EN ISO 8062-3:2023
(Main)Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes.
This document does not apply to 3D CAD models used without indicated dimensions.
This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11.
The dimensional tolerances covered by this document are tolerances for linear dimensions.
The geometrical tolerances covered by this document are tolerances for:
— straightness;
— flatness;
— roundness;
— parallelism;
— perpendicularity;
— symmetry;
— coaxiality.
This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances.
This document can be used for the selection of tolerance values for individual indications.
Geometrische Produktspezifikationen (GPS) - Maß-, Form- und Lagetoleranzen für Formteile - Teil 3: Allgemeine Maß-, Form- und Lagetoleranzen und Bearbeitungszugaben für Gussstücke mit ± Toleranzen für die angegebenen Maße (ISO 8062-3:2023)
Dieses Dokument legt allgemeine Maß-, Form- und Lagetoleranzen sowie Grade für Bearbeitungszugaben für Gussstücke im Lieferzustand mit ± Toleranzen für die angegebenen Maße fest, die dem Käufer in Übereinstimmung mit ISO/TS 8062 2 geliefert werden. Es ist anwendbar für Maß-, Form- und Lagetoleranzen von nach verschiedenen Gießverfahren hergestellten Gussstücken aus allen metallischen Gusswerkstoffen und deren Legierungen.
Dieses Dokument ist nicht anwendbar für 3D CAD Modelle, die ohne Maßangaben verwendet werden.
Dieses Dokument ist anwendbar für allgemeine Maß-, Form- und Lagetoleranzen (angegeben im oder nahe am Zeichnungsschriftfeld der Zeichnung) falls nichts anderes festgelegt ist und wo besonders in der Zeichnung auf Hinweise von Abschnitt 11 Bezug genommen wird.
Die in diesem Dokument enthaltenen Maßtoleranzen sind Toleranzen für Längenmaße.
Die in diesem Dokument enthaltenen Form- und Lagetoleranzen sind Toleranzen für:
— Geradheit;
— Ebenheit;
— Rundheit;
— Parallelität;
— Rechtwinkligkeit;
— Symmetrie;
— Koaxialität.
Dieses Dokument behandelt keine anderen Lagetoleranzen, Winkelmaßtoleranzen oder Zylindrizitätstoleranzen.
Dieses Dokument kann für die Auswahl von individuellen Toleranzwerten angewendet werden.
Spécification géométrique des produits (GPS) - Tolérances dimensionnelles et géométriques des pièces moulées - Partie 3: Tolérances dimensionnelles et géométriques générales et surépaisseurs d'usinage pour les pièces moulées utilisant des tolérances ± pour les dimensions indiquées (ISO 8062-3:2023)
Le présent document spécifie les tolérances dimensionnelles et géométriques générales ainsi que les classes de surépaisseur d'usinage pour les pièces moulées utilisant des tolérances ± pour les dimensions indiquées telles que livrées à l'acheteur conformément à l'ISO/TS 8062‑2. Il s'applique au tolérancement des dimensions et de la géométrie des pièces moulées en tous métaux et leurs alliages, produites par différents procédés de fabrication par moulage.
Le présent document ne s'applique pas aux modèles CAO 3D utilisés sans dimension indiquée.
Le présent document s'applique à la fois aux tolérances dimensionnelles et géométriques générales (auxquelles il est fait référence dans ou à proximité du cartouche du dessin), sauf spécification contraire et là où il est fait une mention particulière sur le dessin selon l'une des références de l'Article 11.
Les tolérances dimensionnelles couvertes par le présent document sont les tolérances pour des dimensions linéaires.
Les tolérances géométriques couvertes par le présent document sont des tolérances pour:
— la rectitude;
— la planéité;
— la circularité;
— le parallélisme;
— la perpendicularité;
— la symétrie;
— la coaxialité.
Le présent document ne couvre pas les autres tolérances de localisation, dimensionnelles angulaires ou de cylindricité.
Le présent document peut être utilisé pour le choix des valeurs de tolérance pour des indications individuelles.
Specifikacija geometrijskih veličin izdelka (GPS) - Dimenzijske in geometrijske tolerance zaformanih delov - 3. del: Splošne dimenzijske in geometrijske tolerance ter dodatki za strojno obdelavo ulitkov z uporabo ± toleranc za navedene dimenzije (ISO 8062-3:2023)
Ta dokument določa splošne pogoje za termomehansko analizo termoplastičnih ali termoaktivnih materialov s polnilom ali brez njega v obliki pločevine ali oblikovanih delov.
Termomehanska analiza vključuje ugotavljanje deformacij na preskusnem vzorcu pod stalno obremenitvijo kot funkcijo temperature in/ali časa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2023
Specifikacija geometrijskih veličin izdelka (GPS) - Dimenzijske in geometrijske
tolerance zaformanih delov - 3. del: Splošne dimenzijske in geometrijske tolerance
ter dodatki za strojno obdelavo ulitkov z uporabo ± toleranc za navedene
dimenzije (ISO 8062-3:2023)
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for
moulded parts - Part 3: General dimensional and geometrical tolerances and machining
allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
Geometrische Produktspezifikationen (GPS) - Maß-, Form- und Lagetoleranzen für
Formteile - Teil 3: Allgemeine Maß-, Form- und Lagetoleranzen und
Bearbeitungszugaben für Gussstücke mit ± Toleranzen für die angegebenen Maße (ISO
8062-3:2023)
Spécification géométrique des produits (GPS) - Tolérances dimensionnelles et
géométriques des pièces moulées - Partie 3: Tolérances dimensionnelles et
géométriques générales et surépaisseurs d'usinage pour les pièces moulées utilisant
des tolérances ± pour les dimensions indiquées (ISO 8062-3:2023)
Ta slovenski standard je istoveten z: EN ISO 8062-3:2023
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8062-3
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2023
EUROPÄISCHE NORM
ICS 17.040.10 Supersedes EN ISO 8062-3:2007, EN ISO 8062-
3:2007/AC:2009
English Version
Geometrical product specifications (GPS) - Dimensional
and geometrical tolerances for moulded parts - Part 3:
General dimensional and geometrical tolerances and
machining allowances for castings using ± tolerances for
indicated dimensions (ISO 8062-3:2023)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikationen (GPS) - Maß-,
Tolérances dimensionnelles et géométriques des Form- und Lagetoleranzen für Formteile - Teil 3:
pièces moulées - Partie 3: Tolérances dimensionnelles Allgemeine Maß-, Form- und Lagetoleranzen und
et géométriques générales et surépaisseurs d'usinage Bearbeitungszugaben für Gussstücke mit ± Toleranzen
pour les pièces moulées utilisant des tolérances ± pour für die angegebenen Maße (ISO 8062-3:2023)
les dimensions indiquées (ISO 8062-3:2023)
This European Standard was approved by CEN on 30 December 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8062-3:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 8062-3:2023) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 190 “Foundry technology” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2023, and conflicting national standards
shall be withdrawn at the latest by September 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8062-3:2007.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8062-3:2023 has been approved by CEN as EN ISO 8062-3:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 8062-3
Second edition
2023-02
Geometrical product specifications
(GPS) — Dimensional and geometrical
tolerances for moulded parts —
Part 3:
General dimensional and geometrical
tolerances and machining allowances
for castings using ± tolerances for
indicated dimensions
Spécification géométrique des produits (GPS) — Tolérances
dimensionnelles et géométriques des pièces moulées —
Partie 3: Tolérances dimensionnelles et géométriques générales
et surépaisseurs d'usinage pour les pièces moulées utilisant des
tolérances ± pour les dimensions indiquées
Reference number
ISO 8062-3:2023(E)
ISO 8062-3:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8062-3:2023(E)
Contents Page
Foreword .iv
Introduction . vi
1 S c op e . 1
2 N ormative references . 1
3 Terms and definitions . 2
4 Abbr ev i at ed t er m s . 3
5 Tap er . 3
6 D raft angles (taper) . 4
7 T olerance grades . .7
7.1 G eneral . 7
7.2 D imensional casting tolerance grades (DCTG) . 7
7.3 G eometrical casting tolerance grades (GCTG) . 9
7.3.1 General . 9
7. 3 . 2 Nom i n a l d i men s ion s . 9
7. 3 . 3 Dat u m s . 9
8 S urface mismatch (SMI) .12
9 W all thickness.12
10 Re quired machining allowances (RMA) .12
10.1 G eneral .12
10.2 R equired machining allowance grades (RMAG) . 13
11 Indication on drawings .13
11.1 I ndication of general DCTs . 13
11.2 I ndication of machining allowances . 14
11.3 I ndication of geometrical casting tolerances (GCTs) . 14
12 R ejection .15
Annex A (informative) Dimensional and geometrical tolerances for castings .16
Annex B (informative) Required machining allowance grades (RMAG).19
Annex C (informative) Concept of general tolerancing of characteristics.20
Annex D (informative) Datums for general geometrical tolerances .22
Annex E (informative) Application of general geometrical tolerances for castings .26
Annex F (informative) Relation to the GPS matrix model .33
Bibliography .34
iii
ISO 8062-3:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.