EN 14893:2014
(Main)LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres
LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres
This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1 000 l for Liquefied Petroleum Gases (LPG).
Vertical and horizontal cylindrical receptacles are covered.
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, geschweißte Druckfässer aus Stahl für Flüssiggas (LPG) mit einem Fassungsraum zwischen 150 Liter und 1 000 Liter
Diese Europäische Norm legt die Mindestanforderungen an Werkstoff, Auslegung, Bau, Ausführung, Ausrüstung, Inspektion und Prüfung fest, die bei der Herstellung von ortsbeweglichen, wiederbefüllbaren, geschweißten Druckfässern aus Stahl für Flüssiggas (LPG) mit einem Fassungsraum (Fassungsvermögen) von 150 l bis einschließlich 1 000 l gelten.
Behandelt werden liegende und stehende Druckfässer.
Équipements pour GPL et leurs accessoires - Fûts à pression métalliques transportables pour GPL d'une capacité comprise entre 150 litres et 1 000 litres
La présente Norme européenne spécifie les exigences minimales relatives aux matériaux, à la conception, à la fabrication et à la qualité d'exécution, à l'équipement, à l'inspection et aux essais en usine de fûts à pression en acier soudé transportables et rechargeables, ayant un volume compris entre 150 l et 1 000 l, pour gaz de pétrole liquéfiés (GPL).
Les récipients cylindriques verticaux et horizontaux sont couverts par la présente norme.
Oprema in pribor za utekočinjeni naftni plin (UNP) - Premični varjeni jekleni tlačni sodi za utekočinjeni naftni plin (UNP) s prostornino med 150 in 1000 litri
EN 14893 določa minimalne zahteve za material, zasnovo, konstrukcijo, izdelavo, opremljanje, pregledovanje in preskušanje premičnih povratnih varjenih jeklenih tlačnih sodov za utekočinjeni naftni plin (UNP) s prostornino med 150 in 1000 litri pri proizvajalcu. Vključeni so navpični in vodoravni valjasti vsebniki.
General Information
Relations
Overview
EN 14893:2014 is the CEN European standard for transportable, refillable welded steel pressure drums used with Liquefied Petroleum Gas (LPG). It applies to vertical and horizontal cylindrical receptacles with a nominal capacity over 150 litres up to and including 1 000 litres. The standard defines minimum requirements for materials, design, construction, workmanship, equipping, inspection and factory testing of these pressure drums to ensure safe manufacture and use.
Key Topics and Requirements
This standard covers technical areas critical to safe LPG drum production and certification:
- Scope & definitions - applicability to transportable LPG welded steel pressure drums and relevant terminology.
- Materials - suitability of steel for pressure-retaining and non-pressure parts; certification of material batches and gaskets.
- Design requirements - calculation pressure, design temperature, vacuum conditions, thickness calculation, supports, lifting lugs, openings and reinforcement.
- Welding & workmanship - welding procedure specifications (WPS), welder qualification, acceptable weld details, preheating and post‑weld heat treatment.
- Non-destructive testing (NDT) - permitted NDT methods including radiography, ultrasonic testing, magnetic particle and dye penetrant testing, plus acceptance criteria.
- Manufacture controls - traceability, tolerances, formed part testing, repairs, and marking of components.
- Factory testing & inspection - pressure tests, leak tightness, lifting lug tests, tare mass verification, final examination and conformity verification.
- Design type testing - fatigue, burst and drop testing provisions for design validation.
- Surface treatment & marking - finishing, protective coatings and essential product marking.
- Documentation & record keeping - manufacturer records, inspection certificates and conformity documentation.
Applications and Who Uses It
EN 14893:2014 is used by organizations responsible for the safe production, certification and use of LPG transportable drums:
- Manufacturers of refillable welded steel LPG drums - to design and produce compliant drums.
- Design engineers and pressure-vessel specialists - for calculations, material selection and structural design.
- Quality & welding inspectors - to apply NDT and acceptance criteria.
- Certification bodies and notified bodies - for conformity assessment and type-testing programs.
- LPG distributors, transport operators and asset managers - to verify supplier compliance and ensure safe handling, transport and refilling operations.
- Regulators and safety officers - for harmonized safety requirements across CEN member states.
Related Standards
- EN 14893:2014 supersedes earlier editions (e.g., EN 14893:2006).
- As a CEN standard, it is intended to be adopted nationally across European standards bodies.
Keywords: EN 14893:2014, LPG welded steel pressure drums, transportable LPG drums, pressure vessels, welded steel pressure drums, NDT, pressure testing, CEN standard.
Frequently Asked Questions
EN 14893:2014 is a standard published by the European Committee for Standardization (CEN). Its full title is "LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres". This standard covers: This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1 000 l for Liquefied Petroleum Gases (LPG). Vertical and horizontal cylindrical receptacles are covered.
This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1 000 l for Liquefied Petroleum Gases (LPG). Vertical and horizontal cylindrical receptacles are covered.
EN 14893:2014 is classified under the following ICS (International Classification for Standards) categories: 23.020.30 - Pressure vessels, gas cylinders; 23.020.35 - Gas cylinders. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 14893:2014 has the following relationships with other standards: It is inter standard links to EN 14893:2006, EN 14893:2006/AC:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 14893:2014 is associated with the following European legislation: EU Directives/Regulations: 2008/68/EC; Standardization Mandates: M/086. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 14893:2014 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, geschweißte Druckfässer aus Stahl für Flüssiggas (LPG) mit einem Fassungsraum zwischen 150 Liter und 1 000 LiterÉquipements pour GPL et leurs accessoires - Fûts à pression métalliques transportables pour GPL d'une capacité comprise entre 150 litres et 1 000 litresLPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 14893:2014SIST EN 14893:2014en,fr,de01-julij-2014SIST EN 14893:2014SLOVENSKI
STANDARDSIST EN 14893:2007/AC:2007SIST EN 14893:20071DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14893
May 2014 ICS 23.020.30 Supersedes EN 14893:2006English Version
LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres
Équipements pour GPL et leurs accessoires - Fûts à pression métalliques transportables pour GPL d'une capacité comprise entre 150 litres et 1 000 litres
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, geschweißte Druckfässer aus Stahl für Flüssiggas (LPG) mit einem Fassungsraum zwischen 150 Liter und 1 000 Liter This European Standard was approved by CEN on 5 January 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14893:2014 ESIST EN 14893:2014
Guidance on selection of material grades . 33 Annex B (normative)
Tolerances on drums . 34 B.1 Mean external diameter . 34 B.2 Out of roundness . 34 B.3 Deviation from the straight line . 34 B.4 Irregularities in circular profile . 34 B.5 Thickness tolerance . 35 B.6 Profile . 35 B.7 Surface alignment . 36 B.8 Attachments, nozzles and fittings . 36 Annex C (normative)
Hydraulic pressure test . 37 C.1 Temporary fittings . 37 C.2 Pressure gauges . 37 C.3 Pressurising agent. 37 C.4 Avoidance of shocks . 37 C.5 Test procedure . 37 Annex D (normative)
Imperfections of welded joints . 38 Annex E (normative)
Design formulae for drums . 41 E.1 Allowable stresses. 41 E.2 Design formulae . 41 E.3 Nozzle reinforcement . 44 Annex F (informative)
Measurement of shell peaking . 52 F.1 Profile gauge . 52 F.2 Peaking survey . 52 Annex G (informative)
Examples of welded joints . 55 Annex H (informative)
Environmental checklist . 59 Bibliography . 60
1) Issued by the American National Standards Institute (1983). SIST EN 14893:2014
Steels with a specified minimum yield strength ReH ≤ 460 N/mm2 a and with analysis in %: C ≤ 0,25 Si ≤ 0,60 Mn ≤ 1,70 Mo ≤ 0,70 b S ≤ 0,045 P ≤ 0,045 Cu ≤ 0,40 b Ni ≤ 0,5 b Cr ≤ 0,3 (0,4 for castings) b Nb ≤ 0,05 V ≤ 0,12 b Ti ≤ 0,05 1.1 Steels with a specified minimum yield strength ReH ≤ 275 N/mm2 1.2 Steels with a specified minimum yield strength 275 N/mm2 < ReH ≤ 360 N/mm2 1.3 Normalized fine grain steels with a specified minimum yield strength ReH > 360 N/mm2 2
Thermomechanically treated fine grain steels and cast steels with a specified minimum yield strength ReH > 360 N/mm2 2.1 Thermomechanically treated fine grain steels and cast steels with a specified minimum yield strength 360 N/mm2 < ReH ≤ 460 N/mm2 2.2 Thermomechanically treated fine grain steels and cast steels with a specified minimum yield strength ReH > 460 N/mm2 NOTE This table is an extract from CEN ISO/TR 15608:2013 [10]. a In accordance with the specification of the steel product standards, ReH may be replaced by Rp0,2. b A higher value is accepted provided that Cr + Mo + Ni + Cu + V ≤ 0,75 %. SIST EN 14893:2014
...
記事のタイトル: EN 14893:2014 - LPG装置とアクセサリー - 150リットルから1,000リットルの容量を持つ移動可能な溶接鋼圧力ドラム 記事の内容: この欧州規格は、液化石油ガス（LPG）の150リットルから1,000リットルまでの容量を持つ移動可能な溶接鋼圧力ドラムの材料、設計、構造、仕事、装備、製造時の検査および試験に関する最低要件を規定しています。垂直および水平の円柱状の容器が対象となります。
기사 제목: EN 14893:2014 - LPG 장비 및 액세서리 - 150리터부터 1,000리터까지 용량이 있는 이동식 압력용 용접강철 드럼 기사 내용: 이 유럽 표준은 용량이 150리터 이상부터 1,000리터까지인 LPG의 이동식, 재충전 가능한 용접강철 압력 드럼에 대한 자재, 설계, 구조, 작업, 설비, 제조시 점검 및 시험에 대한 최소 요구사항을 명시한다. 세로 및 가로 원통형 용기가 포함된다.
The article discusses the European Standard EN 14893:2014, which outlines the requirements for transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums. These drums have volumes ranging from 150 liters to 1,000 liters and are used for storing LPG. The standard covers both vertical and horizontal cylindrical receptacles and specifies the minimum requirements for their material, design, construction, workmanship, equipping, inspection, and testing during manufacturing.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...