ISO 6742-5:2015

INTERNATIONAL ISO
STANDARD 6742-5
First edition
2015-05-15
Cycles — Lighting and retro-
reflective devices —
Part 5:
Lighting systems not powered by the
cycle’s movement
Cycles — Dispositifs d’éclairage et dispositifs rétroréfléchissants —
Partie 5: Systèmes d’éclairage non alimentés par dynamo
Reference number
ISO 6742-5:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6742-5:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6742-5:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Lamps and interchangeable power source . 2
4.1 General . 2
4.2 Requirement . 2
5 Lamps and dedicated power source . 2
5.1 General . 2
5.2 Requirements . 2
6 Common requirements for lighting systems . 2
6.1 Corrosion resistance . 2
6.2 Water resistance . 2
6.3 Low battery indicator. 2
6.4 Power source . 2
7 Test method . 3
7.1 Lamps and interchangeable power source . 3
7.1.1 Lamps emitting light to the front . 3
7.1.2 Lamps emitting light to the rear . 3
7.2 Lamps and dedicated power source . 3
7.2.1 Lamps emitting light to the front . 3
7.2.2 Lamps emitting light to the rear . 3
7.3 Common test methods for lighting systems . 3
7.3.1 Corrosion testing . 3
7.3.2 Water resistance . . . 3
8 Instructions . 3
9 Marking . 4
9.1 Requirement . 4
9.2 Durability test . 4
9.2.1 Requirement . 4
9.2.2 Test method . 4
Bibliography . 5
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6742-5:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an
...