ISO 11193-1:2020

INTERNATIONAL ISO
STANDARD 11193-1
Third edition
2020-08
Single-use medical examination
gloves —
Part 1:
Specification for gloves made from
rubber latex or rubber solution
Gants en caoutchouc pour examen, non réutilisables —
Partie 1: Spécifications pour gants fabriqués à partir de latex de
caoutchouc ou d'une solution de caoutchouc
Reference number
©
ISO 2020
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
4.1 General . 2
4.2 Type . 2
4.3 Finish . 2
5 Materials . 2
6 Sampling and selection of test pieces . 3
6.1 Sampling . 3
6.2 Selection of test pieces . 3
7 Requirements . 3
7.1 Dimensions . 3
7.2 Water tightness . 5
7.3 Tensile properties . 5
7.3.1 General. 5
7.3.2 Force at break and elongation at break before accelerated ageing . 5
7.3.3 Force at break and elongation at break after accelerated ageing . 5
7.4 Sterility . 5
8 Packaging . 5
9 Marking . 6
9.1 General . 6
9.2 Unit package . 6
9.2.1 Sterile package . 6
9.2.2 Non-sterile package . . 6
9.3 Multi-unit package . 7
Annex A (normative) Test method for watertightness . 8
Bibliography .11
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses).
This third edition cancels and replaces the second edition (ISO 11193-1:2008), which has been
technically revised. It also partially incorporates the Amendment ISO 11193-1:2008/Amd: 2012.
The main changes compared to the previous edition are as follows:
— some general and editorial changes have been made in 4.1, 4.3, and Clause 5;
— the measurement of length has been corrected from the second finger to middle finger  in 7.1,
paragraph 2;
— the NOTE has been changed to main text in 7.3.3;
— the value has been corrected in Table 3;
— some general and editorial changes have been made to Annex A;
— the limit of powdered gloves has been included;
— Figures 1 and 2 of the previous edition have been replaced with Figure 1:
— updates have been made to the powdered surface and powder-free surface;
— the statement on aging gloves over six months old has been updated.
A list of all parts in the ISO 11193 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

INTERNATIONAL STANDARD ISO 11193-1:2020(E)
Single-use medical examination gloves —
Part 1:
Specification for gloves made from rubber latex or rubber
solution
WARNING — Persons using this document should be familiar with normal laboratory practices.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any regulatory conditions.
1 Scope
This document specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves
intended for use in medical examinations and diagnostic or therapeutic procedures to protect the
patient and the user from cross-contamination. It also covers rubber gloves intended for use in handling
contaminated medical materials and gloves with smooth surfaces or with textured surfaces over all or
part of the glove.
This document is intended as a reference for the performance and safety of rubber examination gloves.
It does not cover the safe and proper usage of examination gloves and sterilization procedures with
subsequent handling, packaging and storage procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
ISO 10993 (all parts),  — Biological evaluation of medical devices
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Classification
4.1 General
Gloves are classified by type and finish, as given in 4.2 and 4.3.
4.2 Type
a) Type 1: gloves made primarily from natural rubber latex.
b) Type 2: gloves mad
...