IEC 60151-8:1966
(Main)Measurements of the electrical properties of electronic tubes and valves - Part 8: Measurement of cathode heating time and heater warm-up time
Measurements of the electrical properties of electronic tubes and valves - Part 8: Measurement of cathode heating time and heater warm-up time
The contents of the corrigendum of July 1967 have been included in this copy.
Mesures des caractéristiques électriques des tubes électroniques - Partie 8: Mesure des temps de chauffage de la cathode et du filament
Le contenu du corrigendum de juillet 1967 a été pris en considération dans cet exemplaire.
General Information
Buy Standard
Standards Content (Sample)
IEC Publication 151-8 (1966)
Publication 151-8 de la CE! (1966)
CORRIGENDUM 1
CORRECTIF 1
Page 11, figure 4 Page 11, Figure 4
Page 12, figure 5:
...
This May Also Interest You
Applicable to cathode ray tubes and cathode ray tube assemblies which are intended for use as components in apparatus and which have integral protection with respect to the effects of implosion. A CRT covered by this standard is intended to be installed in an enclosure designed both to protect the rear of the CRT against mechanical or other damage under normal conditions of operation and to protect the user against particles expelled in a backwards direction from the CRT face in the event of implosion.
- Standard58 pagesEnglish languagesale 15% off
IEC 60139:2000 gives guidance on the preparation of outline drawings of cathode-ray tubes (CRTs), tube components, tube sub-assemblies and ancillary components with the object of encouraging the same practice when publications are prepared in different countries. These recommendations are contained in the specimen drawings, descriptive text and in the tables of required dimensions.
- Standard30 pagesEnglish languagesale 15% off
- Standard60 pagesEnglish and French languagesale 15% off
- Standard3 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish and French languagesale 15% off
IEC 60860:2014 prescribes general, radiation detection, environmental, mechanical, electromagnetic and documentation requirements and specifies acceptance criteria for criticality accident warning equipment. This International Standard applies to equipment intended to provide warning of a criticality accident by the detection of gamma radiation, neutrons or both from such an event. The main technical changes with regard to the previous edition are as follows:
- reference to IEC 61508 concerning the safety classification;
- introducing requirement for the alarm sound level;
- energy response requirement changes;
- specification of time period of 1 min for the overload requirement;
- updated EMC, mechanical and environmental requirements according to IEC 62706.
- Standard34 pagesEnglish and French languagesale 15% off
CISPR 16-1-2:2014 is available as CISPR 16-1-2:2014 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
CISPR 16-1-2:2014 specifies the characteristics and performance of equipment for the measurement of radio disturbance voltages and currents in the frequency range 9 kHz to 1 GHz. It has the status of a basic EMC publication. Specifications for ancillary apparatus are included for artificial mains networks, current and voltage probes and coupling units for current injection on cables. It is intended that the requirements of this publication are fulfilled at all frequencies and for all levels of radio disturbance voltages and currents within the CISPR indicating range of the measuring equipment. Methods of measurement are covered in the CISPR 16-2 series, and further information on radio disturbance is given in CISPR 16-3, while uncertainties, statistics and limit modelling are covered in the CISPR 16-4 series. This second edition cancels and replaces the first edition published in 2003 and its Amendment 1 (2004) and Amendment 2 (2006). This edition constitutes a technical revision which includes the following significant technical changes with respect to the previous edition:
- requirements from CISPR 22 for the AAN have been copied to this standard;
- and the CDNE for measurement of disturbance voltage in the frequency range 30 MHz to 300 MHz is added.
- Standard277 pagesEnglish languagesale 15% off
- Standard183 pagesEnglish and French languagesale 15% off
- Standard391 pagesEnglish and French languagesale 15% off
IEC 61643-312:2013 is applicable to gas discharge tubes (GDT) used for overvoltage protection in telecommunications, signalling and low-voltage power distribution networks with nominal system voltages up to 1 000 V (r.m.s.) a.c. and 1 500 V d.c. They are defined as a gap, or several gaps with two or three metal electrodes hermetically sealed so that gas mixture and pressure are under control. They are designed to protect apparatus or personnel, or both, from high transient voltages. This standard provides information about the characteristics and circuit applications of GDTs having two or three electrodes. This standard does not specify requirements applicable to complete surge protective devices, nor does it specify total requirements for GDTs employed within electronic devices, where precise coordination between GDT performance and surge protective device withstand capability is highly critical. Keywords: gas discharge tubes (GDT), overvoltage protection in telecommunications, signalling and low-voltage power distribution networks, nominal system voltages up to 1 000 V (r.m.s.) a.c. and 1 500 V d.c. The contents of the corrigendum of July 2013 have been included in this copy.
- Standard43 pagesEnglish and French languagesale 15% off
IEC 61643-311:2013 is applicable to gas discharge tubes (GDT) used for overvoltage protection in telecommunications, signalling and low-voltage power distribution networks with nominal system voltages up to 1 000 V (r.m.s.) a.c. and 1 500 V d.c..They are defined as a gap, or several gaps with two or three metal electrodes hermetically sealed so that gas mixture and pressure are under control. They are designed to protect apparatus or personnel, or both, from high transient voltages. This standard contains a series of test criteria, test methods and test circuits for determining the electrical characteristics of GDTs having two or three electrodes. This standard does not specify requirements applicable to complete surge protective devices, nor does it specify total requirements for GDTs employed within electronic devices, where precise coordination between GDT performance and surge protective device withstand capability is highly critical. This second edition of IEC 61643-311 cancels and replaces the first edition published in 2001. It constitutes a technical revision. Specific changes with respect to the previous edition are: Addition of performance values. Key words: gas discharge tubes (GDT), overvoltage protection in telecommunications, signalling and low-voltage power distribution networks, nominal system voltages up to 1 000 V (r.m.s.) a.c. and 1 500 V d.c.
- Standard53 pagesEnglish and French languagesale 15% off
IEC 60601-2-65:2012 applies to the basic safety and essential performance of dental intra-oral X-ray equipment and its main components. The scope of this standard is restricted to X-ray equipment where the X-ray tube assembly contains the high-voltage transformer assembly. Dental extra-oral X-ray equipment is excluded from the scope of this standard. This particular standard has been prepared to provide, based on IEC 60601-1:2005 and its collaterals, a complete set of basic safety and essential performance requirements for dental intra-oral X-ray equipment. While the previously existing standards for such equipment were dedicated to components and subsystems, this particular standard addresses the system level of dental intra-oral X-ray equipment. Components and their functions are addressed as far as necessary.
- Standard92 pagesEnglish languagesale 15% off
- Standard87 pagesEnglish and French languagesale 15% off
- Standard194 pagesEnglish and French languagesale 15% off
- Standard184 pagesEnglish and French languagesale 15% off
The contents of the corrigendum of May 2016 have been included in this copy.
- Standard107 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.