EN ISO 15792-3:2008

SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN 1597-3:1998
Dodajni materiali za varjenje - Preskusne metode - 3. del: Preskušanje primernosti
dodajnih materialov za varjenje v legah in prevaritev korena pri kotnih varih (ISO
15792-3:2000 including Cor 1:2006)
Welding consumables - Test methods - Part 3: Classification testing of positional
capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000
including Cor 1:2006)
Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur Einteilung der Schweißzusätze
nach ihrer Eignung für Schweißpositionen und Wurzeleinbrand an Kehlnähten (ISO
15792-3:2000, enthält Cor. 1:2006)
Produits consommables pour le soudage - Méthodes d'essai - Partie 3: Évaluation de
l'aptitude au soudage en position et de la pénétration en racine des produits
consommables pour les soudures d'angle (ISO 15792-3:2000, Cor 1:2006 inclus)
Ta slovenski standard je istoveten z: EN ISO 15792-3:2008
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15792-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 25.160.20 Supersedes EN 1597-3:1997
English Version
Welding consumables - Test methods - Part 3: Classification
testing of positional capacity and root penetration of welding
consumables in a fillet weld (ISO 15792-3:2000 including Cor
1:2006)
Produits consommables pour le soudage - Méthodes Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur
d'essai - Partie 3: Évaluation de l'aptitude au soudage en Einteilung der Schweißzusätze nach ihrer Eignung für
position et de la pénétration en racine des produits Schweißpositionen und Wurzeleinbrand an Kehlnähten
consommables pour les soudures d'angle (ISO 15792- (ISO 15792-3:2000, enthält Cor. 1:2006)
3:2000, Cor 1:2006 inclus)
This European Standard was approved by CEN on 5 April 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-3:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
The text of ISO 15792-3:2000/Cor 1:2006 has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” of the International Organization for Standardization (ISO) and has been taken over as
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn
at the latest by November 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1597-3:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15792-3:2000/Cor 1:2006 has been approved by CEN as a EN ISO 15792-3:2008 without any
modification.
INTERNATIONAL ISO
STANDARD 15792-3
First edition
2000-12-15
Welding consumables — Test methods —
Part 3:
Classification testing of positional capacity
and root penetration of welding
consumables in a fillet weld
Produits consommables pour le soudage — Méthodes d'essai —
Partie 3: Évaluation de l'aptitude au soudage en position et de la
pénétration en racine des produits consommables pour les soudures
d'angle
Reference number
ISO 15792-3:2000(E)
©
ISO 2000
ISO 15792-3:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

ISO 15792-3:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15792 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15792-3 was prepared by Technical Committee ISO/TC 44, Welding and allied
processes, Subcommittee SC 3, Welding consumables.
� Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys
� Part 2: Preparation of single-run and two-run technique test specimens in steel
� Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld
ISO 15792-3:2000(E)
Introduction
This part of ISO 15792 describes preparation and assessment of a fillet weld test piece.
Test conditions prescribed and results required should not be considered to be requirements or expectations for a
procedure quali
...