prA1

Tolerance of 9 months before UAP per CEN/TC 235 res. C03/2006.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 12186:2025(Main)
Gas infrastructure - Gas pressure control stations for transmission and distribution - Functional requirements
prEN 12186

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flow rate is equal to or less than 200 m3/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
NOTE   For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European Standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorization systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European Standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European Standard are based on the physical and chemical data of gaseous fuels – including non-conventional gases – in accordance with Table 1 of EN 437:2003+A1:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European Standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.

  • Draft
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 334:2019/kFprA1:2024(Amendment)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
EN 334:2019/FprA1

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 334:2005/kprA1:2008(Amendment)
Gas pressure regulators for inlet pressures up to 100 bar
EN 334:2005/prA1

Tolerance of 9 months requested before UAP per CEN/TC 235 C02/2006.

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14071:2025(Main)
LPG equipment and accessories - Pressure relief valves for LPG pressure vessels - Ancillary equipment
EN 14071:2024

This document specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This document addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in EN 14129:2014.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day