EN 1976:2012
(Main)Copper and copper alloys - Cast unwrought copper products
Copper and copper alloys - Cast unwrought copper products
This European Standard specifies the composition and physical properties of cast unwrought copper products (refinery shapes) in thirteen grades of copper and nine silver-bearing copper grades. The refinery shapes included are horizontally, vertically and continuously cast wire bars, cakes, billets and ingots. Wire bars, cakes and billets are intended for fabricating into wrought products; ingots are intended for alloying in wrought and cast copper alloys.
A table indicating the refinery shapes in which each copper grade is normally available is given in Annex A. Annex B gives information on the relationships between electrical resistivity and conductivity of copper.
Kupfer und Kupferlegierungen - Gegossene Rohformen aus Kupfer
Diese Europäische Norm legt die Zusammensetzung und die physikalischen Eigenschaften von gegossenen Rohformen aus Kupfer (Gussformate) für dreizehn Kupfersorten und neun silberhaltige Kupfersorten fest. Die Gussformate umfassen horizontal, vertikal und kontinuierlich gegossene Drahtbarren, Walzplatten, Rund-blöcke und Blockmetalle. Drahtbarren, Walzplatten und Rundblöcke sind zur Herstellung von Knetprodukten, Blockmetalle zum Legieren von Kupfer-Knetlegierungen und Kupfer-Gusslegierungen, vorgesehen.
Eine Tabelle in Anhang A gibt die Gussformate wieder, in denen die jeweilige Kupfersorte üb¬licherweise erhältlich ist. Anhang B beschreibt die Beziehung zwischen spezifischem elektrischen Widerstand und spezifischer elektrischer Leitfähigkeit von Kupfer.
Cuivre et alliages de cuivre - Formes brutes de coulée en cuivre
La présente Norme européenne spécifie la composition et les propriétés physiques des formes brutes de coulée en cuivre en treize nuances de cuivre et neuf nuances de cuivre à l’argent. Les formes brutes de coulée considérées sont des barres à fil, plateaux, billettes et lingots moulés par coulée continue horizontalement ou verticalement. Les barres à fil, plateaux et billettes sont destinés à être transformés en produits corroyés ; les lingots sont destinés à être transformés en alliages de cuivre corroyés et moulés.
Un tableau indiquant les formes brutes de coulée sous lesquelles chaque nuance de cuivre est normalement disponible est donné en Annexe A. L’Annexe B donne des informations sur les relations entre la résistivité électrique et la conductivité du cuivre.
Baker in bakrove zlitine - Uliti negneteni polizdelki iz bakra
Ta evropski standard določa sestavo in fizične lastnosti ulitih negnetenih izdelkov iz bakra (rafinirane oblike) v trinajstih razredih bakra in devetih razredih bakra s srebrom. Vključene rafinirane oblike so vodoravno, navpično in kontinuirno lite žične palice, plošče, kovinske palice in ingoti. Žične palice, plošče in kovinske palice so namenjene izdelovanju gnetenih izdelkov, ingoti pa so namenjeni legiranju v gnetenih in ulitih bakrovih zlitinah. Tabela, ki označuje rafinirane oblike, v katerih je običajno razpoložljiv posamezni razred bakra, je podana v dodatku A. Dodatek B navaja informacije o razmerju med električno upornostjo in prevodnostjo bakra.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Uliti negneteni polizdelki iz bakraKupfer und Kupferlegierungen - Gegossene Rohformen aus KupferCuivre et alliages de cuivre - Formes brutes de coulée en cuivreCopper and copper alloys - Cast unwrought copper products77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 1976:2012SIST EN 1976:2014en,fr,de01-julij-2014SIST EN 1976:2014SLOVENSKI
STANDARDSIST EN 1976:19991DGRPHãþD
SIST EN 1976:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1976
October 2012 ICS 77.150.30 Supersedes EN 1976:1998English Version
Copper and copper alloys - Cast unwrought copper products
Cuivre et alliages de cuivre - Formes brutes de coulée en cuivre
Kupfer und Kupferlegierungen - Gegossene Rohformen aus Kupfer This European Standard was approved by CEN on 18 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1976:2012: ESIST EN 1976:2014
EN 1976:2012 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Designations .54.1Material .54.2Product .55Ordering information .66Requirements .76.1Composition .76.2Electrical properties .76.3Hydrogen embrittlement . 126.4Scale adhesion . 136.5Dimensions, mass and tolerances . 136.6Physical condition of refinery shapes . 157Sampling . 167.1Arrangement of lots for sampling purposes . 167.2Inspection lots for analysis and physical testing .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.