EN IEC 61347-2-13:2024

SLOVENSKI STANDARD
01-februar-2025
Stikalne naprave za sijalke - Varnost - 2-13. del: Posebne zahteve - Elektronske
stikalne naprave za LED-svetlobne vire (IEC 61347-2-13:2024)
Controlgear for electric light sources - Safety - Part 2-13: Particular requirements -
Electronic controlgear for LED light sources (IEC 61347-2-13:2024)
Geräte für elektrische Lichtquellen - Sicherheit - Teil 2-13: Besondere Anforderungen -
elektronische Betriebsgeräte für LED-Lichtquellen (IEC 61347-2-13:2024)
Appareillages de commande pour les sources de lumière électriques - Sécurité - Partie 2
-13 : Exigences particulières - Appareillages électroniques pour les sources de lumière à
LED (IEC 61347-2-13:2024)
Ta slovenski standard je istoveten z: EN IEC 61347-2-13:2024
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61347-2-13

NORME EUROPÉENNE
EUROPÄISCHE NORM December 2024
ICS 29.140.99 Supersedes EN 61347-2-13:2014; EN 61347-2-
13:2014/A1:2017
English Version
Controlgear for electric light sources - Safety - Part 2-13:
Particular requirements - Electronic controlgear for LED light
sources
(IEC 61347-2-13:2024)
Appareillages de commande pour les sources de lumière Geräte für elektrische Lichtquellen - Sicherheit - Teil 2-13:
électriques - Sécurité - Partie 2-13 : Exigences particulières Besondere Anforderungen - elektronische Betriebsgeräte
- Appareillages électroniques pour les sources de lumière à für LED-Lichtquellen
LED (IEC 61347-2-13:2024)
(IEC 61347-2-13:2024)
This European Standard was approved by CENELEC on 2024-10-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61347-2-13:2024 E

European foreword
The text of document 34C/1599/FDIS, future edition 3 of IEC 61347-2-13, prepared by SC 34C
"Auxiliaries for lamps" of IEC/TC 34 "Lighting" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 61347-2-13:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-12-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-12-31
document have to be withdrawn
This document supersedes EN 61347-2-13:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61347-2-13:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 61140 NOTE Approved as EN 61140
IEC 61347-1:2015 NOTE Approved as EN 61347-1:2015 (not modified)
IEC 61347-1:2015/A1:2017 NOTE Approved as EN 61347-1:2015/A1:2021 (not modified)
IEC 61347-2-7 NOTE Approved as EN 61347-2-7
IEC 61347-2-13:2014 NOTE Approved as EN 61347-2-13:2014 (not modified)
IEC 61347-2-13:2014/A1:2016 NOTE Approved as EN 61347-2-13:2014/A1:2017 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61347-1 2024 Controlgear for electric light sources - Safety EN IEC 61347-1 2024
- Part 1: General requirements
IEC 61547 - Equipment for general lighting purposes - EN IEC 61547 -
EMC immunity requirements
IEC 62384 2020 DC or AC supplied electronic controlgear for EN IEC 62384 2020
LED modules - Performance requirements

IEC 61347-2-13 ®
Edition 3.0 2024-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Controlgear for electric light sources – Safety –

Part 2-13: Particular requirements – Electronic controlgear for LED light sources

Appareillages de commande pour les sources de lumière électriques – Sécurité –

Partie 2-13: Exigences particulières – Appareillages électroniques pour les

sources de lumière à LED
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.99  ISBN 978-2-8322-9101-6

– 2 – IEC 61347-2-13:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General requirements . 8
5 General notes on tests . 9
6 Information and marking . 9
6.1 Information and marking items . 9
6.1.1 Mandatory markings . 9
6.1.2 Information to be provided . 9
6.2 Durability and legibility of marking . 9
6.3 Built-in controlgear without an enclosure and integral controlgear . 9
7 Terminals . 10
8 Earthing . 10
9 Protection against accidental contact with hazardous live parts . 10
10 Insulation resistance and electric strength . 10
11 Fault conditions . 10
12 Construction . 10
13 Creepage distances, clearances and distances through insulation . 10
14 Screws, current-carrying parts and connections . 10
15 Resistance to heat, fire and tracking . 10
16 Thermal requirements . 11
16.1 General . 11
16.2 Normal operation . 11
16.3 Abnormal operation . 11
17 Output working voltage (U ) . 11
out
18 Rated output characteristics . 12
Annex A (normative) Additional requirements for centrally supplied controlgear for
emergency lighting . 13
A.1 Marking and information . 13
A.2 General notes on tests . 13
A.3 Operating conditions . 13
A.4 Supply current . 13
A.5 EMC immunity. 14
A.6 Pulse voltage from central battery systems . 14
A.7 Tests for abnormal conditions . 14
A.8 Temperature cycling test and endurance test . 14
A.9 Functional safety (EOF ) . 14
x
Annex B (informative) Schedule of more onerous requirements . 16
Bibliography . 17

Figure 1 – Symbol for electronic controlgear for LED light sources . 9

Table A.1 – Pulse voltages . 14

IEC 61347-2-13:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONTROLGEAR FOR ELECTRIC LIGHT SOURCES –
SAFETY –
Part 2-13: Particular requirements –
Electronic controlgear for LED light sources

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical conte
...