Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2008)

ISO 2081:2008 specifies requirements for electroplated coatings of zinc with supplementary treatments on iron or steel. It includes information to be supplied by the purchaser to the electroplater, and the requirements for heat treatment before and after electroplating.
It is not applicable to zinc coatings applied
to sheet, strip or wire in the non-fabricated form,
to close-coiled springs, or
for purposes other than protective or decorative.
ISO 2081:2008 does not specify requirements for the surface condition of the basis metal prior to electroplating with zinc. However, defects in the surface of the basis metal can adversely affect the appearance and performance of the coating.
The coating thickness that can be applied to threaded components can be limited by dimensional requirements, including class or fit.

Metallische und andere anorganische Überzüge - Galvanische Zinküberzüge auf Eisenwerkstoffen mit zusätzlicher Behandlung (ISO 2081:2008)

Diese Internationale Norm legt Anforderungen an galvanisch abgeschiedene Zinküberzüge auf Eisenwerk¬stoffen mit zusätzlicher Behandlung fest. Sie enthält Informationen, die der Auftraggeber dem galvanischen Betrieb geben muss, sowie Anforderungen an die Wärmebehandlung vor und nach der galvanischen Metallabscheidung.
Sie gilt nicht für Zinküberzüge auf Blechen, Bändern oder Draht in unbearbeiteter Form; für engspiralige Federn; oder für andere Zwecke als Korrosionsschutz oder Dekoration.
Diese Internationale Norm legt keine Anforderungen an die Oberflächenbeschaffenheit des Grundmetalls vor der galvanischen Zinkabscheidung fest. Da das Aussehen und die Gebrauchstauglichkeit von Zinküberzügen von der Beschaffenheit des Grundmetalls abhängt, sollte eine Vereinbarung zwischen den interessierten Parteien getroffen werden, dahingehend, dass das Finish des Grundmetalls für die galvanische Metallabscheidung geeignet sind [siehe 4.1 c) und 4.1 e)].
Die aufzubringende Schichtdicke auf Verbindungselemente mit Gewinde kann durch Abmessungsanforderungen, wie Klasse oder Passung, begrenzt sein. Es wird auf ISO 4042 [1] verwiesen, die die maximale Schichtdicke auf genormten Verbindungselementen mit Gewinde festlegt.

Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques de zinc avec traitements supplémentaires sur fer ou acier (ISO 2081:2008)

L'ISO 2081:2008 spécifie les exigences applicables aux dépôts électrolytiques de zinc avec traitements supplémentaires sur le fer ou l'acier. Elle inclut les informations à fournir par l'acheteur à l'électroplaste ainsi que les exigences relatives au traitement thermique avant et après dépôt électrolytique.
Elle n'est pas applicable aux revêtements de zinc appliqués
sur des tôles, des bandes ou des fils à l'état non façonné,
sur des ressorts à enroulement serré, ou
dans un autre but que la protection ou la décoration.
L'ISO 2081:2008 ne spécifie pas d'exigences relatives à l'état de surface du métal de base avant dépôt électrolytique de zinc. Toutefois, la présence de défauts à la surface du métal de base peut avoir une incidence négative sur l'aspect et la performance du revêtement.
L'épaisseur de revêtement qui peut être appliqué sur des pièces filetées peut être limitée par les exigences dimensionnelles, notamment la classe et l'ajustement.

Kovinske in druge anorganske prevleke - Galvanske prevleke cinka z dodatno obdelavo na železu in jeklu (ISO 2081:2008)

General Information

Status
Withdrawn
Publication Date
14-Dec-2008
Withdrawal Date
20-Mar-2018
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Mar-2018

Relations

Buy Standard

Standard
EN ISO 2081:2009
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kovinske in druge anorganske prevleke - Galvanske prevleke cinka z dodatno obdelavo na železu in jeklu (ISO 2081:2008)Metallische Überzüge - Galvanische Zinküberzüge auf Eisenwerkstoffen mit zusätzlicher Behandlung (ISO 2081:2008)Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques de zinc avec traitements supplémentaires sur fer ou acier (ISO 2081:2008)Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2008)25.220.40Kovinske prevlekeMetallic coatingsICS:Ta slovenski standard je istoveten z:EN ISO 2081:2008SIST EN ISO 2081:2009en01-marec-2009SIST EN ISO 2081:2009SLOVENSKI
STANDARDSIST EN 12329:20001DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 2081December 2008ICS 25.220.40Supersedes EN 12329:2000
English VersionMetallic and other inorganic coatings - Electroplated coatings ofzinc with supplementary treatments on iron or steel (ISO2081:2008)Revêtements métalliques et autres revêtementsinorganiques - Dépôts électrolytiques de zinc avectraitements supplémentaires sur fer ou acier (ISO2081:2008)Metallische Überzüge - Galvanische Zinküberzüge aufEisenwerkstoffen mit zusätzlicher Behandlung (ISO2081:2008)This European Standard was approved by CEN on 19 November 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 2081:2008: ESIST EN ISO 2081:2009

Reference numberISO 2081:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO2081Third edition2008-12-15Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel Revêtements métalliques et autres revêtements inorganiques —Dépôts électrolytiques de zinc avec traitements supplémentaires sur fer ou acier
ISO 2081:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
ISO 2081:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms, definitions, abbreviated terms and symbols.2 3.1 Terms and definitions.2 3.2 Abbreviated terms.2 3.3 Symbols.3 4 Information to be supplied by the purchaser to the electroplater.3 4.1 Essential information.3 4.2 Additional information.3 5 Designation.4 5.1 General.4 5.2 Designation specification.4 5.3 Designation of the basis material.5 5.4 Designation of heat treatment requirements.5 5.5 Examples.5 6 Requirements.6 6.1 Appearance.6 6.2 Thickness.6 6.3 Conversion coatings and other supplementary treatments.6 6.4 Adhesion of zinc and chromate coatings.7 6.5 Accelerated corrosion testing.7 6.6 Stress relief heat treatments before cleaning and metal deposition.9 6.7 Hydrogen-embrittlement-relief heat treatments after electroplating.9 7 Sampling.9 Annex A (normative)
Designation of chromate conversion coatings and other supplementary treatments.10 Annex B (normative)
Measurement of average thickness of coating on small articles.12 Annex C (informative)
Additional information on corrosion resistance, rinsing and drying, processing parts in bulk and dyeing of chromate conversion coatings.13 Bibliography.15
ISO 2081:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2081 was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings, Subcommittee SC 3, Electrodeposited coatings and related finishes. This third edition cancels and replaces the second edition (ISO 2081:1986), which has been technically revised. SIST EN ISO 2081:2009

ISO 2081:2008(E) © ISO 2008 – All rights reserved vIntroduction Zinc coatings are applied to iron or steel articles for protective and decorative purposes by electrodeposition from acid zinc chloride, alkaline non-cyanide zinc, and alkaline zinc cyanide solutions. Electroplated, bright zinc coatings are popular and the processes for preparing bright zinc coatings are widely used. The ability of a zinc coating to prevent corrosion is a function of its thickness and the type of service conditions to which it is exposed. For example, the rate of corrosion of zinc will generally be greater in industrial exposures than in rural ones. The type of service condition should, therefore, be taken into consideration when specifying the minimum coating thickness. Chromate conversion coatings and other supplementary treatments enhance the corrosion resistance of electrodeposited zinc coatings and are commonly applied after electroplating. Because the appearance and serviceability of zinc coatings depends on the surface condition of the basis metal, agreement should be reached between the interested parties that the surface finish of the basis metal is satisfactory for electroplating. Chromate conversion coatings are omitted, or replaced by other conversion coatings, at the specific request of the purchaser. This International Standard provides the codes for all types of chromate conversion and other supplementary coatings. Chemical conversion coatings that do not contain hexavalent chromium or are chromium-free, conforming to this International Standard, are commercially available. The appearance of these substitutes may be different from those produced with hexavalent chromium. All forms of chromate conversion coatings, alternative conversion coatings or substitutes, with the exception of phosphate coatings, can be used and are required to satisfy the corrosion requirements given in this International Standard. Standard designations for metals and alloys can be found in References [6] to [10] in the Bibliography.
INTERNATIONAL STANDARD ISO 2081:2008(E) © ISO 2008 – All rights reserved 1Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel WARNING — This International Standard may not be compliant with some countries’ health, safety and environmental legislations and calls for the use of substances and/or procedures that may be injurious to health if adequate safety measures are not taken. This International Standard does not address
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.