EN 60384-17:2005

STANDARDNespremenljivi kondenzatorji za uporabo v elektronski opremi – 17. del: Področna specifikacija: nespremenljivi kondenzatorji z dielektrikom iz metalizirane polipropilenske folije za izmenične napetosti in impulzni kondenzatorji (IEC 60384-17:2005)Fixed capacitors for use in electronic equipment – Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors (IEC 60384-17:2005)©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 60384-17:2006(en)ICS31.060.10

EUROPEAN STANDARD
EN 60384-17 NORME EUROPÉENNE EUROPÄISCHE NORM
December 2005 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-17:2005 E
ICS 31.060.30
English version
Fixed capacitors for use in electronic equipment Part 17: Sectional specification:
Fixed metallized polypropylene film dielectric a.c. and pulse capacitors (IEC 60384-17:2005)
Condensateurs fixes utilisés
dans les équipements électroniques Partie 17: Spécification intermédiaire: Condensateurs fixes pour tension alternative et pour impulsions à diélectrique en film de polypropylène métallisé (CEI 60384-17:2005)
Festkondensatoren zur Verwendung in Geräten der Elektronik Teil 17: Rahmenspezifikation: Festkondensatoren mit metallisierter Polypropylen-Folie als Dielektrikum für Wechselspannungs- und Impulsbetrieb (IEC 60384-17:2005)
This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

at national level by publication of an identical
national standard or by endorsement
(dop)
2006-08-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2008-11-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 60384-17:2005 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60065 NOTE Harmonized as EN 60065:2002 (modified).
IEC 60384-14 NOTE Harmonized as EN 60384-14:2005 (not modified). __________

- 3 - EN 60384-17:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60063 1963 Preferred number series for resistors and capacitors - - A1 1967
- - A2 1977
- - IEC 60068-1 - 1) Environmental testing Part 1: General and guidance
EN 60068-1 1994 2) IEC 60384-1 (mod) - 1) Fixed capacitors for use in electronic equipment Part 1: Generic specification
EN 60384-1 + corr. October 2001 2) 2001 IEC 60384-17-1 - 1) Part 17-1: Blank detail specification - Fixed metallized polypropylene film dielectric a.c. and pulse capacitors - Assessment levels E and EZ
EN 60384-17-1 2005 2) IEC 60410 - 1) Sampling plans and procedures for inspection by attributes
- - ISO 3 - 1) Preferred numbers - Series of preferred numbers
- -
1) Undated reference. 2) Valid edition at date of issue.

INTERNATIONAL STANDARD IEC60384-17 QC 301300Second edition2005-11 Fixed capacitors for use in electronic equipment –Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors
 IEC 2005

Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch V For price, see current cataloguePRICE CODE
Commission Electrotechnique InternationaleInternational Electrotechnical Commission

– 2 – 60384-17  IEC:2005(E) CONTENTS
FOREWORD.4
1 General.7 1.1 Scope.7 1.2 Object.7 1.3 Normative references.7 1.4 Information to be given in a detail specification.8 1.5 Terms and definitions.9 1.6 Marking.10 2 Preferred ratings and characteristics.11 2.1 Preferred characteristics.11 2.2 Preferred values of ratings.11 3 Quality assessment procedures.12 3.1 Primary stage of manufacture.12 3.2 Structurally similar components.12 3.3 Certified records of released lots.13 3.4 Qualification approval.13 3.5 Quality conformance inspection.20 4 Test and measurement procedures.22 4.1 Visual examination and check of dimensions.22 4.2 Electrical tests.22 4.3 Robustness of terminations.25 4.4 Resistance to soldering heat.25 4.5 Solderability.25 4.6 Rapid change of temperature.25 4.7 Vibration.25 4.8 Bump.26 4.9 Shock.26 4.10 Climatic sequence.27 4.11 Damp heat, steady state.28 4.12 Endurance.28 4.13 Charge and discharge.30 4.14 Component solvent resistance.30 4.15 Solvent resistance of the marking.30
Bibliography.31
Table 1 – Preferred values.10 Table 2 – Preferred combinations.12 Table 3 – Sampling plan together with numbers of permissible defectives for qualification approval tests for a.c. and pulse capacitors.14 Table 4 – Test schedule for qualification approval.15 Table 5 – Lot-by-lot inspection.21

60384-17  IEC:2005(E) – 3 – Table 6 – Periodic inspection.21 Table 7 – Tangent of loss angle.23 Table 8 – Insulation resistance requirements.23 Table 9 – Correction factors.24 Table 10 – Characteristics at lower category temperature.24 Table 11 – Characteristics at upper category temperature.24 Table 12 – Preferred severities.26

– 4 – 60384-17  IEC:2005(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-17
...