ISO 18758-2:2018
(Main)Mining and earth-moving machinery — Rock drill rigs and rock reinforcement rigs — Part 2: Safety requirements
Mining and earth-moving machinery — Rock drill rigs and rock reinforcement rigs — Part 2: Safety requirements
This document specifies the safety requirements for rock drill rigs and rock reinforcement rigs designed for the following underground or surface operations: a) blast hole drilling; b) rock reinforcement; c) drilling for secondary breaking; d) dimensional stone drilling; e) mineral prospecting, e.g. utilizing core drilling or reverse circulation; f) water and methane drainage drilling; g) raise boring. NOTE Rigs can be designed for more than one of the operations above. See ISO 18758-1 for vocabulary. This document is also applicable to earth-moving machinery as defined in ISO 6165, modified to become a rock drill rig or rock reinforcement rig. This document is not applicable to the following machines: drill rigs for soil and rock mixture; (geothermal drill rigs, water well drill rigs, water jet drill rigs, micro pile drill rigs; surface horizontal directional drill rigs (HDD) as defined in ISO 21467), kelly drill rigs (and casing drivers); cable tool drill rigs; pre-armouring machines; sonic drill rigs; shaft sinking drill rigs; crane attached drill rigs; drill rigs on derricks; scaling machines. This document deals with the significant hazards, hazardous situations or hazardous events, as listed in Annex E, relevant to rock drill rigs and rock reinforcement rigs (see ISO 18758‑1), when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer. This document is not applicable to rigs manufactured before the date of its publication.
Engins d'exploitation minière et de terrassement — Appareils de forage et de renfort de roches — Partie 2: Exigences de sécurité
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 18758-2
First edition
2018-06
Mining and earth-moving
machinery — Rock drill rigs and rock
reinforcement rigs —
Part 2:
Safety requirements
Engins d'exploitation minière et de terrassement — Appareils de
forage et de renfort de roches —
Partie 2: Exigences de sécurité
Reference number
©
ISO 2018
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 4
4 Safety requirements . 4
4.1 General requirements . 4
4.1.1 General. 4
4.1.2 Ergonomics . 5
4.1.3 Hot and cold surfaces and sharp edges . 5
4.1.4 Hoses, pipes and fittings under pressure . 5
4.1.5 Handling of the rig and its parts . 5
4.1.6 Access to operating positions and servicing points . 5
4.1.7 Isolation of external electrical energy sources . 6
4.1.8 Prevention of unexpected start-up . 6
4.2 Driving, tramming and operating position . 6
4.2.1 General. 6
4.2.2 Operator's position . 6
4.2.3 Visibility. 9
4.2.4 Operator protective structures . 9
4.3 Controls, functions and systems .10
4.3.1 General.10
4.3.2 Starting .10
4.3.3 Stopping – Normal stopping .10
4.3.4 Failure of the power supply .10
4.4 Control devices .10
4.4.1 General.10
4.4.2 Control system of remote controlled and automated rigs .11
4.4.3 Emergency stop and safety devices .11
4.4.4 Operating instrumentation .12
4.5 Stability .12
4.6 Steering .12
4.7 Carrier brakes .12
4.7.1 General.12
4.7.2 General requirements for wheel-mounted rigs .12
4.7.3 Service braking system for wheel-mounted rigs.13
4.7.4 Secondary braking system for wheel-mounted rigs .13
4.7.5 Parking braking system for wheel-mounted rigs .13
4.7.6 Braking systems for crawler-mounted rigs .13
4.7.7 Braking systems for "skid steer" wheel-mounted rigs .13
4.8 Tyres and rims .13
4.9 Protection against moving parts .14
4.9.1 General.14
4.9.2 Moving parts involved in the working process .14
4.10 Electrical installations .15
4.10.1 Electric power installation .15
4.10.2 Electromagnetic compatibility (EMC) .15
4.10.3 Battery installation .16
4.11 Machines powered by diesel engine .16
4.12 Fuel systems .16
4.12.1 Fuel tanks .16
4.12.2 Fuel tank filler inlet .17
4.12.3 Fuel tank vent system .17
4.13 Hydraulic system .17
4.13.1 General.17
4.13.2 Load holding cylinders .17
4.14 Pneumatic installations .17
4.15 Lighting .18
4.15.1 Working light .18
4.15.2 Illumination when tramming .18
4.15.3 Internal operator cab or operator canopy lighting and access lighting .18
4.16 Fire protection .18
4.16.1 General.18
4.16.2 Operator cab interior upholstery .18
4.16.3 Portable fire extinguishers .19
4.16.4 Fire suppression systems .19
4.16.5 Engine shutdown .19
4.16.6 Single conductor cables .19
4.16.7 Monitoring device .19
4.17 Noise and vibration .19
4.17.1 General.19
4.17.2 Noise .20
4.17.3 Vibration .20
4.18 Dust suppression.20
4.19 Winches and ropes .20
4.19.1 Winches, ropes and sheaves for lifting and feed .20
4.19.2 Winches for operating
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.