ISO 19732:2007
(Main)Equipment for crop protection - Sprayer filters - Colour coding for identification
Equipment for crop protection - Sprayer filters - Colour coding for identification
ISO 19732:2007 specifies the system of colour coding for identification of all types of filters used for the application of crop protection products in agriculture.
Matériel de protection des cultures — Filtres de pulvérisateur — Code de couleur pour l'identification
L'ISO 19732:2007 prescrit le code de couleur pour l'identification de tous les types de filtres utilisés en agriculture pour l'application de produits de protection des cultures.
General Information
- Status
- Published
- Publication Date
- 23-Apr-2007
- Technical Committee
- ISO/TC 23/SC 6 - Equipment for crop protection
- Drafting Committee
- ISO/TC 23/SC 6 - Equipment for crop protection
- Current Stage
- 9093 - International Standard confirmed
- Start Date
- 23-Aug-2021
- Completion Date
- 13-Dec-2025
Overview
ISO 19732:2007 is an international standard developed by the International Organization for Standardization (ISO) that defines a colour coding system for sprayer filters used in crop protection equipment. The standard ensures consistent identification of all types of filters applied in agricultural spraying of crop protection products, aiding in efficient maintenance, replacement, and operation safety.
This standard addresses the challenges related to filter identification by prescribing specific colours tied to the nominal mesh size of filters. This colour-coding system helps users quickly recognize filter types, reducing errors and improving process reliability in agricultural practice.
Key Topics
Scope and Purpose
ISO 19732:2007 applies to all filters used in equipment for applying crop protection products in agriculture. It standardizes colour coding for clear and uniform identification of filters.Definitions
- Nominal Mesh – the number of complete mesh openings per 25.4 mm length.
- Mesh Width – smallest distance between adjacent filter wires, expressed in millimeters.
- Wire Diameter – thickness of the filter wires, also expressed in millimeters.
Colour Coding System
The colour of each filter corresponds to its nominal mesh size. This facilitates rapid and foolproof identification on-site, supporting better operational decisions.Colour Specifications
The filters, including plastic materials, are uniformly dyed throughout the material to meet the colour coding requirements. The standard references RAL colour numbers for accuracy-an internationally recognized colour matching system.
Applications
ISO 19732:2007 plays a crucial role in agriculture, specifically within the crop protection sector, by standardizing filter identification in spraying equipment. Practical benefits include:
Efficient Maintenance and Replacement
Operators can easily identify the correct filter sizes needed for maintenance, minimizing downtime.Operational Safety
By eliminating confusion from incorrectly identified filters, the colour coding helps avoid misapplication of crop protection products.Supply Chain Consistency
Manufacturers and suppliers use the standardised colour codes to produce and distribute compatible sprayer filters with guaranteed identification.Training and Communication
The uniform system simplifies operator training and technical communication across international and multilingual settings.
Related Standards
ISO 19732:2007 is part of a suite of standards supporting agricultural machinery and crop protection equipment. Related standards include:
ISO/TC 23 Technical Committee - Works on tractors and agricultural machinery, including crop protection.
ISO 16119 Series - Focuses on spraying equipment specifications and testing.
ISO 4254 Series - Covers safety and performance of agricultural machinery, including sprayers.
These standards complement ISO 19732 by ensuring comprehensive coverage of crop protection equipment design, safety, and performance.
Keywords: ISO 19732, sprayer filters, crop protection equipment, colour coding, filter identification, agricultural spraying, mesh size filters, RAL colour code, agricultural standards, crop protection products, sprayer maintenance, filter mesh size.
ISO 19732:2007 - Equipment for crop protection -- Sprayer filters -- Colour coding for identification
ISO 19732:2007 - Matériel de protection des cultures -- Filtres de pulvérisateur -- Code de couleur pour l'identification
Frequently Asked Questions
ISO 19732:2007 is a standard published by the International Organization for Standardization (ISO). Its full title is "Equipment for crop protection - Sprayer filters - Colour coding for identification". This standard covers: ISO 19732:2007 specifies the system of colour coding for identification of all types of filters used for the application of crop protection products in agriculture.
ISO 19732:2007 specifies the system of colour coding for identification of all types of filters used for the application of crop protection products in agriculture.
ISO 19732:2007 is classified under the following ICS (International Classification for Standards) categories: 65.060.40 - Plant care equipment. The ICS classification helps identify the subject area and facilitates finding related standards.
You can purchase ISO 19732:2007 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 19732
First edition
2007-05-01
Equipment for crop protection — Sprayer
filters — Colour coding for identification
Matériel de protection des cultures — Filtres de pulvérisateur — Code
de couleur pour l'identification
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
Interna
...
NORME ISO
INTERNATIONALE 19732
Première édition
2007-05-01
Matériel de protection des cultures —
Filtres de pulvérisateur — Code de
couleur pour l'identification
Equipment for crop protection — Sprayer filters — Colour coding for
identification
Numéro de référence
©
ISO 2007
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2007
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2007 – Tous droits réservés
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...