EN 60598-1:2015
(Main)Luminaires - Part 1: General requirements and tests
Luminaires - Part 1: General requirements and tests
IEC 60598-1:2014 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction, electrical construction and photobiological safety. This eighth edition cancels and replaces the seventh edition published in 2008. This edition constitutes a technical revision and includes the following significant technical changes with respect to the previous edition: a) requirements to support the construction methods for new LED luminaires entering the market; b) photobiological requirements extended; c) more precise requirements for insulation between different types of electrical circuit; d) other general updates and improvements.
Leuchten - Teil 1: Allgemeine Anforderungen und Prüfungen
Luminaires - Partie 1: Exigences générales et essais
L'IEC 60598-1:2014 spécifie pour les luminaires incorporant des sources lumineuses électriques, les exigences générales pour le fonctionnement à des tensions d'alimentation jusqu'à 1 000 V. Les exigences et les essais correspondants de cette norme concernent: la classification, le marquage, la construction mécanique et électrique. Cette huitième édition annule et remplace la septième édition parue en 2008. Cette édition constitue une révision technique et inclue les changements techniques significatifs suivants par rapport à l'édition précédente: a) exigences pour aider aux méthodes de construction des nouveaux luminaires à LED entrant sur le marché; b) exigences photobiologiques étendues; c) exigences plus précises concernant l'isolation entre les différents types de circuits électriques; d) autres mises à jour générales et améliorations.
Svetilke - 1. del: Splošne zahteve in preskusi (IEC 60598-1:2014, spremenjen)
Ta 1. del standarda IEC 60598 določa splošne zahteve za svetilke, ki vsebujejo električne svetlobne vire, namenjene za delovanje z omrežnim napajanjem do 1000 V. Zahteve in preskusi iz tega standarda zajemajo: klasifikacijo, označevanje, mehansko zasnovo, električno zasnovo in fotobiološko varnost.
Vse oddelke 1. dela je treba brati v povezavi s tem oddelkom 0 in drugimi ustreznimi oddelki, na katere se sklicuje besedilo.
V vsakem delu standarda IEC 60598-2 so navedene podrobne zahteve za določeno vrsto svetilk ali skupino svetilk z omrežnim napajanjem, ki ne presega 1000 V. Ti deli so zaradi lažjega revidiranja objavljeni ločeno, po potrebi pa bodo dodani dodatni oddelki.
Predstavitev fotometričnih podatkov za svetilke obravnava Mednarodna komisija za razsvetljavo (CIE), zato ni zajeta v 1. delu.
1. del zajema zahteve za svetilke, ki vsebujejo sprožilce z nazivnimi najvišjimi vrednostmi napetostnega impulza, ki ne presegajo tistih v preglednici 11.2. Zahteve veljajo za svetilke s sprožilci, vgrajenimi v dušilke, in za svetilke, pri katerih so sprožilci ločeni od dušilk. Za svetilke, pri katerih so sprožilci vgrajeni v same sijalke, so zahteve še v obravnavi. 1. del zajema tudi zahteve za polsvetilke.
Na splošno 1. del zajema varnostne zahteve za svetilke. Namen 1. dela je določiti nabor zahtev in preskusov, ki jih je na splošno mogoče uporabiti za večino vrst svetilk in na katere se je mogoče sklicevati, kot zahtevajo podrobne specifikacije standarda IEC 60598-2. 1. dela tako samega ni mogoče obravnavati kot specifikacijo za nobeno vrsto svetilk, njegove določbe pa veljajo samo za določene vrste svetilk, in sicer v obsegu, kot ga določa ustrezni del standarda IEC 60598-2. Deli standarda IEC 60598-2 pri sklicevanju na posamezni oddelek 1. dela določajo obseg, v katerem se ta oddelek uporablja, in vrstni red, v katerem je treba izvesti preskuse; po potrebi zajemajo tudi dodatne zahteve.
Vrstni red, v katerem so oštevilčeni oddelki 1. dela, nima posebnega pomena, saj je vrstni red, v katerem veljajo določbe, za vsako vrsto svetilk ali skupino svetilk določen v ustreznem delu standarda IEC 60598-2. Vsi deli standarda IEC 60598-2 so samostojni in ne vsebujejo sklicev na druge dele tega standarda. Kadar so v delih standarda IEC 60598-2 navedeni sklici na zahteve katerega koli oddelka 1. dela z besedno zvezo »Upoštevati je treba zahteve .... oddelka standarda IEC 60598-1«, je treba to besedno zvezo razumeti tako, da veljajo vse zahteve tega oddelka 1. dela, razen tistih, ki so jasno neprimerne za določeno vrsto svetilk, ki je obravnavana v tistem delu standarda IEC 60598-2.
Za svetilke, odporne proti eksploziji, ki so obravnavane v standardu IEC 60079, se poleg zahtev standarda IEC 60079 uporabljajo tudi zahteve standarda IEC 60598 (izbrane iz ustreznih delov 2. dela). V primeru neskladij med standardoma IEC 60598 in IEC 60079 imajo prednost zahteve standarda IEC 60079. Opozoriti je treba na standarde glede zmogljivosti sijalk, ki vsebujejo »informacije o zasnovi svetilk«; te je treba upoštevati za pravilno delovanje sijalk; vendar pa ta standard ne zahteva, da homologacijski preskusi svetilk zajemajo preskušanje zmogljivosti sijalk. Izboljšave varnosti, ki upoštevajo najsodobnejšo tehnologijo, se redno dodajajo v standarde z revizijami in dopolnili. Regionalni organi za standardizacijo lahko v svoje izpeljane standarde dodajo navedbe o izdelkih, ki so bili skladni s predhodnim dokumentom, kot je prikazal proizvajalec ali organ za standardizacijo. V navedbah se lahko zahteva, da se pri proizvodnji takih izdelkov še naprej uporablja predhodni standard, in sicer do določenega datuma, od katerega dalje se bo uporabljal novi standard.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Svetilke - 1. del: Splošne zahteve in preskusi (IEC 60598-1:2014, spremenjen)Leuchten - Teil 1: Allgemeine Anforderungen und Prüfungen (IEC 60598-1:2014 , modifiziert)Luminaires - Partie 1: Exigences générales et essais (IEC 60598-1:2014 , modifiée)Luminaires - Part 1: General requirements and tests (IEC 60598-1:2014 , modified)29.140.40SvetilaLuminairesICS:Ta slovenski standard je istoveten z:EN 60598-1:2015SIST EN 60598-1:2015en01-maj-2015SIST EN 60598-1:2015SLOVENSKI
STANDARDSIST EN 60598-1:2009/A11:2009SIST EN 60598-1:20091DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60598-1
January 2015 ICS 29.140.40 Supersedes EN 60598-1:2008
English Version
Luminaires -
Part 1: General requirements and tests (IEC 60598-1:2014 , modified)
Luminaires -
Partie 1: Exigences générales et essais (IEC 60598-1:2014 , modifiée)
Leuchten -
Teil 1: Allgemeine Anforderungen und Prüfungen (IEC 60598-1:2014 , modifiziert) This European Standard was approved by CENELEC on 2014-10-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60598-1:2015 E SIST EN 60598-1:2015
This document supersedes EN 60598-1:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC). Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 60598-1:2014 are prefixed “Z”. Endorsement notice The text of the International Standard IEC 60598-1:2014 was approved by CENELEC as a European Standard with agreed common modifications.
- 3 - EN 60598-1:2015 COMMON MODIFICATIONS 3 Marking 3.2.12 Delete NOTE 4. 3.3 Add a new subclause:
3.3.101 Where the terminal block is not supplied with the luminaire, the packaging needs to contain the following wording:
"Terminal block not included. Installation may require advice from a qualified person.” 4 Construction 4.11.6 At the end of the paragraph commencing "Following completion of these tests.", add "[the test voltage however being reduced to 1 500 V]". 5 External and internal wiring 5.2.1 Add under the item ‘connecting leads (tails)’, related to the indent "Fixed luminaires" the following additional text:
connecting leads (tails):
account shall be taken of national installation rules/practice when deciding whether to supply a connection device or not. Where the luminaire is delivered with connecting leads (tails) and without a means of connection to the supply, the manufacturer of the luminaire shall specify which terminal block may be used which shall conform to EN 60998-2-1 or EN 60998-2-2; either the terminal block to be used shall be specified or the following shall be defined: - the type of terminal (screw/screwless); - number of terminals; - rated voltage; - rated connecting capacity; - any necessary preparation of the ends of conductors; - any fixing method. The requirements of 4.6, 4.7.1, 4.7.2, 4.10.1, 11.2, 12 and 13.2 shall be applied. 5.2.2 In paragraph 1, replace "IEC 60227 and IEC 60245" by "EN 50525". Delete paragraph 2. SIST EN 60598-1:2015
H03RT-H c
H03VVH2-F c H03VV-F c
Ordinary class II luminaires
H05RR-F c H03VVH2-F (c H03VV-F c Luminaires other than ordinary class I and II
H05RN-F c H03VVH2-F(a)c H03VV-F a c Portable rough service luminaires
H07RN-F c - Class III or with SELV circuits luminaires (up to 25V a.c./60V d.c.)
Un-insulated conductor b Class III or with SELV circuits luminaires (above 25V a.c./60V d.c.), including 50V a.c./120 d.c. Unsheathed basic insulated conductor
a For indoor use only b In accordance to HD 60364 “Electrical installations of buildings” uninsulated conductors are not allowed in certain special installations and locations e.g. HD 60364-7-701 “Locations containing a bath or shower”.
c For supply voltages greater than 250 V, higher voltage grade cables and cords than those given in the above table may be necessary.
12 Endurance test and thermal test 12.4.2 c) Line 2, after “90 °C” add “(see footnote c
to Table 12.2 relating to unsleeved fixed wiring)”. Table 12.2 In footnote c
add the following:
– after “European installation standards”: "(HD 60364 (HD 384))";
– after “European cable standards”: "(EN 50525)". Bibliography
Add the following notes for the standards indicated: IEC 60081:1997 NOTE
Harmonized as EN 60081:1998 (not modified). IEC 60216 Series NOTE
Harmonized as EN 60216 Series (not modified). IEC 60364 Series NOTE
Harmonized as HD 384/HD 60364 Series (partly modified). IEC 60364-5-51:2001 NOTE
Harmonized as HD 60364-5-51:2006 (modified). 1) IEC 60364-7-701 NOTE
Harmonized as HD 60364-7-701. IEC 60364-7-702 NOTE
Harmonized as HD 60364-7-702 ——————— 1) Superseded by HD 60364-5-51:2009. SIST EN 60598-1:2015
- 5 - EN 60598-1:2015 IEC 60598-2-3:2002 NOTE
Harmonized as EN 60598-2-3:2003 (not modified). IEC 60598-2-5:1998 NOTE
Harmonized as EN 60598-2-5:1998 (not modified). IEC 60598-2-6:1994 NOTE
Harmonized as EN 60598-2-6:1994 (not modified). IEC 60664-3:2003 NOTE
Harmonized as EN 60664-3:2003 (not modified). IEC 60695 Series NOTE
Harmonized as EN 60695 Series (not modified). IEC 60695-2-11:2000 NOTE
Harmonized as EN 60695-2-11:2001 (not modified). IEC 60811-3-1:1985 NOTE
Harmonized as EN 60811-3-1:1995 (not modified). IEC 60901:1996 NOTE
Harmonized as EN 60901:1996 (not modified). IEC 60921:2004 NOTE
Harmonized as EN 60921:2004 (not modified). IEC 60923:2005 NOTE
Harmonized as EN 60923:2005 (not modified). IEC 60925:1989 NOTE
Harmonized as EN 60925:1991 (not modified). IEC 60929:2006 NOTE
Harmonized as EN 60929:2006 (not modified). 2) IEC 60950-1:2005 NOTE
Harmonized as EN 60950-1:2006 (modified). IEC 61195:1999 NOTE
Harmonized as EN 61195:1999 (not modified). IEC 61210:1993 NOTE
Harmonized as EN 61210:1995 (modified). 3) IEC 61346-11996 NOTE
Harmonized as EN 61346-1:1996 (not modified). IEC 61535:2009 NOTE
Harmonized as EN 61535:2009 (modified). IEC 61995 Series NOTE
Harmonized as EN 61995 Series (partly modified). ISO 75-2:1993 NOTE
Harmonized as EN ISO 75-2:1996 (not modified). 4) ——————— 2) Superseded by EN 60929:2011. 3) Superseded by EN 61210:2010. 4) Superseded by EN ISO 75-2:2004, which is also superseded by EN ISO 75-2:2013. SIST EN 60598-1:2015
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year
IEC 60061 Series Lamp caps and holders together with gauges for the control of interchangeability and safety
EN 60061 Series
IEC 60061-2 (mod) 1969 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders EN 60061-2 + A1 to A37 1993
IEC 60061-3 1969
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges EN 60061-3 + A1 to A38
IEC 60065 (mod) 2001 Audio, video and similar electronic apparatus - Safety requirements EN 60065 + corr. March + corr. August + A11 + A12 2002 2006 2007 2008 2011
IEC 60068-2-75 1997 Environmental testing -
Part 2-75: Tests - Test Eh: Hammer tests EN 60068-2-75 1997
IEC 60079 Series Explosive atmospheres EN 60079 Series
IEC/TR 60083 – Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC – –
IEC 60085 2007 Electrical insulation - Thermal evaluation and designation EN 60085 2008
IEC 60112
2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials EN 60112 2003
IEC 60155 1993 Glow-starters for fluorescent lamps EN 60155 1995
IEC 60227 Series Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V EN 50525 1) Series
——————— 1) EN 50525 Series, which is related to, but not directly equivalent with IEC 60227 Series, applies instead. SIST EN 60598-1:2015
- 7 - EN 60598-1:2015 Publication Year Title EN/HD Year
IEC 60238 2004 Edison screw lampholders EN 60238 + corr. January 2004 2005
IEC 60245 Series Rubber insulated cables - Rated voltages up to and including 450/750 V EN 505252) Series
IEC 60269 Series Low-voltage fuses
EN/HD 60269 Series
IEC 60320 Series Appliance couplers for household and similar general purposes
EN 60320 Series
IEC 60357 2002 Tungsten halogen lamps (non-vehicle) - Performance specifications EN 60357 + corr. July 2003 2003
IEC 60360 1998 Standard method of measurement of lamp cap temperature rise EN 60360 1998
IEC 60364-4-41 (mod) 2005 Low-voltage electrical installations -
Part 4-41: Protection for safety - Protection against electric shock HD 60364-4-41 + corr. July 2007 2007
IEC 60384-14 2005 Fixed capacitors for use in electronic equipment -
Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains EN 60384-14 2005 3)
IEC 60400 2008 Lampholders for tubular fluorescent lamps and starterholders EN 60400 2008
IEC 60417 data-base Graphical symbols for use on equipment – –
IEC 60432-1 (mod) A1 1999 2005 Incandescent lamps - Safety specifications -
Part 1: Tungsten filament lamps for domestic and similar general lighting purposes EN 60432-1 A1 2000 2005
IEC 60432-2 (mod) A1 (mod) 1999 2005 Incandescent lamps - Safety specifications -
Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes EN 60432-2 A1 2000 2005
IEC 60432-3 2002 Incandescent lamps - Safety specifications -
Part 3: Tungsten-halogen lamps (non-vehicle) EN 60432-3 2003 4)
IEC 60449 + A1 1973 1979 Voltage bands for electrical installations of buildings
HD 193 S2
IEC 60529 1989 Degrees of protection provided by enclosures (IP Code) EN 60529 + corr. May
1991 1993
——————— 2) EN 50525 Series, which is related to, but not directly equivalent with IEC 60245 Series, applies instead. 3) Superseded by EN 60384-14:2013 (DOW = 2016-07-10). 4) Superseded by EN 60432-3:2013 (DOW = 2015-08-08). SIST EN 60598-1:2015
IEC 60570 (mod) 2003 Electrical supply track systems for luminaires EN 60570 2003
IEC 60598-2 Series Luminaires -
Part 2: Particular requirements
EN 60598-2 Series
IEC 60598-2-4 1997 Luminaires -
Part 2: Particular requirements -
Section 4: Portable general purpose luminaires EN 60598-2-4 1997
IEC 60634 1993 Heat test source (H.T.S.) lamps for carrying out heating tests on luminaires EN 60634 1995
IEC 60662 (mod) 1980 High-pressure sodium vapour lamps EN 60662 1993 5)
IEC 60664-1 2007 Insulation coordination for equipment within low-voltage systems -
Part 1: Principles, requirements and tests EN 60664-1 2007
IEC 60682 1980 Standard method of measuring the pinch temperature of quartz-tungsten-halogen lamps EN 60682
IEC 60684 Series Flexible insulating sleeving
EN 60684 Series
IEC 60695-2 Series Fire hazard testing -
Part 2: Glowing/hot-wire based test methods EN 60695-2 Series
IEC 60695-2-10 2000 Fire hazard testing -
Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure EN 60695-2-10 2001 6)
IEC 60695-11-5 2004 Fire hazard testing -
Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance EN 60695-11-5 2005
IEC 60838 Series Miscellaneous lampholders EN 60838 Series
IEC 60989 – Separating transformers, autotransformers, variable transformers and reactors – –
IEC 60990 1999 Methods of measurement of touch current and protective conductor current EN 60990 1999
IEC 61032 1997 Protection of persons and equipment by enclosures - Probes for verification EN 61032 1998
——————— 5) Superseded by EN 60662:2012 (DOW = 2015-01-02). 6) Superseded by EN 60695-2-10:2013 (DOW = 2016-05-14). SIST EN 60598-1:2015
- 9 - EN 60598-1:2015 Publication Year Title EN/HD Year
IEC 61058-1 (mod) 2000 Switches for appliances -
Part 1: General requirements EN 61058-1 2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.