SIST EN 60603-7-1:2011

SLOVENSKI STANDARD
01-september-2011
1DGRPHãþD
SIST EN 60603-7-1:2010
Konektorji za elektronsko opremo - 7-1. del: Podrobna specifikacije za 8-redne,
zaslonjene, proste in fiksne konektorje
Connectors for electronic equipment - Part 7-1: Detail specification for 8-way, shielded,
free and fixed connectors
Steckverbinder für elektronische Einrichtungen - Teil 7-1: Bauartspezifikation für
geschirmte freie und feste Steckverbinder, 8polig
Connecteurs pour équipements électroniques - Partie 7-1: Spécification particulière pour
les fiches et les embases blindées à 8 voies
Ta slovenski standard je istoveten z: EN 60603-7-1:2011
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60603-7-1
NORME EUROPÉENNE
June 2011
EUROPÄISCHE NORM
ICS 31.220.10 Supersedes EN 60603-7-1:2009

English version
Connectors for electronic equipment -
Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors
(IEC 60603-7-1:2011)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Partie 7-1: Spécification particulière pour Teil 7-1: Bauartspezifikation für
les fiches et les embases écrantées à 8 geschirmte freie und feste Steckverbinder,
voies 8polig
(CEI 60603-7-1:2011) (IEC 60603-7-1:2011)

This European Standard was approved by CENELEC on 2011-05-12. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60603-7-1:2011 E
Foreword
The text of document 48B/2163/CDV, future edition 3 of IEC 60603-7-1, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60603-7-1 on 2011-05-12.
This European Standard supersedes EN 60603-7-1:2009.
EN 60603-7-1:2009:
– the correction, or inclusion, of technical references;
– the harmonization of terminology with other parts of the EN 60603-7 series and other referenced
documents;
– the modification of screen dimensions so as to include connectors on the market;
– the inclusion of two new test groups (EP and FP) that provides the necessary cascading and
references to other parts of the EN 60603-7 series, and satisfies the requirements of ISO/IEC 11801
to enable correct referencing.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2012-02-12
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2014-05-12
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60603-7-1:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-1 NOTE  Harmonized as EN 60068-1.
IEC 60603-7-7 NOTE  Harmonized as EN 60603-7-7.
IEC 60603-7-71 NOTE  Harmonized as EN 60603-7-71.
__________
- 3 - EN 60603-7-1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60068-2-38 - Environmental testing - EN 60068-2-38 -
Part 2-38: Tests - Test Z/AD: Composite
temperature/humidity cyclic test

IEC 60512 Series Connectors for electronic equipment - Tests EN 60512 Series
and measurements
IEC 60512-1 - Connectors for electronic equipment - Tests EN 60512-1 -
and measurements -
Part 1: General
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications

IEC 60603-7 2008 Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors

IEC 60603-7 Series Connectors for electronic equipment EN 60603-7 Series

IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 -
low-voltage systems -
Part 1: Principles, requirements and tests

IEC 62153-4-12 - Metallic communication cable test methods - - -
Part 4-12: Electromagnetic compatibility
(EMC) - Coupling attenuation or screening
attenuation of connecting hardware -
Absorbing clamp method
ISO 1302 - Geometrical Product Specifications (GPS) - EN ISO 1302 -
Indication of surface texture in technical
product documentation
IEC 60603-7-1 ®
Edition 3.0 2011-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment –
Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors

Connecteurs pour équipements électroniques –
Partie 7-1: Spécification particulière pour les fiches et les embases écrantées à
8 voies
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX T
ICS 31.220.01 ISBN 978-2-88912-446-6

– 2 – 60603-7-1  IEC:2011
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 General . 7
1.1 Scope . 7
1.2 Normative references . 7
2 Terms and definitions . 7
3 Common features and isometric view . 8
3.1 Isometric view . 8
3.2 Mating information . 8
3.2.1 General . 8
3.2.2 Fixed connector . 9
3.2.3 Free connector . 10
4 Cable terminations and internal connections – Fixed and free connectors . 11
4.1 Internal connections . 11
4.2 Cable termination . 11
5 Gauges . 11
6 Characteristics . 11
6.1 General . 11
6.2 Pin and pair grouping assignment . 11
6.3 Classification into climatic category . 11
6.4 Electrical characteristics . 12
6.4.1 Creepage and clearance distances . 12
6.4.2 Voltage proof . 12
6.4.3 Current-carrying capacity. 12
6.4.4 Initial contact resistance – Interface only (separable fixed and free
contact) . 12
6.4.5 Input to output d.c. resistance . 12
6.4.6 Input to output d.c. resistance unbalance. 12
6.4.7 Initial insulation resistance . 13
6.4.8 Transfer impedance . 13
6.4.9 Coupling attenuation . 13
6.5 Mechanical . 13
6.5.1 Mechanical operation . 13
6.5.2 Insertion and withdrawal forces . 13
7 Tests and test schedule . 13
7.1 General . 13
7.2 Arrangement for contact resistance tests . 14
7.3 Arrangement for vibration tests. 14
7.4 Test procedures and measuring methods . 14
7.5 Preconditioning . 14
7.6 Wiring and mounting of specimens . 14
7.6.1 Wiring . 14
7.6.2 Mounting . 14
7.7 Test schedules . 14
7.7.1 Basic (minimum) test schedule . 14
7.7.2 Full test schedule . 14

60603-7-1  IEC:2011 – 3 –
Annex A (normative) Gauging continuity test. 21
Bibliography . 25

Figure 1 – Isometric view . 8
Figure 2 – Fixed connector details . 9
Figure 3 – Free connector view . 10
Figure A.1 – Gauge. 23
Figure A.2 – Gauge insertion . 24

Table 1 – Dimensions for Figure 2 . 10
Table 2 – Dimensions for Figure 3 . 11
Table 3 – Creepage and clearance distances . 12
Table 4 – Test group P . 15
Table 5 – Test group AP . 16
Table 6 – Test group BP . 17
Table 7 – Test group CP . 18
Table 8 – Test group DP . 19
Table 9 – Test group GP . 20
Table A.1 – Dimensions for Figure A.1 . 22

– 4 – 60603-7-1  IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –

Part 7-1: Detail specification for 8-way, shielded,
free and fixed connectors
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60603-7-1 has been prepared by subcommittee 48B: Connectors,
of IEC technical committee 48: Electromechanical components and mechanical structures for
electronic equipment.
This third edition cancels and replaces the second edition, published in 2009, and constitutes
a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
1) the correction, or inclusion, of technical references;
2) the harmonization of terminology with other parts of the IEC 60603-7 series and other
referenced documents;
3) the modification of screen dimensions so as to include connectors on the market;

60603-7-1  IEC:2011 – 5 –
4) the inclusion of two new test groups (EP and FP) that provides the necessary cascading
and references to other parts of the IEC 60603-7 series, and satisfies the requirements of
ISO/IEC 11801 to enable correct referencing.
The text of this standard is based on the following documents:
CDV Report on voting
48B/2163/CDV 48B/2209/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 60603 series, under the general title Connectors for electronic
equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
– 6 – 60603-7-1  IEC:2011
INTRODUCTION
Applications have emerged which require the use of the interface described in IEC 60603-7 with
certain performance specifications at higher frequencies. Therefore, a series of detail
specifications have been issued in the past few years in support of these new applications. In
order to improve readability and ease of maintenance, IEC subcommittee 48B (SC 48B)
decided to rearrange and restructure these existing documents.
This part of IEC 60603-7 contains only the necessary information regarding the shield of the
connector and is designed to be used as a base document for all shielded connectors in the
IEC 60603-7 series.
For further information regarding the IEC 60603-7 style connectors, reference is made to the
unshielded base document IEC 60603-7.
IEC 60603-7 is the base specification of the whole series. Subsequent specifications do not
duplicate information given in the base document, but list only additional requirements.
The following illustration shows the structure of the IEC 60603-7 series:
Unshielded Shielded
IEC 60603-7 IEC 60603-7-1
3 MHz
100 MHz
IEC 60603-7-2 IEC 60603-7-3
IEC 60603-7-4 IEC 60603-7-5
250 MHz
IEC 60603-7-41 IEC 60603-7-51
500 MHz
600 MHz
I
...