iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 6964:2019

(Main)

Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method

Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method

This document specifies test methods for the determination of the carbon black content of polyolefin compositions used in particular for the manufacture of pipes and fittings, and provides a basic specification for polyethylene pipes and fittings. This document applies equally to the material for manufacture and to any material taken from a pipe or fitting.

Tubes et raccords en polyoléfines — Détermination de la teneur en noir de carbone par calcination et pyrolyse — Méthode d'essai

Poliolefinske cevi in fitingi - Določanje vsebnosti saj s kalcinacijo in pirolizo - Preskusna metoda

General Information

Status
Published
Publication Date
26-Feb-2019
ICS
23.040.20 - Plastics pipes
Technical Committee
ISO/TC 138/SC 5 - General properties of pipes, fittings and valves of plastic materials and their accessories -- Test methods and basic specifications
Drafting Committee
ISO/TC 138/SC 5/WG 5 - Polyolefin pipes
Current Stage
9060 - Close of review
Start Date
02-Sep-2029
Ref Project
SIST ISO 6964:2021 - Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test method

Relations

Revises
ISO 6964:1986 - Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification
Effective Date
10-Nov-2012

Buy Standard

ISO 6964:2021ISO 6964:2021
PreviousNext
Standard
ISO 6964:2021
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
ISO 6964:2019 - Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test methodISO 6964:2019 - Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test method
PreviousNext
Standard
ISO 6964:2019 - Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test method
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 6964:2021
01-julij-2021
Nadomešča:
SIST ISO 6964:1996
Poliolefinske cevi in fitingi - Določanje vsebnosti saj s kalcinacijo in pirolizo -
Preskusna metoda
Polyolefin pipes and fittings -- Determination of carbon black content by calcination and
pyrolysis -- Test method
Tubes et raccords en polyoléfines -- Détermination de la teneur en noir de carbone par
calcination et pyrolyse -- Méthode d'essai
Ta slovenski standard je istoveten z: ISO 6964:2019
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST ISO 6964:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 6964:2021

---------------------- Page: 2 ----------------------
SIST ISO 6964:2021
INTERNATIONAL ISO
STANDARD 6964
Second edition
2019-02
Polyolefin pipes and fittings —
Determination of carbon black
content by calcination and pyrolysis —
Test method
Tubes et raccords en polyoléfines — Détermination de la teneur en
noir de carbone par calcination et pyrolyse — Méthode d'essai
Reference number
ISO 6964:2019(E)
©
ISO 2019

---------------------- Page: 3 ----------------------
SIST ISO 6964:2021
ISO 6964:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 6964:2021
ISO 6964:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Method A: Electrical tube furnace . 2
4.1 Reagents. 2
4.2 Apparatus . 2
4.3 Procedure . 2
4.3.1 Test conditions. 2
4.3.2 Sampling. 2
4.3.3 Conditioning . 2
4.3.4 Silica sample boat preparation for the test . 2
4.3.5 Test portion . 3
4.3.6 Determination . 3
4.4 Calculation and expression of results (Method A) .
...

INTERNATIONAL ISO
STANDARD 6964
Second edition
2019-02
Polyolefin pipes and fittings —
Determination of carbon black
content by calcination and pyrolysis —
Test method
Tubes et raccords en polyoléfines — Détermination de la teneur en
noir de carbone par calcination et pyrolyse — Méthode d'essai
Reference number
ISO 6964:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 6964:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6964:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Method A: Electrical tube furnace . 2
4.1 Reagents. 2
4.2 Apparatus . 2
4.3 Procedure . 2
4.3.1 Test conditions. 2
4.3.2 Sampling. 2
4.3.3 Conditioning . 2
4.3.4 Silica sample boat preparation for the test . 2
4.3.5 Test portion . 3
4.3.6 Determination . 3
4.4 Calculation and expression of results (Method A) . 3
5 Method B1 or B2: Muffle furnace (conventional B1) or (microwave B2) .4
5.1 Apparatus . 4
5.2 Procedure . 4
5.2.1 Test conditions. 4
5.2.2 Conditioning .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO/TS 22499:2024(Main)
Thermoplastic pipes for the conveyance of fluids — Inspection of polyethylene butt fusion joints using phased array ultrasonic testing

This document describes the phased array ultrasonic testing (PAUT) of polyethylene butt fusion (BF) joints, including pipe-to-pipe, pipe-to-fitting and fitting-to-fitting joints, used for the conveyance of fluids. This document provides a test, whereby the presence of imperfections such as voids, inclusions, lack of fusions, misalignment and particulate contamination in the BF joints can be detected. The document is only applicable to polyethylene pipes and fittings without a barrier to ultrasonic waves. This document also provides requirements for procedure qualification and guidance for personnel qualifications, which are essential for the application of this test technique. This document also covers the equipment, the preparation and performance of the test, the indication assessment and the reporting for polyethylene BF joints. Acceptance criteria are not covered in this document.

  • Technical specification
    20 pages
    English language
    sale 15% off
ISO
ISO/TS 16943:2023(Main)
Thermoplastic pipes for the conveyance of fluids — Inspection of polyethylene electrofusion socket joints using phased array ultrasonic testing

This document describes phased array ultrasonic testing (PAUT) of polyethylene electrofusion (EF) socket joints used for the conveyance of fluids. This document provides a test whereby the presence of imperfections such as voids, wire dislocation, misalignment, pipe under-penetration, particulate contamination and lack of fusion in electrofusion socket joints can be detected. The technique is only applicable to polyethylene electrofusion socket fittings without a barrier to ultrasonic waves. This document also provides requirements for procedure qualification and guidance for personnel qualifications, which are essential for the application of this test technique. This document covers the test equipment, the preparation and performance of the test, the assessment of indications and the reporting for polyethylene EF joints. Acceptance criteria are not covered in this document. NOTE 1 At the time of publication, experience only exists in the use of PAUT for polyethylene (PE80 and PE100) electrofusion socket joint sizes between 90 mm and 710 mm (SDR 11 and 17).[1][2][3][4][5][6][7] NOTE 2 Interlaboratory testing has shown that PAUT is a viable method for enhancing the integrity assessment of electrofusion joints.[8][15][16] NOTE 3 This document does not apply to the detection of unscraped pipe. Such detection can be achieved by simple visual testing, provided mechanical scraping tools are employed. NOTE 4 PAUT techniques for cold fusion detection are known to be available. However further research verification and experience are needed to transfer the technique into an ISO International Standard. This document does not provide any information regarding the detection of cold fusions.

  • Technical specification
    25 pages
    English language
    sale 15% off
ISO
ISO 2505:2023(Main)
Thermoplastics pipes — Longitudinal reversion — Test method and parameters

This document specifies a method for determining the longitudinal reversion of thermoplastics pipes, to be carried out in either a liquid or in air. In case of dispute, heated liquid is used as the reference. This document is applicable to all thermoplastics pipes with smooth internal and external walls of constant cross‑section. It is not applicable to non‑smooth structured‑wall thermoplastics pipes. The parameters appropriate to the pipe material and recommendations for the maximum levels of reversion as a function of the pipe material are given in Annex A. This method is applicable for pipes of wall thickness ≤ 16 mm.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 9854-2:2023(Main)
Thermoplastics pipes for the transport of fluids — Determination of Charpy impact properties — Part 2: Test conditions for pipes of various materials

This document specifies the values or options chosen for the test parameters (i.e. the impact energy, specimen dimensions, specimen type, specimen supports and test temperature) for both unnotched and notched specimens, for testing the impact resistance (pendulum method) of thermoplastics pipes of the following materials, in accordance with ISO 9854-1. It applies to pipes made of unplasticized poly(vinyl chloride) (PVC-U), high-impact poly(vinyl chloride) (PVC-HI), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile/butadiene/styrene (ABS), acrylonitrile/styrene/acrylate (ASA), propylene homopolymer (PP-H), propylene impact polymer (PP-B), propylene random copolymer (PP-R), propylene random copolymer with modified crystallinity (PP-RCT), and polyethylene (PE).

  • Standard
    5 pages
    English language
    sale 15% off
ISO
ISO 9854-1:2023(Main)
Thermoplastics pipes for the transport of fluids — Determination of Charpy impact properties — Part 1: General test method

This document specifies two general test methods, Method A and Method B, to be used for the determination of the impact properties of unnotched and notched specimens cut from thermoplastics pipes for the transport of fluids. — Method A: unnotched method, for unnotched specimens cut from thermoplastics pipes for the transport of fluids. — Method B: notched method, for specimens cut from thermoplastics pipes for the transport of fluids, into which a notch has been machined. The use of Method A or Method B is determined by the relevant product standards. This document is not intended as a reference test method for the determination of the impact strength of pipes. ISO 3127, relating to the determination of the impact strength of pipes by means of a falling mass, is the reference test method. However, this document can be used for scientific research, materials testing or the examination of pipe when it is not possible to take measurements in accordance with the reference method. This document can be applied to either isolated batches or continuous production of pipe.

  • Standard
    12 pages
    English language
    sale 15% off
ISO
ISO 13479:2022(Main)
Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes

This document specifies a test method for determining the resistance to slow crack growth of polyolefin pipes, expressed in terms of time to failure in a hydrostatic pressure test on a pipe with machined longitudinal notches in the outside surface. The test is applicable to pipes of wall thickness greater than 5 mm.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    French language
    sale 15% off
ISO
ISO 13844:2022(Main)
Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with plastic pipes — Test method for leaktightness under negative pressure, angular deflection and deformation

This document specifies a method for testing the leak tightness under negative pressure, angular deflection and deformation of assembled joints between elastomeric-sealing-ring-type sockets made of plastic or metal and plastic pressure pipes.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 6259-2:2020(Main)
Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI)

This document specifies a method for determining the tensile properties of pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI, PVC-M or PVC-A), and in particular the following properties: — the stress at yield and stress at break; — the elongation at break. NOTE The general method of test for the determination of the tensile properties of thermoplastics pipes is given in ISO 6259‑1. This document also gives, for information purposes only, the corresponding basic specifications in Annexes A, B, C and D.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off
ISO
ISO 10146:2019(Main)
Crosslinked polyethylene (PE-X) and crosslinked medium density polyethylene (PE-MDX) — Effect of time and temperature on expected strength

This document specifies the minimum values for expected strength as a function of time and temperature in the form of reference lines, for use in calculations on crosslinked polyethylene (PE-X) pipes and crosslinked medium density polyethylene (PE-MDX) pipes. NOTE 1 This document is applicable for pipes with the minimum level of crosslinking after production in accordance with Clause 4. NOTE 2 The density range for medium density polyethylene is 926 kg/m3 to 940 kg/m3 in accordance with ISO 17855-1:2014[2].

  • Standard
    11 pages
    English language
    sale 15% off
ISO
ISO 13761:2017(Main)
Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C

ISO 13761:2017 specifies a method for the derivation of pressure reduction factors to obtain the allowable operating pressure for operation of polyethylene (PE) pipeline systems at temperatures between 20 °C and 40 °C or 50 °C, dependent on the classification of the material used for manufacture.

  • Standard
    4 pages
    English language
    sale 15% off