SIST EN ISO 14945:2021
(Main)Small craft - Builder's plate (ISO 14945:2021)
Small craft - Builder's plate (ISO 14945:2021)
This document specifies requirements for the uniform display of the information exhibited on the
builder’s plate of small craft.
Personal watercraft are excluded from the Scope of this document.
Kleine Wasserfahrzeuge - Hersteller-Schild (ISO 14945:2021)
Dieses Dokument legt Anforderungen an die einheitliche Darstellung der Informationen auf dem Hersteller-Schild von kleinen Wasserfahrzeugen fest.
Wassersmotorräder sind vom Anwendungsbereich dieses Dokuments ausgeschlossen.
Petits navires - Plaque du constructeur (ISO 14945:2021)
Ce document spécifie les exigences relatives à l’affichage uniforme des informations figurant sur la plaque du constructeur de petits navires.
Les motos aquatiques sont exclues du domaine d'application de ce document.
Mala plovila - Oznaka proizvajalca (Zahteve za poenoten prikaz podatkov na proizvajalčevi plošči na malih plovilih) (ISO 14945:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14945:2021
01-september-2021
Nadomešča:
SIST EN ISO 14945:2004
SIST EN ISO 14945:2004/AC:2006
Mala plovila - Oznaka proizvajalca (Zahteve za poenoten prikaz podatkov na
proizvajalčevi plošči na malih plovilih) (ISO 14945:2021)
Small craft - Builder's plate (ISO 14945:2021)
Kleine Wasserfahrzeuge - Hersteller-Schild (ISO 14945:2021)
Petits navires - Plaque du constructeur (ISO 14945:2021)
Ta slovenski standard je istoveten z: EN ISO 14945:2021
ICS:
47.080 Čolni Small craft
SIST EN ISO 14945:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14945:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 14945:2021
EN ISO 14945
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 14945:2004
English Version
Small craft - Builder's plate (ISO 14945:2021)
Petits navires - Plaque du constructeur (ISO Kleine Wasserfahrzeuge - Hersteller-Schild (ISO
14945:2021) 14945:2021)
This European Standard was approved by CEN on 15 September 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14945:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14945:2021
EN ISO 14945:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14945:2021
EN ISO 14945:2021 (E)
European foreword
This document (EN ISO 14945:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by June 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14945:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 14945:2021 has been approved by CEN as EN ISO 14945:2021 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14945:2021
EN ISO 14945:2021 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I and Annex II of
Directive 2013/53/EU
Essential Requirements of Clause(s)/subclause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I.A.2.2 — Watercraft Builder’s Clauses 4.1, 4.5 and 5.1 For compliance with Annex I.A.2.2 (b),
Plate the builder’s plate shall include the CE
marking prescribed in Article 18 of
Directive 2013/53/EU.
The CE marking shall be followed by
the identification number of a notified
body where that body is involved in
the production control phase or in
Module PCA in accordance with Article
18(3) of Directive 2013/53/EU.
In the case of Module PCA referred to
in Article 19, Article 23 and Annex V
of Directive 2013/53/EU, the
Watercraft Builder’s Plate shall
display the contact details of the
notified body that carried out the
assessment and the wording
“post-construction assessment”.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 14945:2021
INTERNATIONAL ISO
STANDARD 14945
Second edition
2021-04
Small craft — Builder's plate
Petits navires — Plaque du constructeur
Reference number
ISO 14945:2021(E)
©
ISO 2021
---------------------- Page: 7 ----------------------
SIST EN ISO 14945:2021
ISO 14945:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14945:2021
ISO 14945:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
4.1 Material and fixing . 2
4.2 Marking . 2
4.3 Size of characters . 2
4.4 Size of pictograms and symbols . 2
4.5 Location . 3
5 Displayed builder’s plate information . 3
Annex A (informative) Design and examples of builder’s plates. 4
Bibliography .
...
SLOVENSKI STANDARD
oSIST prEN ISO 14945:2018
01-december-2018
0DODSORYLOD2]QDNDSURL]YDMDOFD =DKWHYH]DSRHQRWHQSULND]SRGDWNRYQD
SURL]YDMDOþHYLSORãþLQDPDOLKSORYLOLK ,62',6
Small craft - Builder's plate (ISO/DIS 14945:2018)
Kleine Wasserfahrzeuge - Hersteller-Schild (ISO/DIS 14945:2018)
Petits navires - Plaque du constructeur (ISO/DIS 14945:2018)
Ta slovenski standard je istoveten z: prEN ISO 14945
ICS:
47.080 ýROQL Small craft
oSIST prEN ISO 14945:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 14945:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 14945:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14945
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2018-10-17 2019-01-09
Small craft — Builder's plate
Petits navires — Plaque du constructeur
ICS: 47.080
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14945:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 14945:2018
ISO/DIS 14945:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 14945:2018
ISO/DIS 14945:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
4.1 Material and fixing . 2
4.2 Marking . 2
4.3 Size of characters . 2
4.4 Size of pictograms and symbols . 2
4.5 Location . 2
5 Displayed builder’s plate information . 3
Annex A (informative) Design and examples of builder’s plates. 4
Annex ANNEX ZA . 7
Bibliography . 8
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 14945:2018
ISO/DIS 14945:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 14945:2004), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Clarified terminology about what constitutes maximum load on a builder's plate to include all fluids
(addresses RSG PFE No. 286)
— Defined small craft
— Updated section 5 to provide guidance for inclusion of the mass of outboards above 3kW and
maximum HP and maximum recommended load for the builder’s plate
— Updated plate illustrations
— Added power symbol definition
— Added ZA Annex
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 14945:2018
ISO/DIS 14945:2018(E)
Introduction
The reason underlying the preparation of this International Standard is that the European Recreational
Craft Directive (Directives 94/25/EC followed by 2013/53/EU) requires that all recreational craft
within the scope of the directive shall be labelled with a craft builder’s plate containing specified
information. This requirement applies to craft built inside the European Union (EU) as well as craft
fr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.