EN 60317-0-9:2015

SLOVENSKI STANDARD
01-marec-2016
Specifikacije za posebne vrste navijalnih žic - 0-9. del: Splošne zahteve -
Emajlirana pravokotna aluminijeva žica
Specifications for particular types of winding wires - Part 0-9: General requirements -
Enamelled rectangular aluminium wire
Ta slovenski standard je istoveten z: EN 60317-0-9:2015
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60317-0-9

NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2015
ICS 29.060.10
English Version
Specifications for particular types of winding wires - Part 0-9:
General requirements - Enamelled rectangular aluminium wire
(IEC 60317-0-9:2015)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-9: Exigences générales - Fil de section Wickeldrähten - Teil 0-9: Allgemeine Anforderungen -
rectangulaire émaillé en aluminium Flachdrähte aus Aluminium, lackisoliert
(IEC 60317-0-9:2015) (IEC 60317-0-9:2015)
This European Standard was approved by CENELEC on 2015-06-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-0-9:2015 E
European foreword
The text of document 55/1519/FDIS, future edition 1 of IEC 60317-0-9, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2016-06-04
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-06-09
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-9:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 series NOTE  Harmonized in EN 60264 series.
IEC 60317 series NOTE  Harmonized in EN 60317 series.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60172 2015 Test procedure for the determination of the EN 60172 2015
temperature index of enamelled and tape
wrapped winding wires
IEC 60317-0-1 -  Specifications for particular types of EN 60317-0-1 -
winding wires -- Part 0-1: General
requirements - Enamelled round copper
wire
IEC 60851 series Winding wires - Test methods EN 60851 series
ISO 3 -  Preferred numbers; Series of preferred - -
numbers
IEC 60317-0-9 ®
Edition 1.0 2015-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-9: General requirements – Enamelled rectangular aluminium wire

Spécifications pour types particuliers de fils de bobinage –

Partie 0-9: Exigences générales – Fil de section rectangulaire émaillé en

aluminium
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-2667-4

– 2 – IEC 60317-0-9:2015 © IEC 2015
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 8
3.3 Appearance . 8
4 Dimensions. 8
4.1 Conductor dimensions . 8
4.2 Tolerance on conductor dimensions . 9
4.3 Rounding of corners . 9
4.4 Increase in dimensions due to the insulation . 11
4.5 Overall dimensions . 11
4.5.1 Nominal overall dimensions . 11
4.5.2 Minimum overall dimensions . 11
4.5.3 Maximum overall dimensions . 11
5 Electrical resistance . 12
6 Elongation . 12
7 Springiness . 12
8 Flexibility and adherence . 12
8.1 Mandrel winding test . 12
8.2 Adherence test . 12
9 Heat shock . 12
10 Cut-through . 12
11 Resistance to abrasion . 13
12 Resistance to solvents . 13
13 Breakdown voltage . 13
14 Continuity of insulation . 13
15 Temperature index . 13
16 Resistance to refrigerants . 13
17 Solderability . 14
18 Heat or solvent bonding . 14
19 Dielectric dissipation factor . 14
20 Resistance to transformer oil . 14
21 Loss of mass . 14
23 Pin hole test . 14
30 Packaging . 14
Annex A (informative) Nominal cross-sectional areas for preferred and intermediate
sizes . 15
Annex B (informative) Special tolerances . 24

IEC 60317-0-9:2015 © IEC 2015 – 3 –
Bibliography . 25

Table 1– Conductor tolerances . 9
Table 2 – Nominal cross-sectional areas of preferred sizes . 10
Table 3 – Corner radii . 11
Table 4 – Increases in dimensions . 11
Table 5 – Mandrel winding . 12
Table 6 – Breakdown voltage . 13
Table A.1 – Nominal cross-sectional areas (1 of 9) . 15
Table B.1 – Overall dimensional tolerances for grade 2 . 24

– 4 – IEC 60317-0-9:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-9: General requirements – Enamelled rectangular aluminium wire

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
...