SIST EN 1459-3:2015
(Main)Rough-terrain trucks - Safety requirements and verification - Part 3: Additional requirements for variable reach trucks fitted with elevating work platform
Rough-terrain trucks - Safety requirements and verification - Part 3: Additional requirements for variable reach trucks fitted with elevating work platform
This European Standard specifies the additional safety requirements for trucks covered by
- EN 1459-1: Rough-terrain variable reach trucks
- EN 1459-2: Rough-terrain rotating trucks
- EN ISO 3691-2: Industrial variable reach trucks
when these trucks are equipped with elevating work platform.
This European Standard does not address hazards which may occur:
a) during manufacture;
b) when handling suspended work platforms which may swing freely;
c) when using trucks on public roads;
d) when operating in potentially explosive atmospheres;
e) when operating underground.
Geländegängige Stapler - Sicherheitsanforderungen und Verifizierung - Teil 3: Zusätzliche Anforderungen an Stapler mit veränderlicher Reichweite, ausgerüstet mit Arbeitsbühne
Diese Europäische Norm legt zusätzliche Sicherheitsanforderungen an die in den folgenden Normen erfassten Stapler fest, sofern diese Stapler mit einer Hubarbeitsbühne ausgerüstet sind:
- EN 1459 1: Geländegängige Stapler mit veränderlicher Reichweite;
- EN 1459 2: Geländegängige drehbare Stapler;
- EN ISO 3691 2: Motorkraftbetriebene Stapler mit veränderlicher Reichweite.
Diese Europäische Norm enthält keine Anforderungen hinsichtlich der Gefährdungen, die entstehen können:
- während der Herstellung;
- durch Befördern hängender Arbeitsbühnen, die frei pendeln können;
- durch Benutzung von Staplern auf öffentlichen Straßen;
- durch Benutzung in explosionsgefährdeten Umgebungen;
- durch Benutzung für Arbeiten unter Tage.
Chariots tout-terrain - Exigences de sécurité et vérification - Partie 3: Exigences supplémentaires pour chariots à portée variable équipés d’une plateforme élévatrice de travail
La présente Norme européenne spécifie les prescriptions de sécurité complémentaires relatives aux chariots couverts par les normes suivantes :
- EN 1459-1 : Chariots tout-terrain à portée variable
- EN 1459-2 : Chariots tout-terrain rotatifs
- EN ISO 3691-2 : Chariots automoteurs à portée variable
lorsque ces chariots sont équipés d’une plate-forme élévatrice de travail.
La présente Norme européenne ne traite pas des phénomènes dangereux pouvant apparaître :
a) pendant la fabrication ;
b) lors de la manutention de plates-formes de travail suspendues pouvant se balancer librement ;
c) lorsque les chariots sont utilisés sur des voies publiques ;
d) lors d’une utilisation en atmosphères explosibles ;
e) lors de travaux souterrains.
Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje - 3. del: Dodatne zahteve za vozila z mehanizmom za dviganje s spremenljivim dosegom z delovnimi ploščadmi
Ta evropski standard določa dodatne varnostne zahteve za viličarje, zajete v
– EN 1459-1: Terenski viličarji z ročico spremenljivega dosega
– EN 1459-2: Terenski vrtljivi viličarji
– EN ISO 3691-2: Industrijski viličarji z ročico spremenljivega dosega
ko so ti viličarji opremljeni z dvižno delovno ploščadjo.
Ta evropski standard ne obravnava nevarnosti, ki se lahko pojavijo:
a) med proizvodnjo;
b) pri upravljanju spuščenih delovnih ploščadi, ki lahko prosto nihajo;
c) pri uporabi viličarjev na javnih cestah;
d) pri upravljanju v potencialno eksplozivnih atmosferah;
e) pri upravljanju pod zemljo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.OMLYLPGeländegängige Stapler - Sicherheitsanforderungen und Verifizierung - Teil 3: Zusätzliche Anforderungen an Stapler mit veränderlicher Reichweite, ausgerüstet mit ArbeitsbühneChariots tout-terrain - Exigences de sécurité et vérification - Partie 3: Exigences supplémentaires pour chariots à portée variable équipés d’une plateforme élévatrice de travailRough-terrain trucks - Safety requirements and verification - Part 3: Additional requirements for variable reach trucks fitted with elevating work platform53.060Industrijski tovornjakiIndustrial trucksICS:Ta slovenski standard je istoveten z:EN 1459-3:2015SIST EN 1459-3:2015en,fr,de01-september-2015SIST EN 1459-3:2015SLOVENSKI
STANDARD
SIST EN 1459-3:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1459-3
May 2015 ICS 53.060 English Version
Rough-terrain trucks - Safety requirements and verification - Part 3: Interface between the variable-reach truck and the work platform
Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 3 : Interface entre le chariot à portée variable et la plateforme de travail
Geländegängige Stapler - Sicherheitsanforderungen und Verifizierung - Teil 3: Zusätzliche Anforderungen für Stapler mit veränderlicher Reichweite ausgerüstet mit ArbeitsbühneThis European Standard was approved by CEN on 16 April 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1459-3:2015 ESIST EN 1459-3:2015
EN 1459-3:2015 (E) 2 Contents Page
Foreword .3 Introduction .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .6 4 Safety requirements .6 4.1 General .6 4.2 Locking of the work platform .6 4.3 Dismounting of the work platform from the truck .6 4.4 Cables and connections .7 4.5 Mechanical locking device .7 4.6 Safety related functions .7 5 Verification .7 6 Information for use .8 6.1 General .8 6.2 Instruction handbook .8 6.2.1 General .8 6.2.2 Operating and maintenance instructions .8 6.3 Marking .9 Annex A (informative)
List of significant hazards . 10 A.1 General . 10 Bibliography . 11
SIST EN 1459-3:2015
EN 1459-3:2015 (E) 3 Foreword This document (EN 1459-3:2015) has been prepared by Technical Committee CEN/TC 150 “Industrial trucks - Safety”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2015, and conflicting national standards shall be withdrawn at the latest by November 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. The purpose of this standard is to give requirements for the specific aspects related to the fitting and interface of a work platform to a variable-reach truck designed for the lifting of persons. This standard does not give requirements for the complete truck fitted with a work platform. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. Trucks which are equipped with work platforms as interchangeable equipment are regarded as Mobile Elevating Work Platforms (MEWPs) as defined in 3.1 of EN 280:2013, and listed under Annex IV, item 17 of the Machinery Directive 2006/42/EC. EN 1459 consists of the following parts, under the general title Rough-terrain trucks — Safety requirements and verification: Part 1: Variable-reach trucks Part 2: Slewing variable-reach trucks Part 3: Interface between the variable-reach truck and the work platform Part 4: Additional requirements for variable reach trucks handling suspended loads Part 5: Additional requirements for attachments and attachment interface Part 6: Application of EN ISO 13849-1 to slewing and non-slewing variable-reach rough-terrain trucks (CEN/TR) Part 7: Test method and determination of noise emission According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1459-3:2015
EN 1459-3:2015 (E) 4 Introduction This document is a type-C standard as stated in EN ISO 12100. The machines concerned and the extent to which hazards, hazardous situations or hazardous events are covered as indicated in the Scope of this document. When requirements of this type-C standard are different from those which are stated in type-A or B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements of this type-C standard. Acknowledging that, at the time of publication, the requirements included in this European Standard do not represent the state of the art, a transition period of 18 mo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.