EN IEC 60598-2-23:2021

SLOVENSKI STANDARD
01-marec-2021
Nadomešča:
SIST EN 60598-2-23:1999
SIST EN 60598-2-23:1999/A1:2002
Svetilke - 2-23. del: Posebne zahteve - Malonapetostni svetlobni sistemi za
svetlobne vire ELV (IEC 60598-2-23:2020)
Luminaires - Part 2-23: Particular requirements - Extra-low-voltage lighting systems for
ELV light sources (IEC 60598-2-23:2020)
Leuchten - Teil 2-23: Besondere Anforderungen - Kleinspannungsbeleuchtungssysteme
für Glühlampen (IEC 60598-2-23:2020)
Luminaires - Partie 2-23: Règles particulières - Systèmes d'éclairage à très basse
tension pour lampes à filament (IEC 60598-2-23:2020)
Ta slovenski standard je istoveten z: EN IEC 60598-2-23:2021
ICS:
29.140.40 Svetila Luminaires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60598-2-23

NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2021
ICS 29.140.40 Supersedes EN 60598-2-23:1996 and all of its
amendments and corrigenda (if any)
English Version
Luminaires - Part 2-23: Particular requirements - Extra-low-
voltage lighting systems for ELV light sources
(IEC 60598-2-23:2020)
Luminaires - Partie 2-23: Exigences particulières - Leuchten - Teil 2-23: Besondere Anforderungen -
Systèmes d'éclairage à très basse tension pour sources de Kleinspannungsbeleuchtungssysteme für Glühlampen
lumière TBT (IEC 60598-2-23:2020)
(IEC 60598-2-23:2020)
This European Standard was approved by CENELEC on 2020-08-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60598-2-23:2021 E

European foreword
The text of document 34D/1543/FDIS, future edition 2 of IEC 60598-2-23, prepared by SC 34D
“Luminaires” of IEC/TC 34 “Lighting” was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN IEC 60598-2-23:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-07-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-01-15
document have to be withdrawn
This document supersedes EN 60598-2-23:1996 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 60598-2-23:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61347-2-8 NOTE Harmonized as EN 61347-2-8
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
1)
IEC/TR 60083 2015 Plugs and socket-outlets for domestic and - -
similar general use standardized in
member countries of IEC
IEC 60598-1 - Luminaires - Part 1: General requirements EN 60598-1 2015
and tests + A1 2018
IEC 61347-2-2 - Lamp controlgear - Part 2–2: Particular EN 61347-2-2 2012
requirements for d.c. or a.c. supplied
electronic step-down convertors for
filament lamps
IEC 61347-2-13 - Lamp controlgear - Part 2–13: Particular EN 61347-2-13 2014
requirements for d.c. or a.c. supplied +A1 2017
electronic controlgear for LED modules
IEC 61558-2-6 - Safety of transformers, reactors, power EN 61558-2-6 2009
supply units and similar products for supply
voltages up to 1 100 V - Part 2–6:
Particular requirements and tests for safety
isolating transformers and power supply
units incorporating safety isolating
transformers
IEC 61558-2-16 - Safety of transformers, reactors, power EN 61558-2-16 2009
supply units and similar products for supply +A1 2013
voltages up to 1 100 V - Part 2–16:
Particular requirements and tests for switch
mode power supply units and transformers
for switch mode power supply units

1)
Dated as no equivalent European Standard exist.
Annex ZZ
(informative)
Relationship between this European standard and the safety
objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be
covered
This European Standard has been prepared under a Commission’s standardization request relating to
harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 — Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-clause(s)
Safety objectives of Directive
Remarks / Notes
2014/35/EU
of this EN
1. General conditions
a) the essential characteristics, 23.6
the recognition and observance
of which will ensure that
electrical equipment will be used
safely and in applications for
which it was made, shall be
marked on the electrical
equipment, or, if this is not
possible, on an accompanying
document;
b) the electrical equipment, All
together with its component
parts, shall be made in such a
way as to ensure that it can be
safely and properly assembled
and connected;
c) the electrical equipment shall See item 2 and 3 of this table
be so designed and
manufactured as to ensure that
protection against the hazards
set out in points 2 and 3 is
ensured, providing that the
equipment is used in
applications for which it was
made and is adequately
maintained.
2. Protection against hazards
arising from the electrical
equipment
Measures of a technical nature
shall be laid down in accordance
with point 1, in order to ensure
that:
a) persons and domestic 23.7
animals are adequately
23.8
protected against the danger of
23.9
physical injury or other harm
23.10
which might be caused by direct
or indirect contact; 22.11
22.12
b) temperatures, arcs or 23.7 EMF is not covered
radiation which would cause a
23.8
danger, are not produced;
23.13
23.15
c) persons, domestic animals 23.7
and property are adequately
23.15
protected against non-electrical
23.8
dangers caused by the electrical
equipment which are revealed
by experience;
d) the insulation is suitable for 23.8
foreseeable conditions.
23.14
23.15
3. Protection against hazards
which may be caused by
external influences on the
electrical equipment
Technical measures shall be
laid down in accordance with
point 1, in order to ensure that
the electrical equipment:
a) meets the expected 23.6
mechanical requirements in
23.7
such a way that persons,
domestic animals and property
are not endangered;
b) is resistant to non-mechanical 23.14
influences in expected
23.16
environmental conditions, in
such a way that persons,
domestic animals and property
are not endangered;
c) does not endanger persons, 23.7
domestic animals and property
23.13
in foreseeable conditions of
23.16
overload.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
IEC 60598-2-23 ®
Edition 2.0 2020-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Luminaires –
Part 2-23: Particular requirements – Extra-low-voltage lighting systems

for ELV light sources
Luminaires –
Partie 2-23: Exigences particulières – Systèmes d’éclairage à très basse tension

pour sources de lumière TBT:
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.40 ISBN 978-2-8322-8637-1

– 2 – IEC 60598-2-23:2020 © IEC 2020
CONTENTS
FOREWORD . 3
23.1 Scope . 5
23.2 Normative references . 5
23.3 Terms and definitions . 5
23.4 General test requirements . 7
23.5 Classification . 7
23.6 Marking . 7
23.7 Construction . 8
23.8 Creepage distances and clearances . 9
23.9 Provisions for earthing . 9
23.10 Terminals and electrical connections . 9
23.11 External and internal wiring . 10
23.12 Protection against electric shock . 10
23.13 Endurance tests and thermal tests . 10
23.14 Resistance to dust, solid objects and moisture . 11
23.15 Insulation resistance and electric strength . 11
23.16 Resistance to heat, fire and tracking . 11
Annex A (informative) Schedule of amended subclauses containing more serious/critical
requirements which require products to be retested . 12
Bibliography . 13

Figure 1 – Typical supporting methods for lighting systems . 7

IEC 60598-2-23:2020 © IEC 2020 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LUMINAIRES –
Part 2-23: Particular requirements – Extra-low-voltage
lighting systems for ELV light sources

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity
...