SIST EN 61067-1:1998

SLOVENSKI STANDARD
SIST EN 61067-1:1998
01-junij-1998
Specification for glass and glass polyester fibre woven tapes - Part 1: Definitions,
classification and general requirements (IEC 61067-1:1991)
Specification for glass and glass polyester fibre woven tapes -- Part 1: Definitions,
classification and general requirements
Bestimmung für gewebte Bänder aus Textilglas oder Textilglas und Polyesterfilamenten -
- Teil 1: Definitionen, Klassifizierung und allgemeine Anforderungen
Spécification pour rubans tissés en fibres de verre ou en fibres de verre et de polyester --
Partie 1: Définitions, classification et prescriptions générales
Ta slovenski standard je istoveten z: EN 61067-1:1997
ICS:
01.040.29 Elektrotehnika (Slovarji) Electrical engineering
(Vocabularies)
29.035.30 .HUDPLþQLLQVWHNOHQL Ceramic and glass insulating
L]RODFLMVNLPDWHULDOL materials
SIST EN 61067-1:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61067-1:1998

---------------------- Page: 2 ----------------------

SIST EN 61067-1:1998

---------------------- Page: 3 ----------------------

SIST EN 61067-1:1998

---------------------- Page: 4 ----------------------

SIST EN 61067-1:1998

---------------------- Page: 5 ----------------------

SIST EN 61067-1:1998

---------------------- Page: 6 ----------------------

SIST EN 61067-1:1998
NORME
CEI
INTERNATIONALE
IEC
61067-1
INTERNATIONAL
Première édition
STANDARD
First edition
1991-05
Spécification pour rubans tissés en fibres
verre ou
de en fibres de verre et de polyester
Partie 1:
Définitions, classification et prescriptions
générales
Specification for glass and glass polyester fibre
woven tapes
Part 1:
Definitions, classification and general requirements
© IEC 1991 Droits de reproduction réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
H
PRICE CODE
International Electrotechnical Commission
IEC Me}1fayHapoAHaR 371eKTpoTeXHwleCHan HOMNCCHR
Pour prix, voir catalogue en vigueur
• • For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 61067-1:1998
1067-1
© IEC - 3 -
INTERNATIONAL ELECTROTECHNICAL COMMISSION
SPECIFICATION FOR GLASS AND GLASS POLYESTER
FIBRE WOVEN TAPES
Part 1: Definitions, classification and general requirements
FOREWORD
1) The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on
which all the National Committees having a special interest therein are represented, express, as nearly as
possible, an international consensus of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National
Committees in that sense.
3) In order to promote international unification, the IEC expresses the wish that all National Committees
should adopt the text of the IEC recommendation for their national rules in so far as national conditions will
permit. Any divergence between the IEC recommendation and the corresponding national rules should, as
far as possible, be clearly indicated in the la tter.
4) The IEC has not laid down any procedure concerning marking as an indication of approval and has no
responsibility when an item of equipment is declared to comply with one of its recommendations.
This part
of International Standard 1067 has been prepared by Sub-Committee 15C: Speci-
fications, of IEC Technical Committee No. 15: Insulating materials.
The text of this part
is based on the following documents:
Six Months' Rule Report on Voting
15C(CO)234
15C(CO)248
Full information on the voting for the approval of this pa rt can be found in the Voting
Report indicated in the above table.

---------------------- Page: 8 ----------------------

SIST EN 61067-1:1998
1067-1 © IEC – 5 –
INTRODUCTION
The International Stand
ard IEC 1067 deals with glass and glass polyester fibre woven tapes.
The standard will comprise the following parts:
rt
Pa 1: Definitions, classification and general requirements.
Part 2: Methods of test.
Part 3: Specifications for individual materials.

---------------------- Page: 9 ----------------------

SIST EN 61067-1:1998
- 7 -
1067-1 ©IEC
SPECIFICATION FOR GLASS AND GLASS POLYESTER
FIBRE WOVEN TAPES
Part 1: Definitions, classification and general requirements
1 General
1.1 Scope
of IEC 1067 specifies requirements for loomstate, continuous filament tapes woven on
This part
conventional or shuttleless looms from either glass fibres or a combination of glass and polyester
fibres.
ranges of nominal sizes covered by this standard are:
The
width: 10 mm to 50 mm,
0,05 mm to 0,40 mm.
thickness:
1.2 Normative reference
The following standard contains provisions which, through reference in this text, constitute provi-
of IEC 1067. At the time of publication, the edition indicated was valid. All
sions of this part
of IEC 1067 are
ies to agreement based on this part
standards are subject to revision, and part
encouraged to investigate the possibility of applying the most recent edition of the standard indi-
cated below. Members of IEC and ISO maintain registers of currently valid International
Standards.
Standard colours for insulation for low-frequency cables and wires.
IEC 304: 1982,
2 Definitions
For the purpose of this part, the following definitions apply.
the picking
2.1 pick: Weft thread or group of threads inserted in a fabric by one traverse of
mechanism between two consecutive beat-ups.
2.2 end: Individual warp thread.
on or dispersion, applied normally to warps
2.3 size: Gelatinous film-forming substance, in solu ti
but sometimes to wefts, generally before weaving.
2.4 locking thread: Independent thread used to lock the weft threads.
loom: Loom in which the weft is inserted by means other than a shuttle and is
2.5 shuttleless
drawn from a stationary supply.
odd warp threads pass over one
2.6 plain
...