iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 16194:2012

(Main)

Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products

Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products

This European Standard applies to mobile toilet cabins that are not connected to a sewerage system.
It specifies requirements of the services relating to the deployment of cabins and the relevant requirements for cabins and sanitary products, taking into account hygiene, health and safety.
It specifies minimum quality requirements relating to cabins and sanitary products and also relating to the extent of cleaning required, the number of cabins to be provided, locations and cleaning/disposal intervals.

Mobile anschlussfreie Toilettenkabinen - Anforderungen an Dienstleistungen und Produkte für den Einsatz von Kabinen und Sanitärprodukten

Diese Europäische Norm gilt für mobile Toilettenkabinen (außer Trockentoiletten), welche nicht an ein Kanalisationssystem angeschlossen sind.
Sie legt Anforderungen fest an die Dienstleistung bezüglich des Einsatzes der Kabinen und die benötigten Anforderungen an Kabinen und Sanitärprodukte unter Berücksichtigung von Hygiene, Gesundheit und Sicherheit.
Sie legt Mindest-Qualitätsvorgaben fest für die Kabinen und Sanitärprodukte sowie für den Reinigungs-umfang, Anzahl der zu stellenden Kabinen, Standorte und Reinigungs-/Entsorgungsintervalle.

Cabines sanitaires mobiles autonomes - Exigences relatives aux services et produits, liées à la mise en place des cabines et des produits sanitaires

La présente Norme européenne s’applique aux cabines sanitaires mobiles (à l’exclusion des toilettes sèches) qui ne sont pas raccordées à un collecteur d’assainissement.
Elle spécifie des exigences relatives aux services liés à la mise en place de cabines et les exigences correspondantes relatives aux cabines et aux produits sanitaires, en tenant compte de l’hygiène, de la santé et de la sécurité.
Elle spécifie des exigences de qualité minimales relatives aux cabines, aux produits sanitaires ainsi qu'au degré de nettoyage exigé, au nombre de cabines devant être fournies, aux emplacements et à la fréquence d’entretien et d'évacuation des effluents.

Premične toaletne kabine brez odvajanja v kanalizacijo - Zahteve za servis in proizvode glede na uporabo kabin in sanitarnih proizvodov

Ta standard zajema zahteve za servis za premične toaletne kabine brez odvajanja v kanalizacijo, pri čemer upošteva tudi higieno, zdravje in varnost. Obravnava tudi minimalne kakovostne zahteve za kabine in sanitarne proizvode.

General Information

Status
Withdrawn
Publication Date
28-Feb-2012
Withdrawal Date
13-Jun-2023
ICS
03.080.30 - Services for consumers
91.040.99 - Other buildings
Technical Committee
CEN/TC 183 - Waste management
Drafting Committee
CEN/TC 183/WG 1 - Waste containers
Current Stage
Ref Project
SIST EN 16194:2012 - Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products

Relations

Replaced By
EN 16194:2023 - Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products
Effective Date
18-Jan-2023

Buy Standard

EN 16194:2012EN 16194:2012
PreviousNext
Standard
EN 16194:2012
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mobile anschlussfreie Toilettenkabinen - Anforderungen an Dienstleistungen und Produkte für den Einsatz von Kabinen und SanitärproduktenCabines sanitaires mobiles autonomes - Exigences relatives aux services et produits, liées à la mise en place des cabines et des produits sanitairesMobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 16194:2012SIST EN 16194:2012en,fr,de01-maj-2012SIST EN 16194:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16194
February 2012 ICS 03.080.30; 91.040.99 English Version
Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products
Cabines sanitaires mobiles autonomes - Exigences relatives aux services et produits, liées à la mise en place des cabines et des produits sanitaires
Mobile anschlussfreie Toilettenkabinen - Anforderungen an Dienstleistungen und Produkte für den Einsatz von Kabinen und Sanitärprodukten This European Standard was approved by CEN on 14 January 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16194:2012: ESIST EN 16194:2012

Legal requirements . 12
Adequate provision of cabins allows hygiene
and privacy.
This European Standard is directed at manufacturers, rental companies and renters of the cabins. 1 Scope This European Standard applies to mobile toilet cabins (excluding dry toilets) that are not connected to a sewerage system. It specifies requirements of the services relating to the deployment of cabins and the relevant requirements for cabins and sanitary products, taking into account hygiene, health and safety. It specifies minimum quality requirements relating to cabins and sanitary products and also relating to the extent of cleaning required, the number of cabins to be provided, locations and cleaning/disposal intervals. SIST EN 16194:2012
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16194:2023(Main)
Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products
SIST EN 16194:2023

This document applies to mobile non-sewer-connected toilet cabins system.
It specifies the requirements for services related to the provision of toilet cabins and the relevant requirements for toilet cabins and sanitary products, taking into account comfort, hygiene, health and safety.
It specifies the minimum quality requirements for toilet cabins and sanitary products, as well as the extent of on-site service and the required disinfection and the number of toilet cabins to be provided. It also determines the frequency of use, the maximum number of uses per toilet cabins, the locations and the intervals for on-site service or disposal of faecal water.
This document is applicable to the framework of activities carried out in the following sectors:
—   construction and extractive industries, opencast or underground;
—   public events and recreational activities, festivals and concerts;
—   agriculture, labour camps and temporary work camps;
—   beaches;
—   emergencies;
—   military tactical and training exercises.
There are other types of mobile toilet cabins which are not connected to a sewage system (e.g. dry toilets, composting toilets, incinerations toilets, vacuum toilets, or other technologies and processes) and which are not covered by this document.
This document establishes a system to ensure that mobile sanitation facilities for waste disposal are available not only in the workplaces but wherever there are no waste disposal systems connected to a sewerage network.
This document is directed at manufacturers, services providers' companies and publics or private cabin hirers of toilet cabins not connected to a sewage network.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16194:2023(Main)
Mobile non-sewer-connected toilet cabins - Requirements of services and products relating to the deployment of cabins and sanitary products
SIST EN 16194:2023

This document applies to mobile non-sewer-connected toilet cabins system.
It specifies the requirements for services related to the provision of toilet cabins and the relevant requirements for toilet cabins and sanitary products, taking into account comfort, hygiene, health and safety.
It specifies the minimum quality requirements for toilet cabins and sanitary products, as well as the extent of on-site service and the required disinfection and the number of toilet cabins to be provided. It also determines the frequency of use, the maximum number of uses per toilet cabins, the locations and the intervals for on-site service or disposal of faecal water.
This document is applicable to the framework of activities carried out in the following sectors:
—   construction and extractive industries, opencast or underground;
—   public events and recreational activities, festivals and concerts;
—   agriculture, labour camps and temporary work camps;
—   beaches;
—   emergencies;
—   military tactical and training exercises.
There are other types of mobile toilet cabins which are not connected to a sewage system (e.g. dry toilets, composting toilets, incinerations toilets, vacuum toilets, or other technologies and processes) and which are not covered by this document.
This document establishes a system to ensure that mobile sanitation facilities for waste disposal are available not only in the workplaces but wherever there are no waste disposal systems connected to a sewerage network.
This document is directed at manufacturers, services providers' companies and publics or private cabin hirers of toilet cabins not connected to a sewage network.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
kSIST FprEN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 18075:2024(Main)
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
kSIST-TS FprCEN/TS 18075:2024

The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
kSIST FprEN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
kSIST FprEN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-2:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 2: Tests for emissions of particulate matter (ISO 18562-2:2024)
kSIST FprEN ISO 18562-2:2024

This document specifies tests for the emissions of particulate matter from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify particles from 0,25 µm diameter to 10 µm diameter that are emitted by the medical device, its parts or accessories into the respirable gas stream. This document establishes acceptance criteria for these tests.
This document does not address nanoparticles. Insufficient data exist to establish exposure limits for particles less than 0,25 µm diameter.
This document does not address particles larger than 10 µm diameter. These particles are deposited in the nasal cavity. Additional information can be needed for medical devices or accessories that bypass the nose. This is outside the scope of this document but can be required by some authorities having jurisdiction.
This document therefore adopts the same approach as the US Environmental Protection Agency (EPA) in setting limits based solely on particle size and not their chemistry.
This document addresses potential contamination of the gas stream arising from the gas pathways, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the particles that are deliberately released by a nebulizer (i.e. the therapeutic agent).
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories, containing gas pathways that are addressed by this document, include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces, and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13997:2024(Main)
Protective clothing - Mechanical properties - Determination of resistance to cutting by sharp objects (ISO 13997:2024)
oSIST prEN ISO 13997:2024

This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17984-1:2024(Main)
Assistance dogs - Part 1: Vocabulary
SIST EN 17984-1:2024

This document specifies the terms and definitions that apply to:
—   different types of assistance dogs;
—   the beneficiary and client services;
—   health and disabilities;
—   assistance dog service providers;
—   assistance dog training staff and related professionals;
—   the socialization and training processes;
—   conformity assessment, identification and registration;
—   accessibility.

  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16709:2024(Main)
Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods
kSIST FprEN 16709:2024

This document specifies requirements and test methods for marketed and delivered high FAME (B20 and B30) diesel fuel for use in diesel engine vehicles designed or subsequently adapted to run on such fuel. High FAME diesel fuel is a mixture of up to 20 % (V/V) in total and up to 30 % (V/V) in total respectively fatty acid methyl esters (commonly known as FAME) complying with EN 14214 and automotive diesel fuel complying with EN 590.
For maintenance and control reasons high FAME (B20 and B30) diesel fuel is to be used in captive fleets that are intended to have an appropriate fuel management (see Clause 4).
NOTE 1   These products are allowed in Europe [4], but national legislation can set additional requirements or rules concerning, or even prohibiting, marketing or delivering of the product.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
NOTE 3   In this document, A-deviations apply (see Annex A).

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day