EN 61029-2-11:2003

SLOVENSKI SIST EN 61029-2-11:2004

STANDARD
marec 2004
Varnost premičnih električnih orodij - 2-11. del: Posebne zahteve za
kombinirane krožne žage z delovno mizo in za zajeralne žage (IEC 61029-2-
11:2001; spremenjen)
Safety of transportable motor-operated electric tools - Part 2-11: Particular
requirements for combined mitre and bench saws
ICS 25.080.60; 25.140.20 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 61029-2-11
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2003

ICS 25.080.60; 25.140.20
English version
Safety of transportable motor-operated electric tools
Part 2-11: Particular requirements for combined mitre and bench saws
(IEC 61029-2-11:2001, modified)

Sécurité des machines-outils électriques Sicherheit transportabler
semi-fixes motorbetriebener Elektrowerkzeuge
Partie 2-11: Règles particulières pour les Teil 2-11: Besondere Anforderungen für
scies d'établi-scies à mortaiser kombinierte Tisch- und Gehrungssägen
(CEI 61029-2-11:2001, modifiée) (IEC 61029-2-11:2001, modifiziert)

This European Standard was approved by CENELEC on 2002-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61029-2-11:2003 E
Foreword
The text of the International Standard IEC 61029-2-11:2001, prepared by SC 61F, Safety of hand-
held motor-operated electric tools, of IEC TC 61, Safety of household and similar electrical
appliances, together with the common modifications prepared by the Technical Committee
CENELEC TC 61F, Hand-held and transportable electric motor-operated tools, was submitted to the
Unique Acceptance Procedure and was approved by CENELEC as EN 61029-2-11 on 2002-10-01.

The following dates were fixed:

- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-04-01

- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-10-01

In this document the common modifications to the International Standard are indicated by a vertical
line in the left margin of the text.

This European Standard is divided into two parts:

Part 1 General requirements, which are common to most transportable motor, operated
tools (for the purpose of this standard referred to simple as tools) which could
come within the scope of this standard.

Part 2 Requirements for particular types of tool which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and
characteristics of these specific tools.

This European Standard has been prepared under a mandate given to CEN/CENELEC by the
European Commission and European Free Trade Association and supports the essential health
and safety requirements of the Machinery Directive.
of the
Compliance with the relevant clauses of Part 1 together with a relevant Part 2 of this standard
provides one means of confirming with the specified essential requirements of the Directive. The
requirements defined in EN 1050 are also dealt with in this standard.

For noise and vibration this standard covers the requirements for their measurement, the
provisions of information arising from these measurements and the provision of information about
the Personal Protective Equipment required. Specific requirements for the reduction of the risk
arising from noise and vibration through the design of the tool are not given as this reflects the
current state of art.
Warning: Other requirements arising from other European Directives can be applicable to
the products falling within the scope of this standard.

- 3 - EN 61029-2-11:2003
CEN have prepared standards for industrial machines, which may extend transportable machines.
Although CEN and CENELEC have where appropriate used common solutions to provide uniform
levels of protection, person using this standard should check the scope of both this and CEN
standards to ensure that a correct standard is used.

EN 61029-2-11 is to be used in conjunction with EN 61029-1:2000.
EN 61029-2-11 supplements or modifies the corresponding clauses of EN 61029-1, so as to
convert it into the European Standard: Safety requirements for transportable combined mitre and
bench saws.
Where a particular subclause is not mentioned in this Part 2-11, that subclause applies as far as
reasonable. Where this Part 2-11 states "addition" "modification" or "replacement", the relevant text
of Part 1 is to be adapted accordingly.

Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from
101.
Subclauses, tables and figures which are additional to those in IEC 61029-2-11 are prefixed "Z".

NOTE In this standard the following print types are used:
Requirements proper,
-
Test specifications,
-
- Explanation matter.
Contents
1 Scope.6
2 Definitions.6
3 General requirements.7
4 General notes on test.7
5 Rating.7
6 Classification.7
7 Marking and information for use.7
8 Protection against electric shock.10
9 Starting.10
10 Input and current.10
11 Heating.11
12 Leakage current.11
13 Environmental requirements.11
14 Progress against ingress of foreign bodies and moisture resistance.12
15 Insulation resistance and electrical strength.12
16 Endurance.12
17 Abnormal operation.12
18 Stability and mechanical hazards .13
19 Mechanical strength.21
20 Construction.22
21 Internal wiring.23
22 Components.23
23 Supply connection and external flexible cables and cords.23
24 Terminals for external conductors .23
25 Provision for earthing.23
26 Screws and connections.23
27 Creepage distances, clearances and distances through insulation .24
28 Resistance to heat, fire and tracking .24
29 Resistance to rusting.24
30 Radiation.24

Figure Z101 – Combined mitre and bench saw (type A).25
Figure Z102 – Combined mitre and bench saw (type B).26
Figure Z103 – Orientation of tool and operator.27
Figure Z104 – Saw blade areas – Combined mitre and bench saw in mitre saw position (type B)28
Figure Z105 – Self-closing guard – Opening angle .29
Figure Z106 – Open guard construction.30
Figure Z107 – Dimensions test probe.31

- 5 - EN 61029-2-11:2003
Figure Z108 – Riving knife mounted guard.31
Figure Z109 – Top guard side walls .32
Figure Z110a – Riving knife mounted saw blade guard – Stability test without saw blade.33
Figure Z110b – Saw blade guard mounted separately from the riving knife – Stability test .34
Figure Z111 – Guarding below the bench table – Type B machine .35
Figure Z112 – Width of the slot in the table.36
Figure Z113 – Dimensions of the bench saw table.36
Figure Z114 – Riving knife adjustment .37
Figure Z115 – Riving knife testing / strength of riving knife mounting.38
Figure Z116 – Riving knife testing / strength of riving knife .39
Figure Z117 – Two position rip fence .40
Figure Z118 – Flange characteristics .41
Figure Z119 – Example of push block and push stick .42

Table Z101 – Conditions for dust measurement.11
Table Z102 – Noise test conditions for combined mitre and bench saws .12
Table Z103 – Minimum dimensions of the saw table.17

Annex A (normative) Normative references.43

1 Scope
This clause of Part 1 is applicable except as follows:

1.1 Addition:
This standard applies to transportable combined mitre and bench saws with a saw blade diameter
not exceeding 315 mm and intended for cutting wood and analogue materials.

1.2 Addition:
This standard does not apply to transportable mitre and bench saws used to cut steel, iron, brass
or food.
Single function bench saws are covered by EN 61029-2-1.

Single function mitre saws are covered by EN 61029-2-9.

Combined mitre and bench saws other than transportable are covered by EN 1870-3.

2 Definitions
This clause of Part 1 is applicable except as follows:

2.2.21 Replacement:
2.21
normal load
the load to obtain rated input

2.101
combined mitre and bench saw
a saw that can be used:
a) as a down-cutting cross cut saw;
b) as a circular bench saw.
The saw may be of type A or type B as defined in 2.2.Z103 and 2.2.Z104

2.Z101
transportable combined mitre and bench saw
a mitre and bench saw designed to be used on a bench or a table similar to a bench and which is
intended to carry out work in a stationary position and is transportable by hand by one person

- 7 - EN 61029-2-11:2003
2.Z102
type A saw
a combined mitre and bench saw equipped with tw
...